Waiting
Login processing...

Trial ends in Request Full Access Tell Your Colleague About Jove
JoVE Science Education
Earth Science

A subscription to JoVE is required to view this content.

 

Making a Geologic Cross Section

Overview

Source: Laboratory of Alan Lester - University of Colorado Boulder

Geologic maps were first made and utilized in Europe, in the mid-to-late 18th century. Ever since, they have been an important part of geological investigations all around the world that strive to understand rock distributions on the surface of the earth, in the subsurface, and their modification through time. A modern geologic map is a data-rich representation of rocks and rock-structures in a two-dimensional plan view. The base for most geologic maps is a topographic map, onto which color variations have been placed to represent specific rock units. The boundaries between the rock units are called contacts. In addition to the contact lines, geologic maps contain symbols that represent key features, such as the dip and strike of the rock units, anticlines and synclines, and the traces of fault surfaces.

Although the two-dimensional map-view is useful, one of a geologist's key tasks is to infer the type and orientation of rocks in the subsurface. This is done using geologic rules, inferences, and projections downward from the surface. The result is a geologic cross section, a view that essentially provides a cutaway image, much like one would see on a canyon wall or in a roadcut.

This hypothetical slice into the earth, providing a third dimension (depth), is the key to a host of geological applications. Cross sections are used to assess temporal models of rock formation through time. In other words, the goal is to recreate a step-by-step sequence of which rocks and structures came first, last, and in between. They're also used to determine specific modes of deformation - whether rocks have undergone compressional, extensional, or other stresses.

Geologic cross sections help to identify regions of groundwater movement, evaluate potential sites for economic mineral deposits, and locate oil and gas reservoirs.

Principles

Folds are evidence of plastic deformation-they typically form as a result of low-strain rates, high-confining pressures, and elevated temperature. In contrast, faults are indicative of brittle deformation-they typically result from high-strain rates, low-confining pressures, and overall lower temperatures.

Fold-type deformation that generates up-warped strata (i.e. analogous to an upside down bowl) are referred to as anticlines or antiforms; and those folds that involve down-warped strata are synclines or synforms. In many cases, a region that has undergone folding will show multiple sets of synclines and anticlines, like wrinkles on a carpet.

In both fold types (synclines and anticlines) the strata dip in opposite directions, either towards or away, from what is termed the fold axis. For example, with an anticline, the strata dip down and away from the fold axis, much like shingles on a roof dipping away from a ridge-line. The compass orientation of the fold axis is termed the "strike" direction of the fold.

The first step in constructing a geologic map is to take a topographic map and then color-code the regions that contain different rock types. Between each rock unit is a line, called the "contact" between identifiable units. Within each rock type (and sometimes on the contact itself) are given dip/strike symbols to show the surface outcrop orientation of the rock strata. (Note: Strike and dip are defined in a previous video involving the use of the Brunton Compass. In brief, dip is simply the angle that the rock layers make with a horizontal plane, and strike is the resultant azimuth compass orientation of the line that represents the intersection of the rock unit with a horizontal plane.) It is the extrapolation of these dips and strikes into the subsurface-through the use of the geologic cross section-that can be used to help infer the type of fold structure that is present. For example, beds dipping away from a central axis are indicative of anticlines, whereas beds that dip towards a central axis are indicative of synclines. Once the structure has been identified, the map will be marked with symbology that denotes the particular fold type that is present, and the strike of the fold axis.

It is worth noting that geologists can often infer these structures merely by looking at the plan-view geologic map, but the cross-section view provides a 3-D visual perspective that greatly enhances the ability to evaluate fold and fault structures, and locate them with great precision.

One of the primary uses of the geologic cross section is to reconstruct folds and faults that are somewhat cryptic, as a result of erosion removing their surface features. An anticline does not need to be a hill (an up-warping of earth material) and a syncline does not need to manifest itself as a valley (a down-warping of earth material). Earth's surface topography does not always imply a particular kind of fold or fault structure at depth.

Subscription Required. Please recommend JoVE to your librarian.

Procedure

  1. Identify two points that define a cross-section profile, e.g. A-A'.These points are chosen such that the line between them is approximately perpendicular to the strike directions of the intervening rock units.
  2. A topographic profile is drawn between the two points, A-A'. Directions for how to generate a topographic profile are provided in a different video.
  3. Take a strip of paper and align it along the line, carefully marking the contacts between the different rock units.
  4. Transfer the contacts onto the topographic profile.
  5. At each contact, the dip of the adjoining layers is used to project this boundary into the subsurface. As long as the topographical profile has no vertical exaggeration, the dips from the map can be directly used. For example, if the dip at a limestone/sandstone boundary (contact) is 20°, then that contact can be drawn as extending into the subsurface at an angle of 20°.
  6. Utilize this projection and knowledge of the local geology to infer the folds or faults in the subsurface. For example, rock layers that dip away from the central axis (again, like shingles on a peaked-roof) may indicate the presence of an anticline or antiform. In addition, if the rock layers along the central axis are older than those that are successively further from the axis, then this is further confirmation of an anticlinal structure.
  7. Extend the rock layers into the above ground region using dotted lines; this shows the inferred presence of rocks prior to erosion.
    As discussed in the Principles section, the dotted lines above the surface are effectively a representation of a geologic structure that once existed, but has been removed by erosion.

Geologic cross-sections can assess temporal models of rock formation through time.

Using geologic maps, cross-sections can be generated which predict the strata of the rocks sub-surface, and estimate the rock shape above ground prior to erosion.

The resulting cross-section is a cutaway image much like those seen in canyon walls or road cuts. While geologists may be able to infer such features from a plan-view geologic map, the addition of a cross-section provides a third dimension of information that can greatly enhance the ability to evaluate folds and faults.

This video will illustrate the process of creating a geologic cross section, and highlight some of the extensive uses of this geological tool.

The first step in creating a geologic map is to take a topographic map and onto this color-code the regions containing different rock types. In the field, geologists observe mineralogic and textural features, which are then used to identify distinct rock types and rock units. The lines between each rock unit section are the contacts. Within each rock type, strike and dip data will be added to illustrate the surface outcrop orientation of the rock strata.

These strike and dip data indicate fold-type deformations that generate up-warped strata, analogous to an upside down bowl, which are referred to as anticlines. The folds that involve down-warped strata are synclines. In contrast, faults are a result of brittle deformation, whereby rocks break instead of bending along a distinct surface-of-rupture. This surface is the "fault-plane."

Taken together, rock type, position, and orientation, are used to create a geologic cross-section. The first step is to create a topographic profile, which shows the elevation and contour of the target region. The geologic data is then added to this profile. This cross-section can now be used to infer the subterranean structure. For example, beds dipping away from a central axis are indicative of anticlines, whereas beds that dip towards would indicate synclines.

Further, geologic cross sections are used to reconstruct folds and faults that may be cryptic, due to the effects of erosion on the surface features. This is achieved by extrapolating the existing surface and subsurface data upwards above the existing plane.

Now that we are familiar with the principles behind the construction of a geologic cross section, let's take a look at how this is carried out on an example map.

To construct a geologic cross-section, first take a geologic map of the target survey area. Begin by choosing two points that define a cross section profile of interest. Label these points as A and A'. These should be selected so that a line between them will be approximately perpendicular to the strike directions of the intervening rock units. Connect these points, and create a topographical profile, without vertical exaggeration, based on the contours that intersect the line. Next, take a strip of paper and align it along the A-A' line, and carefully mark the contacts between the different rock units.

At each contact, the dip information of the adjoining layers is used to project the boundary into the subsurface. Note that in the projection to the subsurface, we use an average dip across the fold. This maintains constant bed thickness in the projection.

Using a protractor, measure the angle of the dip according to the original map, and extend the rock layers in straight lines below the surface. Projecting this information at each contact point will give a rough predicted cross-sectional view of the rock strata beneath the surface. Next, look for patterns in the rock projections that may indicate folds of the same type of rock strata. If these predicted strata lines appear to meet, this indicates folding of the same substrate, and they should be joined in a smooth projection based on the dip magnitudes given at the surface.

Finally, extend the rocks layers into the above ground region. This shows the inferred presence of rocks and geologic structure prior to erosion.

The map used for this demonstration shows a portion of the MASONVILLE, COLORADO, 7.5 minute quadrangle, USGS geologic map. The rock layers and contacts have been transferred to the geologic profile, and projections made into the subsurface and surface. In the case of one of the units, the Dakota group, labeled KD and highlighted in green, we see the layers dipping on one side of what is referred to as the anticline, to the east, and to the west on the opposite side. Overall, the projections suggest an anticline-syncline combination, and the crest of the anticline is recorded on the original map itself as a dashed line, with the trough (pronounce "trof") of the syncline indicated to the west by a different dashed line. This combination results in a bowed down set of rock formations, and a bowed up formation, produced by past compressional stresses on the rock strata. The Dakota group, which follows this anticline-syncline pattern, is a unit of importance as it represents a sandstone, which will contain water or oil, which may be of interest for mining.

Geologic cross-sections are useful tools for a number of types of geological investigation. Some of these applications are explored here.

Analyzing sequences of deposition, intrusion, deformation, or erosion over time can inform not only the spatial dimensions of the rock, but also the temporal dimension. Using this information, it is also possible to simulate and anticipate future changes in the Earth's structure, such as the erosion of softer substances, leaving harder rock exposed.

Most economically important mineral deposits; including gold, silver, copper, and molybdenum; are associated with igneous rocks. If such rocks are found on the surface during a geological survey, and their surface contacts can be assessed, it is possible to use a geologic cross section to extrapolate where possible ores can be found in the subsurface.

Geologic cross-sections are key to evaluating fluid flow in the subsurface. Understanding the orientation of flow-enhancing layers, or aquifers, versus flow preventing layers, or aquicludes, allows geologists to predict the motion of groundwater, and potentially determine suitable areas for drilling of wells. In general, rock types containing considerable pore space, like sandstone, will be aquifers, and those with denser structure and little pore space, like slate, will act as aquicludes. Crucially, this information also allows for analysis of aqueous pollutant movement, and development of possible mitigation strategies in such events.

You've just watched JoVE's introduction to geologic cross-sections. You should now understand how to create a geologic profile from a geologic map, and the uses and applications of these geologic cross-sections.

Thanks for watching!

Subscription Required. Please recommend JoVE to your librarian.

Results

For this demonstration, a portion of the Carter Lake, Colorado, USGS 7.5-minute Quadrangle Map was used. This notation means that 7.5 minutes of longitude and 7.5 minutes of latitude define the E-W and N-S boundaries on the map. On the east side of the cross section line A-A', the rock layers dip to the west; in contrast, on the west side, the layers dip to the east. It can be inferred that these layers meet in the subsurface to form a bowl-shaped fold-structure, known as syncline. Ultimately, all folds (whether down-warps, such as synclines, or up-warps, such as anticlines) are a product of compression-style deformation. When rocks have been squeezed, they show plastic deformation features (folding), especially if deformation has occurred relatively rapidly, with high-confining pressures and elevated temperatures in Earth's upper crust. In contrast, rapid application of stress, low-confining pressure, and low temperatures are more likely to produce brittle deformation, known as faulting.

Subscription Required. Please recommend JoVE to your librarian.

Applications and Summary

Cross-sections provide a means to analyze and assess the subsurface orientation of rock units. Geologists use the relative dating rules of cross-cutting and superposition to determine the timing of deposition and deformation. For example, when one layer sits above another, it can be inferred that the top layer is most likely younger than the layer below. Furthermore, if a fault cuts across a particular rock unit, then the fault is most likely younger than the rock unit it offsets.

Some specific applications include the determination of geologic history, groundwater flow analysis, mineral deposits, and oil and gas reservoirs. Relative dating techniques permit an assessment of a sequence of geologic events, including deposition, intrusion, and deformation (folds and faults). Geologists seek to understand the earth in not only the three spatial dimensions, but also within the context of a temporal dimension- the idea being to reconstruct geological change through time.

Cross sections are a key to evaluating fluid flow in the subsurface. Understanding the orientation of flow-enhancing layers (aquifers) versus flow-preventing layers (aquicludes) is the key to evaluating the motion of groundwater. This also provides an application for determining where wells are best to be drilled. It allows for analysis of aqueous pollutant movement and possible mitigation strategies. In general, rock types that contain considerable pore space (e.g. sandstone or highly fractured igneous/metamorphic rocks) will be aquifers. In contrast, rock types that contain limited pore space (or pores that lack inter-connectivity) will more likely be aquicludes.

Most economic mineral deposits (e.g., Au, Ag, Cu, Mo, etc.) are associated with igneous rocks. If igneous rocks outcrop on the surface, and their surface contacts can be assessed, then one can determine where possible ores can be found in the subsurface. Most oil and gas reservoirs are associated with sedimentary rocks, because these are the rock types that contain hydrocarbon sources (decayed organics, both terrestrial and marine). Here, cross section analysis is absolutely critical to determining where fold or fault traps are likely to exist, and if they contain petroleum resources. For example, up-warps (anticlines) are a classic location for oil and gas drilling. This is because mobile hydrocarbons tend to flow upward, within permeable layers, until they reach the peak (or axis) of an anticline. If the permeable layer is capped by an impermeable layer, then a hydrocarbon reservoir accumulates and pools at the apex of the fold.

Subscription Required. Please recommend JoVE to your librarian.

Transcript

Tags

Geologic Cross-section Temporal Models Rock Formation Geologic Maps Sub-surface Strata Rock Shape Erosion Cutaway Image Canyon Walls Road Cuts Folds Faults Plan-view Geologic Map Three Dimensions Of Information Topographic Map Color-code Regions Rock Types Rock Units Contacts Strike And Dip Data Surface Outcrop Orientation Fold-type Deformations Anticlines Synclines Faults

Get cutting-edge science videos from JoVE sent straight to your inbox every month.

Waiting X
Simple Hit Counter