Name: first-order circuits in flashing lamps
Uploaded: 2024-04-11T12:48:43.000Z
Duration: 1 min 15 s
Channel: JoVE

تسمى الدوائر الكهربائية ذات المقاومات وعنصر تخزين الطاقة الفردي - مكثف أو محث دوائر من الدرجة الأولى.
يتم وصفها بمعادلة تفاضلية من الدرجة الأولى تربط إشارات الإدخال والإخراج.
تستخدم دوائر RC في مذبذبات الاسترخاء مثل دوائر مذبذب مصباح النيون.
عند تطبيق الجهد ، يبدأ المكثف في الشحن ، ويعمل المصباح كدائرة مفتوحة. عندما يصل المكثف إلى الجهد المطلوب لتأين غاز النيون ، يصبح المصباح دائرة كهربائية قصيرة.
يقوم المكثف بتفريغ ، مما يخلق وميضا ، وتتكرر العملية.
يعتمد الفاصل الزمني بين الومضات على ثابت الوقت ، وهو قابل للتعديل عن طريق ضبط قيم R و C.
في مصابيح الأنبوب ، يتم استخدام دائرة RL ، مع خنق كمحث ومقاومة الأسلاك المتأصلة تعمل كمقاوم.
عند تطبيق الجهد ، يقاوم الخانق الزيادات المفاجئة في التيار ، مما يولد قوة دافعة دافعة يزداد مع الجهد المطبق. هذا القوة الدافعة الكهربية يؤين الغاز ، ويضيء ضوء الأنبوب.
في دائرة RL ، يكون الحث على المقاومة هو ثابت الوقت.

لم يتم الإعلان عن أي تضارب في المصالح.

دوائر الرتبة الأولى

First-Order Circuits

<div style="direction:rtl">تعتبر الدوائر الكهربائية من الدرجة الأولى، والتي تشتمل على مقاومات وعنصر واحد لتخزين الطاقة - إما مكثف أو ملف حث، أساسية للعديد من الأنظمة الإلكترونية. تخضع هذه الدوائر لمعادلة تفاضلية من الدرجة الأولى تصف العلاقة بين إشارات الإدخال والإخراج. أحد الأمثلة الشائعة لدائرة من الدرجة الأولى هي دائرة RC (مكثف المقاوم). تستخدم هذه الدوائر في مذبذبات الاسترخاء مثل دوائر مذبذب مصابيح النيون. عندما يتم تطبيق الجهد على دائرة RC، يبدأ المكثف في الشحن، ويعمل المصباح كدائرة مفتوحة. عندما يتم شحن المكثف إلى الجهد المطلوب لتأين غاز النيون داخل المصباح، يتحول المصباح فجأة إلى دائرة كهربائية قصيرة. يؤدي هذا إلى تفريغ المكثف، مما يؤدي إلى وميض من الضوء. بمجرد تفريغ المكثف بالكامل، تتكرر العملية، مما يؤدي إلى تأثير الوميض المستمر. يعتمد الفاصل الزمني بين هذه الومضات على الثابت الزمني للدائرة، والذي يمكن ضبطه عن طريق ضبط قيم المقاومة (R) والسعة (C). ومن خلال اختيار هذه القيم بعناية، يمكن التحكم في تكرار الومضات. في المصابيح الأنبوبية، يتم استخدام نوع مختلف من دوائر الدرجة الأولى، المعروفة باسم دائرة RL (مقاوم- محفز). يعمل ملف الاختناق الموجود في أنبوب الضوء كمحث، بينما تعمل المقاومة المتأصلة للسلك كمقاوم. عند تطبيق الجهد الكهربي، يقاوم الخانق الزيادة المفاجئة في التيار، مما يولد قوة دافعة كهربائية (emf) ترتفع مع الجهد المطبق. تؤدي هذه القوة الدافعة الكهربية إلى تأين الغاز الموجود داخل أنبوب الضوء، مما يؤدي إلى إضاءته. في دائرة RL، يتم تعريف ثابت الوقت على أنه الحث (L) على المقاومة (R). يلعب هذا الثابت الزمني دورا حيويا في تحديد مدى سرعة استجابة الدائرة للتغيرات في إشارة الإدخال. كلما زاد الثابت الزمني، كانت استجابة الدائرة أبطأ، والعكس صحيح.</div>

تسمى الدوائر الكهربائية ذات المقاومات وعنصر تخزين الطاقة الفردي - مكثف أو محث دوائر من الدرجة الأولى.
يتم وصفها من قبل ...

Education

JoVE Core

Electrical Engineering

الهندسة الكهربائية

Unit 1

الوحدة الأولى

First and Second-Order Circuits

الدوائر ذات الرتبة الأولى والثانية

KEY TERMS AND CONCEPTS

المصطلحات والمفاهيم الأساسية

first-order circuits in flashing lamps

First-order circuits use a resistor and one energy storage element, either a capacitor or an inductor. They are common in electronic systems and are described by a first-order differential equation that links the input and output signals.

One important example is the RC circuit, which uses a resistor and a capacitor. In a relaxation oscillator such as a neon lamp circuit, the capacitor starts charging when voltage is applied. At first, the lamp behaves like an open circuit. When the capacitor reaches the voltage needed to ionize the neon gas, the lamp suddenly acts like a short circuit.

That change lets the capacitor discharge, and the lamp flashes. After the capacitor fully discharges, the same cycle begins again. This repeated charge-and-discharge process creates a steady flashing effect. The time between flashes depends on the circuit time constant, which can be adjusted by changing the resistance R and capacitance C. By selecting different values, the flash frequency can be controlled.

Tube lights use another first-order circuit called an RL circuit, which contains a resistor and an inductor. In this case, the choke coil works as the inductor, and the wire resistance acts as the resistor. When voltage is applied, the choke resists a sudden rise in current and produces an electromotive force, or emf, that grows with the applied voltage. This emf helps ionize the gas in the tube light, so the lamp turns on.

For an RL circuit, the time constant is L divided by R, where L is inductance and R is resistance. This value shows how quickly the circuit responds to changes in the input signal. A larger time constant means a slower response, while a smaller one means a faster response.

First-Order Circuits in Flashing Lamps

first-order circuits

First-order circuits use a resistor and one energy storage element, either a capacitor or an inductor. They are common in electronic systems and are described by a first-order differential equation that links the input and output signals. One important example is the RC circuit, which uses a resistor and a capacitor. In a relaxation oscillator such as a neon lamp circuit, the capacitor starts charging when voltage is applied. At first, the lamp behaves like an open circuit. When the capacitor...

rc circuit without source

RC Capacitor Discharge After Power Loss

An RC circuit discharges after the DC source is removed. If the capacitor was fully charged first, its initial voltage, V0, provides the energy that drives the source-free circuit. Kirchhoff’s current law is applied at the top node of the circuit. The current terms for the resistor and capacitor are then substituted, which leads to a first-order differential equation. Rearranging, integrating, and taking the exponential gives the natural response of the circuit. The integration constant in...

rc circuit with source

RC Circuit Charging After a DC Step

An RC circuit with a DC source shows how a capacitor charges after a sudden voltage step. The applied source is treated as a unit step function, and the capacitor voltage is the step response of the circuit. This response describes how the circuit reacts right after the input changes. A capacitor cannot change its voltage instantly. So, immediately after the switch closes at t=0, the capacitor voltage stays at its initial value. Kirchhoff’s current law is then applied at that moment and...

rl circuit without source

RL Circuit Decay After Source Removal

An RL circuit begins to decay after the DC source is removed. At that moment, the circuit becomes source-free. If the inductor has an initial current, I0, it also stores initial energy. That stored energy drives the natural response of the circuit. Kirchhoff’s voltage law is applied around the loop. The inductor voltage and resistor voltage are substituted into the equation. This gives a first-order differential equation for the current. Rearranging the terms produces a logarithmic form, which...

rl circuit with source

RL Step Response Under a DC Source

An RL circuit connected to a DC source has a step response that changes over time. The response has two parts: the transient response and the steady-state response. The transient response is the short-lived reaction that happens right after the source is applied. During the transient phase, the current changes exponentially. If the circuit starts with current in the inductor, that current decays toward zero as time goes on. At this stage, the inductor acts like a short circuit, so the source...

design example: frog muscle response

RL Circuit and Frog Leg Current Response

An RL circuit is used to model the frog leg’s response to electrical stimulation. In this setup, the student studies how current changes in a resistor-inductor circuit can trigger muscle contraction. The circuit provides a way to control and measure the electrical impulses involved in the experiment. When the switch is closed, the frog’s leg shows a brief contraction. At steady state, the inductor acts like a short circuit. That lets current bypass the resistor and produces a mild, short...

second-order circuits

RLC Damping and Resonant Frequency

Second-order circuits use two energy storage elements, such as a capacitor and an inductor, to shape how current and voltage change over time. These circuits include RLC circuits, along with RC and RL circuits that have two capacitors or two inductors. Their behavior is described by second-order differential equations that connect the input signal to the output signal. The input usually comes from a voltage source or a current source. The output is often the voltage across the capacitor, the...

series rlc circuit without source

Natural Response of a Source-Free RLC Circuit

A source-free RLC circuit is a series circuit with a resistor, inductor, and capacitor, but no external energy source. It begins with the energy already stored in the capacitor and inductor. That stored energy drives the circuit at first. The circuit is described by a second-order differential equation. This equation shows how the resistor, inductor, and capacitor interact over time. The resistor removes energy from the circuit, so the solution has an exponential form. When the exponential...

types of responses of series rlc circuits

types-of-responses-of-series-rlc-circuits

Damping in Series RLC Circuit Responses

A source-free series RLC circuit shows three response patterns based on damping. The circuit is described by a second-order differential equation. Its complete solution is made from two distinct solutions. Those solutions depend on the roots, which are written in terms of the damping factor and the resonant frequency. When the damping factor is greater than the resonant frequency, both roots are real and negative. This gives an overdamped response. The circuit output decays slowly over time. <br...

series rlc circuit with source

Forced Response in a Series RLC Circuit

A series RLC circuit with a DC source can model an automobile ignition system. The circuit shows how a battery can produce the high voltage needed for a spark. In this case, the input DC voltage acts like a forcing step function. Applying Kirchhoff's voltage law leads to a second-order differential equation. A second-order differential equation is an equation with a term for the second derivative. The form of this equation is very similar to the one used for a source-free RLC circuit, so the...

parallel rlc circuits

Parallel RLC Step Response in Surge Protectors

Parallel RLC circuits help explain how a surge protector works in a street lamp. The circuit model uses a DC input source that creates a step response when the switch is turned on. This setup shows how the lamp’s components can be protected from sudden voltage spikes. When the switch closes, Kirchhoff’s current law is applied to the parallel RLC circuit. That leads to a second-order differential equation. The solution has two parts: a transient response and a steady-state response. The...

second-order op amp circuits

Second-Order Op Amp Low-Pass Filters

Second-order op-amp low-pass filters remove unwanted high-frequency noise from audio signals. They are used in audio systems to refine sound quality. These filters are often built as voltage followers and have two nodes with storage elements. The circuit analysis follows the same basic method used for second-order RLC circuits. In practice, bulky inductors are usually avoided because of their size and weight. For that reason, the focus here is on RC second-order op-amp circuits, which are...

design example: underdamped parallel rlc circuit

design-example-underdamped-parallel-rlc-circuit

Oscillator Design with a Parallel RLC Circuit

A parallel RLC circuit can be designed to work as an oscillator with underdamped behavior. This example targets a damped natural frequency of 4 kHz and a damping factor of 4 radians per second. A fixed resistance of 200 Ω is used as the starting point for the design. The first step is to find the capacitance. The damping factor is the reciprocal of twice the product of resistance and capacitance. Using that relationship, the needed capacitance value can be calculated from the given resistance...

key terms and concepts

Explore RC and RL first-order circuits through neon lamps and tube lights. Learn how time constant, resistance, capacitance, and inductance control circuit response.

First-Order Circuits in Flashing Lamps | JoVE K12

JoVE Core Electrical Engineering offers easy-to-understand animated videos that cover fundamental concepts of electric circuits along with circuit analysis techniques. It incorporates first-order and second-order circuits using operational amplifiers and circuit transformation concepts. The inclusion of practical design examples and real-world applications through scientist-in-action videos adds significant educational value, making complex concepts accessible.

electrical engineering

First-Order Circuits in Flashing Lamps

Description

Transcript

Tags