Name: zener diode voltage regulation
Uploaded: 2024-07-08T13:20:19.000Z
Duration: 1 min 16 s
Channel: JoVE

与普通二极管类似，齐纳二极管在正向偏置时允许电流通过，在反向偏置时则阻断电流。
然而，如果反向偏置电压超过齐纳二极管的反向击穿电压，电流将流过该二极管。齐纳二极管的典型击穿电压范围从几伏到几百伏不等。
在反向偏置工作状态下，特别是超过拐点电流后，齐纳二极管表现出几乎垂直的电流-电压特性。
随着源电压的增加，流过齐纳二极管的电流增大，但其两端的电压保持不变。
反向偏置下 I-V 特性曲线的斜率定义为齐纳二极管微分电阻的倒数。
当通过齐纳二极管的电流偏离其规定值时，齐纳二极管两端的电压仅有轻微变化。因此，齐纳二极管被用作敏感电子设备中的电压调节器。
然而，当通过齐纳二极管的电流接近膝点电流时，这种电压偏移变得更加显著，因此齐纳二极管主要在大电流区域适合作为电压调节器使用。

齐纳二极管

Zener Diodes

齐纳二极管是一种的半导体器件，并设计为在反向击穿区域内工作，它们允许电流流入阴极，使其相对于阳极为正。这种反向操作能够将齐纳二极管与传统二极管区分开来，使其能够用于各种应用场景中，其中最显著的是用作电压调节器。齐纳二极管的一个显著的特点是它们在某个阈值电流（称为拐点电流）以上几乎垂直的 I-V（电流-电压）特性曲线，这使齐纳二极管能够在很宽的电流范围内保持相对稳定的电压。
制造商指定了齐纳二极管的最大功率耗散和其在特定测试电流下的齐纳电压。齐纳电压的范围可以从几伏到几百伏，并且会随着电流的变化而发生轻微变化。这种变化是由于二极管的动态电阻所引起的，动态电阻的定义是其在工作区域中 I-V 曲线斜率的倒数。低动态电阻对于在电流发生变化时能够保持电压的稳定性是至关重要的，这能够增强齐纳二极管在电压调节应用中的有效性。
然而，更加重要的是避免齐纳二极管在动态电阻显著增加的低电流区域中进行工作，因为这会导致调节电压变得不稳定。齐纳电压与温度之间的关系是另一个关键因素，温度系数（以毫伏/摄氏度来进行表示）表明了电压随温度的变化情况。低压齐纳二极管通常具有负温度系数，而高压二极管则具有正温度系数。这通常会应用到需要稳定的基准电压且温度影响最小的场景中，可以将具有正温度系数的齐纳二极管与正向导通二极管进行串联，并以此来有效的补偿其中的温度变化。

与普通二极管类似，齐纳二极管在正向偏置时允许电流通过，在反向偏置时阻断电流。  
然而，当反向偏置电压超过……时

Education

教育

JoVE Core

Electrical Engineering

电气工程

Unit 1

第一单元

Diodes

二极管

KEY TERMS AND CONCEPTS

关键术语与概念

zener diode voltage regulation

Zener diodes are semiconductor devices used to hold voltage steady in reverse bias. In reverse breakdown, current flows into the cathode and makes it positive relative to the anode. This behavior is different from a conventional diode and is the reason Zener diodes are useful in voltage regulation.

A Zener diode has a nearly vertical current-voltage, or I-V, curve above a threshold called the knee current. That shape lets it keep a fairly stable voltage over a wide range of currents. Manufacturers list the Zener voltage at a specific test current and also give the maximum power dissipation.

The Zener voltage can range from a few volts to several hundred volts. It changes slightly as current changes because the diode has dynamic resistance, which is the inverse of the slope of the I-V curve in the operating region. Low dynamic resistance helps the voltage stay stable, so the diode works better as a regulator.

It is important not to run a Zener diode in the low-current region. In that region, dynamic resistance rises a lot and the regulated voltage can become unstable. Temperature also affects Zener voltage, and the temperature coefficient, measured in millivolts per degree Celsius, shows how the voltage changes with temperature.

Lower-voltage Zener diodes usually have negative temperature coefficients. Higher-voltage Zener diodes usually have positive coefficients. For a more stable reference voltage, a Zener diode with a positive temperature coefficient can be connected in series with a forward-conducting diode to help cancel temperature changes.

Zener Diode Voltage Regulation

the ideal diode

Ideal Diode I-V Curve and Rectification

An ideal diode is a simple model of a semiconductor diode used to show how current moves through circuits. A diode has two terminals. The anode is positive, and the cathode is negative. In this model, current can flow only in one direction. When a positive voltage is applied to the anode relative to the cathode, the diode is forward-biased. In that state, it conducts current. When the cathode is at a higher potential than the anode, the diode is reverse-biased. It then blocks current and acts...

diode: forward bias

Diode Current in Forward Bias

Diode current in forward bias depends on how the p-type and n-type regions are connected to a battery. When the p-type region is tied to the positive terminal and the n-type region to the negative terminal, the diode is forward-biased. This setup lowers the potential barrier inside the diode and lets current move easily from the p-type side to the n-type side. The current-voltage behavior of a forward-biased diode is described by its I-V characteristics. These characteristics depend on the...

diode: reverse bias

Diode Reverse Current and Breakdown

A diode in reverse bias blocks current flow and widens its depletion region. In this setup, the positive terminal of the power source connects to the n-type material, and the negative terminal connects to the p-type material. The reverse connection also raises the barrier potential, so current stays very small. The small reverse current is called leakage current. It comes mainly from minority charge carriers. At room temperature, once the reverse voltage is above the thermal voltage, the...

zener diodes

Zener diodes are semiconductor devices used to hold voltage steady in reverse bias. In reverse breakdown, current flows into the cathode and makes it positive relative to the anode. This behavior is different from a conventional diode and is the reason Zener diodes are useful in voltage regulation. A Zener diode has a nearly vertical current-voltage, or I-V, curve above a threshold called the knee current. That shape lets it keep a fairly stable voltage over a wide range of currents.

modeling of diode forward characteristics

modeling-of-diode-forward-characteristics

Diode Forward Bias: I-V Curve and Models

Diode forward bias is analyzed with the current-voltage, or I-V, curve and two common circuit models. These models help describe how a diode behaves when current flows in the forward direction. They are useful for electronic circuit design and analysis. The exponential diode model is used when the source voltage rises above 0.5 volts. At that point, the diode current increases exponentially above the saturation current. The I-V curve shows this nonlinear response as the forward voltage...

small-signal diode model

Diode Bias and Small-Signal Response

Diode bias and small-signal response describe how a diode behaves when a steady DC voltage and a tiny changing signal act on the same circuit. The DC bias sets the diode’s operating point, or Q point. Around that point, the diode current and voltage follow an exponential I-V relationship. A small time-varying signal can be added on top of the DC bias to study how the diode responds to small changes. When the signal voltage is much smaller than the thermal voltage, the diode’s behavior can be...

modeling of diode reverse characteristics

modeling-of-diode-reverse-characteristics

Zener Diode Load-Line Modeling

Zener diode load-line modeling shows how a reverse-biased diode sets a steady voltage in a circuit. Zener diodes use reverse breakdown in a controlled way, so they can hold a fixed voltage across their terminals. This makes them useful for voltage regulation. When the reverse voltage rises above the Zener voltage, or VZ, the diode enters the breakdown region. In this region, the current-voltage, or I-V, curve becomes nearly vertical after the knee current, IZ, is reached. That means the...

half wave rectifier

Single-Diode AC to DC Conversion

Single-diode AC to DC conversion uses a half-wave rectifier to change alternating current into a unidirectional voltage. The circuit is simple. It uses one diode in series with a load resistor and an AC power source. The diode controls the current because it allows flow in only one direction. During the positive half-cycles of the AC input, the diode is forward-biased. When the input voltage is greater than the diode threshold, current flows and an output voltage appears across the load...

full wave rectifier

AC to DC Conversion with Full-Wave Rectifiers

A full-wave rectifier converts alternating current, or AC, into direct current, or DC. It is more efficient than a half-wave rectifier. The circuit usually uses a center-tapped transformer, two diodes, and a load resistor. The center-tapped transformer is the key part of the circuit. Its secondary winding is split into two equal voltages with opposite polarities. That split lets the rectifier use both halves of the AC input waveform. During the positive half-cycle of the AC signal, diode D1...

bridge rectifier

AC to DC Conversion with Bridge Diodes

A bridge rectifier converts alternating current (AC) into direct current (DC) using four diodes arranged in a bridge layout. It is used to turn both halves of the AC waveform into a single-direction output. That makes it an important part of many electronics circuits. During the positive half-cycle, diodes D1 and D2 conduct. Current then flows through the load resistor R. At the same time, D3 and D4 are reverse-biased, so they do not conduct. The action switches during the negative half-cycle.

clipper circuit

Dual Diode Wave Clipping

Dual diode wave clipping uses diodes and biasing batteries to reshape an AC signal. A clipper circuit is a wave-shaping device that changes waveform parts without changing the whole signal. It is commonly used in television and radar communication systems to improve waveform modulation in transmitters and receivers. A dual-clipper setup uses two ideal diodes, two biasing batteries, and a resistor connected in parallel. The circuit works by responding to the phase of the input AC signal. The...

clamper circuit

DC Restorer for Waveform Level Shifting

A clamper circuit, or DC restorer, shifts a waveform up or down by adding a DC level. It is a special form of rectifier circuit. In this setup, the output is taken across the diode instead of across the capacitor. The circuit works well with square wave inputs and other pulse signals. The diode direction lets the capacitor charge to the most negative peak of the input signal. After that, the diode stops conducting. The capacitor then holds that voltage at a steady value. As a result, the...

voltage doubler circuit

How a Voltage Doubler Raises AC Output

A voltage doubler circuit raises the output voltage by using a clamping section and a rectifier section. The clamping section includes a capacitor, C1, and a diode, D1. The rectifier section includes a second diode, D2, and a capacitor, C2. The circuit starts working when a sinusoidal input signal enters the clamping section. Under ideal conditions, this stage clamps the positive peaks at zero volts. It also lets the negative peak reach a magnitude that is twice the input amplitude. That...

schottky barrier diode

Fast Switching in Schottky Diodes

Schottky barrier diodes use a metal-semiconductor junction to control current flow. They are built by combining a metal layer with a moderately doped n-type semiconductor. This contact creates the Schottky barrier, which gives the diode its one-way current behavior. When the metal touches the semiconductor, charge transfer occurs. The Fermi levels of the two materials align, and a depletion region forms near the contact area. In an n-type semiconductor, this region contains uncompensated...

key terms and concepts

Explore how Zener diodes hold voltage steady in reverse breakdown, why dynamic resistance matters, and how temperature affects their use in regulation.

Zener Diode Voltage Regulation | JoVE K12

JoVE Core Electrical Engineering offers easy-to-understand animated videos that cover fundamental concepts of electric circuits along with circuit analysis techniques. It incorporates first-order and second-order circuits using operational amplifiers and circuit transformation concepts. The inclusion of practical design examples and real-world applications through scientist-in-action videos adds significant educational value, making complex concepts accessible.

electrical engineering

Zener Diode Voltage Regulation

Description

Transcript