髋关节的考试

Hip pain affects millions of patients of all ages, and can be associated with various intra- and extra-articular pathologies. That is why it is imperative for every physician to understand how to properly examine this musculoskeletal region.

The hip is a ball and socket joint, which consists of the femoral head articulating with the acetabulum. When combined with the hip ligaments, it makes for a very strong and stable joint. However, despite the hip’s stability it possesses a considerable range of motion, and is prone to degeneration and wear and tear over time, or after injury.

This video will focus on the essential steps required to carry out a comprehensive hip examination, interspersed with relevant anatomical illustrations and discussion of the findings.

Like most musculoskeletal exams, begin with hip inspection and palpation.

Before you start, make sure that the patient has removed enough clothing to expose and compare both hips.

Inspect the area from the anterior, posterior, and lateral perspectives. Note any asymmetry due to muscle wasting or swelling. Instruct the patient to walk back and forth across the examination room. Observe the patient’s gait and check for any limp.

Then ask the patient to lie in supine position on the exam table so you can begin with palpation. Remember to wash your hands thoroughly before you touch the patient.

Start the palpation at the anterior hip joint. This is located along the front of the hip, just lateral to the groin. Tenderness here may suggest osteoarthritis, fracture, or avascular necrosis of the femoral head.

Next, assess the anterior superior iliac spine or ASIS, and the anterior inferior iliac spine or AIIS. For ASIS, palpate at the anterior tip of the iliac crest. This is the attachment site for the sartorius muscle, so tenderness here may suggest tendonitis or avulsion.

For AIIS, palpate just below and medial to the ASIS. This is the attachment site for the rectus femoris, and again, tenderness here may suggest tendonitis or avulsion.

From there move onto the greater trochanter. This is the bony prominence on the side of the hip, with its overlying trochanteric bursa – a “saclike” structure.

Subsequently, palpate the iliotibial band, which is a thick strip of connective tissue that runs down the lateral thigh.

Next, palpate the posterior superior iliac spine or PSIS, and the sacroiliac or the SI joint. For PSIS, palpate at the posterior tip of the iliac bone, and for SI joint, palpate just under PSIS. Tenderness here suggests inflammation or osteoarthritis at that joint.

Finally, palpate the gluteus muscle, the ischial tuberosity, and the coccyx. The gluteus muscle can be found below the PSIS. This is the main extensor of the hip. The Ischial tuberosity can be found at the base of the buttocks. This is where the hamstring muscles attach. The coccyx is located at the very tip of the lower spine and is often injured from trauma related to falls.

After the inspection and palpation portion of the exam is complete, move onto testing the hip’s range of motion, strength and sensory perception.

Hip’s range of motion should be tested passively. Start by having the patient seated; stabilize their knee at a 90° angle with one hand, and with the other hand check the internal rotation range by moving their foot away from the midline. The normal range of motion during this maneuver is about 30°.

In the same position, check the external rotation by moving the foot towards the midline. Normally, this would be about 60°.

Next, have the patient transition into supine position and test for hip abduction by holding at the ankle and pulling the leg away from the midline. Normally, the abduction is about 45°.

Subsequently, test for adduction by pulling their leg towards the midline until the pelvis tilts. The range of this motion should be about 30°.

Next, assess the hip flexion. Grasp the bent knee and pull it to the chest and stop when the back flattens. In a healthy patient, the flexion angle is about 120° without any complain of pain.

Lastly, request the patient to occupy a prone position to check hip extension. Attempt to lift the entire leg up and off the table, while supporting the knee. Normally, the hip can be extended by about 15° without any discomfort or pain.

After range of motion tests, perform the hip strength testing maneuvers. To avoid patient repositioning, start with the extension strength test. Ask the patient to raise their leg, while you push down at the mid shin. This tests the strength of the gluteus maximus and the hamstring muscles, which include the semi-tendinosus, the semi-membranosus and the biceps femoris.

Next, request the patient to turn around and occupy a supine position to perform the abduction strength test. . Instruct the patient to pull the feet apart, while you push the ankles together. This maneuver assesses the gluteus medius and the gluteus minimus muscles.

After that, test hip adduction strength. Ask them to push their feet together, while you try to pull the ankles apart. Hip adduction involves the adductor muscles – namely the longus, brevis, magnus, and gracilis.

Lastly, to test the flexion strength, assist the patient to move into seated position. Then, ask them to flex their hip upward, while you push down on their knee. This involves muscles like the iliopsoas, which refers to the combination of psoas major and the iliacus, the rectus femoris, and the Sartorius.

Following the strength tests, evaluate the sensory discomfort in the hip region. Using a light touch, test the distal lateral thigh area, where hypesthesia may indicate meralgia paresthetica, caused by compression of the lateral femoral cutaneous nerve. Then touch the area near the obturator nerve, which innervates the hip, as well as the medial thigh and knee, and may cause the hip pain to be felt in the knee region.

After performing all the above-mentioned maneuvers, evaluate the hip functioning using a variety of special tests.

The first of these tests is the “Trendelenburg Test”. Instruct the patient to stand on both feet and slowly raise one foot. Observe for a pelvic tilt toward the raised foot. A positive test indicates weak hip abductor muscles.

The second test is called the “Hop Test”. Ask the patient to hop unsupported on one leg. Look for reproduced pain at the groin area. This test is usually positive with a femoral neck stress fracture.

Next, ask to patient to lie down and measure the leg lengths from ASIS to the corresponding medial malleolus. Compare it to the other leg. Half-inch or more difference is significant and treated with a heel lift on the short side.

After that, conduct the “Log Roll Test” by passively rotating the patient’s pelvis in a gentle to-and-fro motion. Severe pain while doing so may indicate fracture, infection, or synovitis.

Next, perform the “FABER test”, which stands for Flexion, Abduction, and External Rotation test. While in the supine position, instruct the patient to place their ankle on top of the opposite knee. Discomfort while performing this action may suggest SI joint pathology.

Ultimately, perform the “Ober Test”. To do so, instruct the patient to lie on the unaffected side with their upper knee flexed at a 90° angle. Measure the distance of the flexed knee from the table. Inability of the patient to bring their knee down to the table suggests IT band tightness.

This concludes the hip exam. Thank the patient for their co-operation.

You have just watched a JoVE video detailing a comprehensive hip examination.

In this video, we reviewed the essential aspects of this exam including inspection for asymmetry, swelling, and gait abnormalities; palpation for areas of tenderness; range of motion and strength testing; sensory assessment; and additional special diagnostic maneuvers, which may help a clinician narrow down the differential diagnosis. As always, thanks for watching!