Waiting
Login processing...

Trial ends in Request Full Access Tell Your Colleague About Jove

A subscription to JoVE is required to view this content.

Education
Microbial and Fungal Diversity
 

Microbial and Fungal Diversity

Procedure

  1. Examining Microbial Colony Structures
    • To begin, collect your allocated culture plates and then remove the Parafilm and lid from one of them.
    • Place the uncovered plate under a dissecting microscope and then observe the individual communities within each quadrant of the plate.
    • As the colonies are identified, fill out the observed colony properties in the appropriate column in the table. Click Here to download Table 1
    • Then, repeat the observations for each of the other two bacterial species.
    • To perform Gram staining of your three bacterial species, first label the ends of three microscope slides with the initials of each bacteria species, your initials, and the date. HYPOTHESES: In this experiment, the experimental hypothesis might be that it is possible to elucidate different bacterial species and shapes using Gram staining, and that Gram-positive bacteria will stain purple with crystal violet whereas Gram-negative bacteria will appear pink due to the safranin counterstain. The null hypothesis could be that all of the bacterial types will retain both stains equally, and staining will not help elucidate their species or shape.
    • To begin the first stain, attach a clip to the slide for ease of handling. For each bacterial smear, remember to be sure to use a cleaned and flame-sterilized inoculating loop.
    • Place two loopfuls of sterile distilled water onto the center of the slide.
    • After sterilizing the loop again, cool the loop by touching an uninoculated portion of the agar several times.
    • Then, remove a small amount of culture from an isolated colony and mix it with the water on the slide.
    • Allow the slide to dry at room temperature and heat-fix the smear by quickly passing it through a flame.
    • Once dry, pipette several drops of crystal violet onto the slide and let it sit for two to three minutes.
    • Carefully rinse the slide with distilled water by aiming the direct flow towards the top of the slide, allowing the water to gently flow down. Do not aim the water flow directly at the smear.
    • Next, cover the slide with Gram's iodine, leave it to sit again for two minutes, and then gently rinse with distilled water.
    • Decolorize the slide with 95% ethanol until stain no longer washes away.
    • Immediately, rinse the slide with distilled water. This will limit over-decolorizing.
    • Then, add several drops of safranin counterstain and leave for 30 s. This will stain any Gram-negative cells present.
    • Gently rinse the slide with distilled water and blot dry with absorbent paper.
    • After staining the other two slides in the same manner (steps 6 – 17), observe each with a microscope.
    • Use a low power objective first to make coarse adjustments. When you find an ideal section, move on to the higher magnifications.
    • After further imaging and adjusting the smear with a medium power objective, add immersion oil directly to the smear. NOTE: The oil is needed for high power objectives that will provide the best micrographs.
    • Now, use colored pencils to draw the observed bacteria in the appropriate magnification circles and fill in the observed characteristics in the appropriate column, noting the bacteria's shape and whether it is Gram-positive, identified by darker purple staining, or Gram-negative, identified with pink staining. Click Here to download Table 2
    • Finally, repeat the observation, drawing, and characterization for the other two stained bacterial slides.
  2. Examining Fungal Structures
    • Remove the S. cerevisiae plate from the incubator and place a drop of water onto a microscope slide.
    • Using a sterilized inoculating loop, smear a film of yeast into the drop of water and place a cover slip over the slide.
    • Place the slide under the microscope at the lowest magnification, increasing the magnification to the oil immersion setting to see the individual yeast cells.
    • Observe the general shape and structure of the yeast and identify any cells that are undergoing asexual reproduction by budding.
    • Now, draw the cells in the appropriate magnification circles.
    • When you are done observing the yeast, replace the S. cerevisiae slide with a prepared Ascomycetes apothecium slide and set the microscope to the lowest magnification.
    • Using colored pencils, draw the structures at low and high magnifications, including the asci and ascospores.
    • Finally, place a button mushroom, Agaricus bisporus, under the dissecting microscope and draw the features, including the pileus, or cap, the gills, and the stipe, or stalk.
  3. Results
    • Using the coloring of the bacteria recorded in the table, determine which species are Gram-positive and which are Gram-negative.
    • Then, look at the shapes recorded in the table to determine which bacterial species are bacillus, coccus, or spirillum.
    • Next compare your illustrations of the yeast cells to your illustrations of the bacterial cells. NOTE: Yeast from the Ascomycetes phylum, such as S. cerevisiae, can reproduce asexually, which can be observed through the budding of the cells under a microscope.
    • Record any observations of yeast cells budding. NOTE: Ascomycetes can also reproduce sexually via mitosis and haploid spore formation.
    • Record any observations of spore or asci formation you observed in the table.
    • NOTE: Fungus from the Basidiomycota phylum exhibit clearly observable gills under the pileus.
    • Record any fungal species that demonstrated gills under the pileus.

Tags

JoVE Lab Lab: 24 Procedure

Get cutting-edge science videos from JoVE sent straight to your inbox every month.

Waiting X
Simple Hit Counter