Determination of 45 Pesticides in Avocado Varieties by the QuEChERS Method and Gas Chromatography-Tandem Mass Spectrometry

Summary

The present protocol describes the analysis of multiclass pesticide residues in avocado varieties using the Quick-Easy-Cheap-Effective-Rugged-Safe (QuEChERS) method with ammonium formate, followed by gas chromatography-tandem mass spectrometry.

Abstract

Gas chromatography (GC) tandem mass spectrometry (MS/MS) stands as a preeminent analytical instrument extensively employed for the surveillance of pesticide residues in food. Nevertheless, these methods are vulnerable to matrix effects (MEs), which can potentially affect accurate quantification depending on the specific combination of analyte and matrix. Among the various strategies to mitigate MEs, matrix-matched calibration represents the prevailing approach in pesticide residue applications due to its cost-effectiveness and straightforward implementation. In this study, a total of 45 representative pesticides were analyzed in three different varieties of avocado (i.e., Criollo, Hass, and Lorena) using the Quick-Easy-Cheap-Effective-Rugged-Safe (QuEChERS) method with ammonium formate and GC-MS/MS.

For this purpose, 5 g of the avocado sample was extracted with 10 mL of acetonitrile, and then 2.5 g of ammonium formate was added to induce phase separation. Subsequently, the supernatant underwent a cleanup process via dispersive solid-phase extraction employing 150 mg of anhydrous MgSO₄, 50 mg of primary-secondary amine, 50 mg of octadecylsilane, 10 mg of graphitized carbon black, and 60 mg of a zirconium oxide-based sorbent (Z-Sep+). The GC-MS/MS analysis was successfully performed in less than 25 min. Rigorous validation experiments were carried out to assess the performance of the method. The examination of a matrix-matched calibration curve for each variety of avocado revealed that the ME remained relatively consistent and less than 20% (considered as a soft ME) for most pesticide/variety combinations. Furthermore, the method´s limits of quantification were lower than 5 µg/kg for all three varieties. Finally, the recovery values for most pesticides fell within the acceptable range of 70-120%, with relative standard deviation values below 20%.

Introduction

In chemical analysis, the matrix effect (ME) can be defined in various ways, but a widely accepted general definition is as follows: it refers to the change in the signal, particularly a change in the slope of the calibration curve when the sample matrix or portion of it is present during the analysis of a specific analyte. As a critical aspect, ME necessitates thorough investigation during the validation process of any analytical method, as it directly affects the accuracy of quantitative measurement for the target analytes¹. Ideally, a sample pretreatment procedure should be selective enough to avoid extracting any components from the sample matrix. However, despite significant efforts, many of these matrix components still end up in the final determination systems in most cases. Consequently, such matrix components often compromise the recovery and precision values, introduce additional noise, and escalate the overall cost and labor involved in the method.

In gas chromatography (GC), ME arises due to the presence of active sites within the GC system, which interact with the target analytes through various mechanisms. On the one hand, the matrix constituents block or mask these active sites that would otherwise interact with the target analytes, resulting in frequent signal enhancement². On the other hand, active sites that remain unobstructed may cause peak tailing or analyte decomposition due to strong interactions, leading to a negative ME. However, this can offer potential benefits in certain cases². It is crucial to emphasize that achieving complete inertness in a GC system is exceedingly challenging, despite using highly inert components and proper maintenance. With continuous use, the accumulation of matrix components in the GC system becomes more pronounced, causing an increased ME. Nowadays, it is widely recognized that analytes containing oxygen, nitrogen, phosphorus, sulfur, and similar elements, exhibit a greater ME as they readily interact with these active sites. Conversely, highly stable compounds such as hydrocarbons or organohalogens do not undergo such interactions and do not show observable ME during analysis^2,3.

Overall, ME cannot be fully eliminated, leading to the development of several strategies for compensation or correction when complete removal of matrix components is not feasible. Among these strategies, the utilization of deuterated internal standards (ISs), analyte protectants, matrix-matched calibration, the standard addition method, or the modification of injection techniques have been documented in scientific literature^1,2,4,5. The SANTE/11312/2021 guidelines have also recommended these strategies⁶.

Regarding the application of matrix-matched calibration to compensate for MEs, sample sequences in practical situations encompass diverse types of foods or various samples from the same commodity. In this case, the assumption is made that employing any sample from the same commodity will effectively compensate for ME in all samples. However, there is a lack of sufficient studies in the existing literature that specifically investigate this issue⁷.

The multiresidue determination of pesticides in matrices containing an appreciable percentage of fat and pigments constitutes a challenging task. The considerable amount of coextracted material can significantly affect the extraction efficiency and interfere with the subsequent chromatographic determination, potentially damaging the column, source, and detector, and resulting in significant MEs^8,9,10. Consequently, the analysis of pesticides at trace levels in such matrices necessitates a significant reduction of matrix components before analysis while ensuring high recovery values⁷. Obtaining high recovery values is crucial to ensure that pesticide analyses remain reliable, accurate, and compliant with regulatory standards. This is vital for ensuring food safety, environmental protection, and informed decision-making in agriculture and related fields.

Avocado is a fruit of high commercial value cultivated in tropical and Mediterranean climates worldwide and widely consumed both in its regions of origin and in the numerous export markets. From the analytical point of view, avocado is a complex matrix containing a significant number of fatty acids (i.e., oleic, palmitic, and linoleic), similar to nuts, a significant pigment content, as in green leaves, as well as sugars and organic acids, similar to those found in other fruits¹¹. Due to its fatty nature, special attention must be given when employing any analytical method for analysis. While pesticide residue analysis has been conducted on avocados using GC-MS in some instances^{8,12,13,14,15,16,17,18,19,20}, it has been relatively less frequent compared to other matrices. In most cases, a version of the Quick-Easy-Cheap-Effective-Rugged-Safe (QuEChERS) method has been applied^{8,12,13,14,15,16,17,18}. None of these studies have investigated the consistency of MEs among different avocado varieties.

Therefore, the aim of this work was to study the consistency of MEs and recovery values for 45 representative pesticides across different varieties of avocado (i.e., Criollo, Hass, and Lorena) using the QuEChERS method with ammonium formate and GC-MS/MS. To the best of our knowledge, this is the first time that this type of study has been conducted on such fatty matrix samples.

Protocol

1. Preparation of the stock and working solutions

NOTE: For safety reasons, it is advisable to wear nitrile gloves, a laboratory coat, and safety glasses throughout the protocol.

1. Prepare individual stock solutions of each of the 45 commercial pesticide standards (see Table of Materials) at approximately 1,000 mg/L in acetonitrile in 10 mL volumetric flasks.
2. Combine the above individual stock solutions to prepare a 400 mg/L stock solution in acetonitrile in a 25 mL volumetric flask.
   NOTE: This mixed solution will be utilized to prepare the working solutions for recovery and calibration experiments.
3. Prepare stock solutions of atrazine-d₅ and triphenyl phosphate (TPP) at concentrations of 750 mg/L and 1,050 mg/L, respectively, in acetonitrile in 10 mL volumetric flasks. Utilize atrazine-d₅ as a procedural internal standard (P-IS) and TPP as an injection internal standard (I-IS).
   NOTE: The ideal scenario would involve the utilization of an isotopically labeled internal standard for each specific target analyte.
4. Prepare stock recovery solutions in acetonitrile containing 0.05% (v/v) of formic acid (to prevent degradation) in 10 mL volumetric flasks to yield 10, 100, and 400 µg/kg sample equivalents for the pesticides and 200 µg/kg for the P-IS separately. Store these solutions in amber glass vials in the dark at −20 °C.
5. Prepare calibration solutions of the pesticides and P-IS together in acetonitrile with 0.05% (v/v) of formic acid in 10 mL volumetric flasks to yield 5, 10, 25, 75, 200, 400, and 600 µg/kg, and 200 ng/ng, respectively, and store them in amber glass vials in the darkness at −20 °C.
   NOTE: The same solutions may be utilized throughout the experimental work but storing them under the specified conditions immediately after each use is essential.
6. Prepare a mixture of analyte protectants containing 100 g/L of 3-ethoxy-1,2-propanediol, 10 g/L of L-gulonic acid γ-lactone, 10 g/L of D-sorbitol, and 5 g/L of shikimic acid in a 4/1 (v/v) ratio of acetonitrile to water with 0.5% (v/v) of formic acid.
   NOTE: This mixture of analyte protectants is to be added just before the injection to mitigate ME.

2. Sample collection

1. Collect samples from three avocado species (e.g., Criollo, Hass, and Lorena) available at supermarkets. Ensure that each sample weighs approximately 1 kg, which is enough for conducting all the subsequent studies and aligns with Directive 2002/63/CE²¹.
   NOTE: Organic samples were preferentially selected to minimize the likelihood of the presence of pesticide residues.
2. Transport the collected avocado samples to the laboratory, and individually homogenize them without the pipe using a chopper (see Table of Materials). Store the homogenized samples in amber glass containers at 4 °C until analysis.
   NOTE: The same avocado samples will be used throughout the entire study. Therefore, it is crucial to store them under the specified conditions immediately after each use.

3. Sample preparation utilizing the QuEChERS method with ammonium formate

NOTE: Figure 1 illustrates a schematic representation of the QuEChERS method with ammonium formate.

1. Weigh 5 g of each avocado sample in a 50 mL centrifuge tube (see Table of Materials).
2. Add 50 µL of the P-IS solution to yield a concentration of 200 µg/kg. For recovery assessment, also add the pesticide solutions prepared in step 1.4 to yield concentrations of 10, 100, and 400 µg/kg (n = 5 each).
3. Vortex the tube for 30 s to ensure thorough integration of the spike into the sample.
4. Add 10 mL of acetonitrile to the centrifuge tube. Shake the tube at 70 rpm for 5 min.
5. Add 2.5 g of ammonium formate, shake the tube again at 70 rpm for 5 min, and subsequently centrifuge it at 1,800 × g for 5 min.
6. To a 2 mL centrifuge tube containing 150 mg of anhydrous MgSO₄, 50 mg of primary-secondary amine (PSA), 50 mg of octadecylsilane (C₁₈), 10 mg of graphitized carbon black (GCB), and 60 mg of a zirconium oxide-based sorbent Z-Sep+, add 1 mL of the extract for purification utilizing dispersive-solid phase extraction (d-SPE). Vortex the tube for 30 s and centrifuge it at 1,800 × g for 5 min.
7. Transfer 200 µL of the extract to an autosampler vial, add 20 µL of the analyte protectant solution prepared in step 1.6, and include 50 µL of the TPP solution.
8. Perform instrumental analysis using a GC-MS/MS system (see section 4).
9. Perform matrix-matched calibration following the same procedure as described above, using blank extracts, except, during the d-SPE step (step 3.6), clean 5 mL of the supernatant in 15 mL tubes. Add the spike and P-IS solutions at step 3.7. Add the calibration standard solutions to the autosampler vials to yield 5, 10, 25, 50, 100, 200, 400, and 600 µg/kg, along with the TPP, resulting in a final volume of 270 µL.
   NOTE: Overall, be sure to construct matrix-matched calibration curves for each avocado variety plus the acetonitrile-only calibrations.

4. Instrumental analysis using GC-MS/MS

1. Conduct the analyses employing a GC-MS/MS system with a triple quadrupole (TQ) equipped with an electron ionization interface (−70 eV) and an autosampler (see Table of Materials).
2. Employ an MS GC column (silica Bond of 30 m length, 0.25 mm inner diameter, 0.25 µm film thickness) along with ultrahigh purity Helium as the carrier gas at a constant flow rate of 1.2 mL/min.
3. Verify the following parameters before proceeding with the equipment operation:
   1. Ensure that the gas pressures are correct: Helium at 140 psi and Argon at 65 psi.
   2. Check the condition of the rotary pump oil to ensure that it is clear and at the appropriate level.
   3. Ensure that the injection syringe does not have any obstructions from previous injections.
   4. Confirm that the wash vials contain a sufficient volume of each solvent.
   5. Check that the consumables counter (septum, liner) has not reached its limit.
4. Turn on the main GC switch located on the front panel and turn on the MS switch located at the back.
5. Open the GCMS Real Time Analysis software that controls all the parameters of the GC-MS/MS system.
   NOTE: The instrument system includes the GCMS Real Time Analysis software by default.
6. Click on Vacuum Control | Advanced | Rotary Pump 1 to initiate the vacuum system.
   NOTE: In this window, monitor the pressure to determine the optimal vacuum values, which should be lower than 9.0 Pa. It will take approximately 12 h.
7. Click on Start to turn on turbo molecular pump 1 and turbo molecular pump 2.
8. Click on Start for the Ion Source Heater option.
   NOTE: After a recommended time of 1 h, check the system's vacuum to confirm that the recommended value is lower than 1.6e^-3 Pa.
9. Set the MS interface temperature to 250 °C and the ion source temperature to 300 °C.
10. Maintain the GC oven at an initial temperature of 50 °C for 1 min, then ramp it up to 180 °C at a rate of 25 °C/min. Subsequently, increase the temperature to 230 °C at 5 °C/min and then to 290 °C at 25 °C/min. Finally, keep the temperature constant at 290 °C for 6 min. The total analysis time is 24.6 min.
11. Click on Close once all these systems are turned on.
12. Click on the Tuning option from the analysis software and click on Peak Monitor View to perform an initial verification of the mass spectrometer conditions.
    ​NOTE: If necessary, perform autotuning.
13. Click on Acquisition, and from the displayed window, click on Download Initial Parameters. Verify that the equipment is ready GC and ready MS.

5. Data acquisition

1. Click on New Batch File from the software and create a sequence containing information such as sample name, sample ID, method file, data file, injection volume, and tuning file. Add rows as necessary and click on Save.
2. Click on Batch Start and let the injection process commence.
3. Perform the injection at 250 °C in the splitless mode, maintaining an injection volume of 1 µL. After 1 min following the injection, open the split.
   NOTE: Between injections, be sure to clean the 10 µL syringe with methanol, ethyl acetate, and acetonitrile, using a single rinse with each solvent. All the injections are performed in triplicate.
4. Analyze the analytes using the multiple reaction monitoring (MRM) mode, which is the standard mode employed in MS/MS systems with a TQ.
   NOTE: Table 1 provides the retention times (in min) and the quantifier and qualifier transitions for the multiclass pesticides, P-IS, and I-IS. The quantitative analysis relies on the ratio of the peak area of the quantitation ion to the P-IS ion. The I-IS is employed for quality control during injection. Supplementary File 1 contains chromatograms for all the 45 analyzed pesticides.
5. Open the Postrun Analysis software for data analysis.
   NOTE: The instrument system includes the GCMS Postrun Analysis software by default.
6. Click on the injection to be analyzed, navigate through the table containing the analytes, and select the peak of interest.
7. Click on the peak or the region of interest to visualize the chromatogram. Review the peak integrations, and if necessary, perform manual integration. Verify the areas of all analytes to perform the necessary calculations and method evaluation.

Results

Comprehensive validation of the analytical method was conducted according to SANTE/11312/2021 guidelines⁶, encompassing assessments of linearity, ME, recovery, and repeatability.

For the linearity assessment, matrix-matched calibration curves were constructed using spiked blank samples at multiple concentration levels (ranging from 5 to 600 µg/kg). The determination coefficients (R²) for most of the selected pesticides were found to be higher than or equal to...

Discussion

The primary limitation associated with matrix-matched calibration arises from the use of blank samples as calibration standards. This leads to an augmented number of samples to be processed for analysis and an increased injection of matrix components in each analytical sequence, potentially leading to higher instrument maintenance demands. Nonetheless, this strategy is more suitable than standard addition, which would generate a much larger number of samples to be injected due to the need to perform a calibration curve f...

Materials

List of materials used in this article

Name	Company	Catalog Number	Comments
3-Ethoxy-1,2-propanediol	Sigma Aldrich	260428-1G
Acetonitrile	Merk	1006652500
Ammonium formate	Sigma Aldrich	156264-1KG
AOAC 20i/s autosampler	Shimadzu	221-723115-58
Automatic shaker MX-T6-PRO	SCILOGEX	8.23222E+11
Balance	OHAUS	PA224
Centrifuge tubes, 15 mL	Nest	601002
Centrifuge tubes, 2 mL	Eppendorf	4610-1815
Centrifuge tubes, 50 mL	Nest	602002
Centrifuge Z206A	MERMLE	6019500118
Choper 2L	Oster	2114111
Column SH-Rxi-5sil MS, 30 m x 0.25 mm, 0.25 µm	Shimadzu	221-75954-30	MS GC column
Dispensette 5-50 mL	BRAND	4600361
DSC-18	Sigma Aldrich	52600-U
D-Sorbitol	Sigma Aldrich	240850-5G
Ethyl acetate	Merk	1313181212
GCMS-TQ8040	Shimadzu	211552
Graphitized carbon black	Sigma Aldrich	57210-U
Injection syringe	Shimadzu	LC2213461800
L-Gulonic acid γ-lactone	Sigma Aldrich	310301-5G
Linner splitless	Shimadzu	221-4887-02
Magnesium sulfate anhydrus	Sigma Aldrich	M7506-2KG
Methanol	Panreac	131091.12.12
Milli-Q ultrapure (type 1) water	Millipore	F4H4783518
Pipette tips 10 - 100 µL	Biologix	200010
Pipette tips 100 - 1000 µL	Brand	541287
Pipette tips 20 - 200 µL	Brand	732028
Pipettes Pasteur	NORMAX	5426023
Pippette Transferpette S variabel 10 - 100 µL	BRAND	704774
Pippette Transferpette S variabel 100 - 1000 µL	BRAND	704780
Pippette Transferpette S variabel 20 - 200 µL	SCILOGEX	7.12111E+11
Primary-secondary amine	Sigma Aldrich	52738-U
Shikimic acid	Sigma Aldrich	S5375-1G
Syringe Filter PTFE/L 25 mm, 0.45 µm	NORMAX	FE2545I
Triphenyl phosphate (QC)	Sigma Aldrich	241288-50G
Vials with fused-in insert	Sigma Aldrich	29398-U
Z-SEP+	Sigma Aldrich	55299-U	zirconium oxide-based sorbent
Pesticides			CAS registry number
4,4´-DDD	Sigma Aldrich	35486-250MG	72-54-8
4,4´-DDE	Sigma Aldrich	35487-100MG	72-55-9
4,4´-DDT	Sigma Aldrich	31041-100MG	50-29-3
Alachlor	Sigma Aldrich	45316-250MG	15972-60-8
Aldrin	Sigma Aldrich	36666-25MG	309-00-2
Atrazine	Sigma Aldrich	45330-250MG-R	1912-24-9
Atrazine-d5 (IS)	Sigma Aldrich	34053-10MG-R	163165-75-1
Buprofezin	Sigma Aldrich	37886-100MG	69327-76-0
Carbofuran	Sigma Aldrich	32056-250-MG	1563-66-2
Chlorpropham	Sigma Aldrich	45393-250MG	101-21-3
Chlorpyrifos	Sigma Aldrich	45395-100MG	2921-88-2
Chlorpyrifos-methyl	Sigma Aldrich	45396-250MG	5598-13-0
Deltamethrin	Sigma Aldrich	45423-250MG	52918-63-5
Dichloran	Sigma Aldrich	45435-250MG	99-30-9
Dichlorvos	Sigma Aldrich	45441-250MG	62-73-7
Dieldrin	Sigma Aldrich	33491-100MG-R	60-57-1
Diphenylamine	Sigma Aldrich	45456-250MG	122-39--4
Endosulfan A	Sigma Aldrich	32015-250MG	115-29-7
Endrin	Sigma Aldrich	32014-250MG	72-20-8
EPN	Sigma Aldrich	36503-100MG	2104-64-5
Esfenvalerate	Sigma Aldrich	46277-100MG	66230-04-4
Ethion	Sigma Aldrich	45477-250MG	563-12-2
Fenamiphos	Sigma Aldrich	45483-250MG	22224-92-6
Fenitrothion	Sigma Aldrich	45487-250MG	122-14-5
Fenthion	Sigma Aldrich	36552-250MG	55-38-9
Fenvalerate	Sigma Aldrich	45495-250MG	51630-58-1
HCB	Sigma Aldrich	45522-250MG	118-74-1
Iprodione	Sigma Aldrich	36132-100MG	36734-19-7
Lindane	Sigma Aldrich	45548-250MG	58-89-9
Malathion	Sigma Aldrich	36143-100MG	121-75-5
Metalaxyl	Sigma Aldrich	32012-100MG	57837-19-1
Methidathion	Sigma Aldrich	36158-100MG	950-37-8
Myclobutanil	Sigma Aldrich	34360-100MG	88671-89-0
Oxyfluorfen	Sigma Aldrich	35031-100MG	42874-03-3
Parathion-methyl	Sigma Aldrich	36187-100MG	298-00-0
Penconazol	Sigma Aldrich	36189-100MG	66246-88-6
Pirimiphos-methyl	Sigma Aldrich	32058-250MG	29232-93-7
Propiconazole	Sigma Aldrich	45642-250MG	60207-90-1
Propoxur	Sigma Aldrich	45644-250MG	114-26-1
Propyzamide	Sigma Aldrich	45645-250MG	23850-58-5
Pyriproxifen	Sigma Aldrich	34174-100MG	95737-68-1
Tolclofos-methyl	Sigma Aldrich	31209-250MG	5701804-9
Triadimefon	Sigma Aldrich	45693-250MG	43121-43-3
Triflumizole	Sigma Aldrich	32611-100MG	68694-11-1
α-HCH	Sigma Aldrich	33377-50MG	319-86-8
β-HCH	Sigma Aldrich	33376-100MG	319-85-7