Name: diode bias and small-signal response
Uploaded: 2024-07-08T13:20:19.000Z
Duration: 1 min 18 s
Channel: JoVE

在二极管电路中，直流偏置电压通过电阻驱动二极管电流，在电流-电压特性曲线上表现出指数行为。
当引入一个微小的时变信号时，该信号会与围绕静态工作点（Q 点）的直流偏置电压叠加。
总瞬时二极管电流中的指数项对偏置电流和信号电流均有贡献。
如果信号电压的幅度明显小于热电压，则二极管工作在特性曲线的一个较短且近乎线性的区间内。
在此小信号近似条件下，指数项得以简化。
因此，二极管电流变为直流偏置电流与信号电流之和。
二极管的小信号电导定义为小信号电流与小信号电压之比，由电流-电压特性曲线上某点切线的斜率确定 我-V 曲线在 Q 点。
二极管小信号电导的倒数称为二极管小信号电阻或增量电阻，其值等于热电压除以偏置电流。

小信号二极管模型

Small-signal Diode Model

在分析电路中二极管的行为时，流过二极管的电流与跨二极管的电压之间的关系尤其令人感兴趣，尤其是在考虑直流 (DC) 偏置电压的影响时。施加直流偏置时，该偏置会影响二极管的工作点（称为 Q 点），二极管的电流-电压 (I-V) 特性在此点附近呈现指数行为。在此偏置之上引入一个小的时变信号有助于检查二极管对此 Q 点附近波动的响应。
<img alt="Figure 1" src="/files/ftp_upload/15717/15717_Figure_1.svg" style="text-align: center; height: 250px;">
当此额外信号电压的幅度保持远小于二极管的热电压 (V_T) 时，二极管的响应可在其特性曲线的短段上近似为线性。这种情形称为小信号近似，它将复杂的指数关系简化为更易于管理的线性关系，允许将总瞬时二极管电流 (i_D) 视为恒定偏置电流 i_D(DC) 和变化信号电流 i_D(AC) 的总和
<img alt="Equation 1" src="/files/ftp_upload/15717/15717_Equation_1.svg" style="text-align: center; height: 24px;">
将信号电流与信号电压联系起来的测量值以电导表示，以姆欧为单位，称为二极管小信号电导。它是 Q 点处 I-V 曲线切线的斜率。相反，二极管的小信号或增量电阻 (r_d) 是其电导的倒数。它测量二极管对电流微小变化的阻力，通过将热电压除以偏置电流来计算。
<img alt="Equation 2" src="/files/ftp_upload/15717/15717_Equation_2.svg" style="text-align: center; height: 46px;">
<img alt="Equation 3" src="/files/ftp_upload/15717/15717_Equation_3.svg" style="text-align: center; height: 46px;">
这些参数对于设计和分析涉及二极管的电路至关重要，特别是在需要精确控制信号放大或衰减的应用中。

在二极管电路中，直流偏置电压通过电阻驱动二极管电流，在电流-电压特性中表现出指数行为……

Education

教育

JoVE Core

Electrical Engineering

电气工程

Unit 1

第一单元

Diodes

二极管

KEY TERMS AND CONCEPTS

关键术语与概念

diode bias and small-signal response

Diode bias and small-signal response describe how a diode behaves when a steady DC voltage and a tiny changing signal act on the same circuit. The DC bias sets the diode’s operating point, or Q point. Around that point, the diode current and voltage follow an exponential I-V relationship.

A small time-varying signal can be added on top of the DC bias to study how the diode responds to small changes. When the signal voltage is much smaller than the thermal voltage, the diode’s behavior can be treated as linear over a short part of its curve. This is called the small-signal approximation.

With this approximation, the total diode current can be written as the sum of a constant DC part and a varying AC part. The signal current is linked to the signal voltage by the diode small-signal conductance, which is measured in mhos. This conductance is the slope of the tangent to the I-V curve at the Q point.

The inverse of conductance is the diode’s small-signal, or incremental, resistance, r d. It shows how much the diode resists small changes in current. It is found by dividing the thermal voltage by the bias current. These ideas are useful when analyzing and designing circuits that use diodes for signal amplification or attenuation.

Diode Bias and Small-Signal Response

the ideal diode

Ideal Diode I-V Curve and Rectification

An ideal diode is a simple model of a semiconductor diode used to show how current moves through circuits. A diode has two terminals. The anode is positive, and the cathode is negative. In this model, current can flow only in one direction. When a positive voltage is applied to the anode relative to the cathode, the diode is forward-biased. In that state, it conducts current. When the cathode is at a higher potential than the anode, the diode is reverse-biased. It then blocks current and acts...

diode: forward bias

Diode Current in Forward Bias

Diode current in forward bias depends on how the p-type and n-type regions are connected to a battery. When the p-type region is tied to the positive terminal and the n-type region to the negative terminal, the diode is forward-biased. This setup lowers the potential barrier inside the diode and lets current move easily from the p-type side to the n-type side. The current-voltage behavior of a forward-biased diode is described by its I-V characteristics. These characteristics depend on the...

diode: reverse bias

Diode Reverse Current and Breakdown

A diode in reverse bias blocks current flow and widens its depletion region. In this setup, the positive terminal of the power source connects to the n-type material, and the negative terminal connects to the p-type material. The reverse connection also raises the barrier potential, so current stays very small. The small reverse current is called leakage current. It comes mainly from minority charge carriers. At room temperature, once the reverse voltage is above the thermal voltage, the...

zener diodes

Zener Diode Voltage Regulation

Zener diodes are semiconductor devices used to hold voltage steady in reverse bias. In reverse breakdown, current flows into the cathode and makes it positive relative to the anode. This behavior is different from a conventional diode and is the reason Zener diodes are useful in voltage regulation. A Zener diode has a nearly vertical current-voltage, or I-V, curve above a threshold called the knee current. That shape lets it keep a fairly stable voltage over a wide range of currents.

modeling of diode forward characteristics

modeling-of-diode-forward-characteristics

Diode Forward Bias: I-V Curve and Models

Diode forward bias is analyzed with the current-voltage, or I-V, curve and two common circuit models. These models help describe how a diode behaves when current flows in the forward direction. They are useful for electronic circuit design and analysis. The exponential diode model is used when the source voltage rises above 0.5 volts. At that point, the diode current increases exponentially above the saturation current. The I-V curve shows this nonlinear response as the forward voltage...

small-signal diode model

Diode bias and small-signal response describe how a diode behaves when a steady DC voltage and a tiny changing signal act on the same circuit. The DC bias sets the diode’s operating point, or Q point. Around that point, the diode current and voltage follow an exponential I-V relationship. A small time-varying signal can be added on top of the DC bias to study how the diode responds to small changes. When the signal voltage is much smaller than the thermal voltage, the diode’s behavior can be...

modeling of diode reverse characteristics

modeling-of-diode-reverse-characteristics

Zener Diode Load-Line Modeling

Zener diode load-line modeling shows how a reverse-biased diode sets a steady voltage in a circuit. Zener diodes use reverse breakdown in a controlled way, so they can hold a fixed voltage across their terminals. This makes them useful for voltage regulation. When the reverse voltage rises above the Zener voltage, or VZ, the diode enters the breakdown region. In this region, the current-voltage, or I-V, curve becomes nearly vertical after the knee current, IZ, is reached. That means the...

half wave rectifier

Single-Diode AC to DC Conversion

Single-diode AC to DC conversion uses a half-wave rectifier to change alternating current into a unidirectional voltage. The circuit is simple. It uses one diode in series with a load resistor and an AC power source. The diode controls the current because it allows flow in only one direction. During the positive half-cycles of the AC input, the diode is forward-biased. When the input voltage is greater than the diode threshold, current flows and an output voltage appears across the load...

full wave rectifier

AC to DC Conversion with Full-Wave Rectifiers

A full-wave rectifier converts alternating current, or AC, into direct current, or DC. It is more efficient than a half-wave rectifier. The circuit usually uses a center-tapped transformer, two diodes, and a load resistor. The center-tapped transformer is the key part of the circuit. Its secondary winding is split into two equal voltages with opposite polarities. That split lets the rectifier use both halves of the AC input waveform. During the positive half-cycle of the AC signal, diode D1...

bridge rectifier

AC to DC Conversion with Bridge Diodes

A bridge rectifier converts alternating current (AC) into direct current (DC) using four diodes arranged in a bridge layout. It is used to turn both halves of the AC waveform into a single-direction output. That makes it an important part of many electronics circuits. During the positive half-cycle, diodes D1 and D2 conduct. Current then flows through the load resistor R. At the same time, D3 and D4 are reverse-biased, so they do not conduct. The action switches during the negative half-cycle.

clipper circuit

Dual Diode Wave Clipping

Dual diode wave clipping uses diodes and biasing batteries to reshape an AC signal. A clipper circuit is a wave-shaping device that changes waveform parts without changing the whole signal. It is commonly used in television and radar communication systems to improve waveform modulation in transmitters and receivers. A dual-clipper setup uses two ideal diodes, two biasing batteries, and a resistor connected in parallel. The circuit works by responding to the phase of the input AC signal. The...

clamper circuit

DC Restorer for Waveform Level Shifting

A clamper circuit, or DC restorer, shifts a waveform up or down by adding a DC level. It is a special form of rectifier circuit. In this setup, the output is taken across the diode instead of across the capacitor. The circuit works well with square wave inputs and other pulse signals. The diode direction lets the capacitor charge to the most negative peak of the input signal. After that, the diode stops conducting. The capacitor then holds that voltage at a steady value. As a result, the...

voltage doubler circuit

How a Voltage Doubler Raises AC Output

A voltage doubler circuit raises the output voltage by using a clamping section and a rectifier section. The clamping section includes a capacitor, C1, and a diode, D1. The rectifier section includes a second diode, D2, and a capacitor, C2. The circuit starts working when a sinusoidal input signal enters the clamping section. Under ideal conditions, this stage clamps the positive peaks at zero volts. It also lets the negative peak reach a magnitude that is twice the input amplitude. That...

schottky barrier diode

Fast Switching in Schottky Diodes

Schottky barrier diodes use a metal-semiconductor junction to control current flow. They are built by combining a metal layer with a moderately doped n-type semiconductor. This contact creates the Schottky barrier, which gives the diode its one-way current behavior. When the metal touches the semiconductor, charge transfer occurs. The Fermi levels of the two materials align, and a depletion region forms near the contact area. In an n-type semiconductor, this region contains uncompensated...

key terms and concepts

Learn how DC bias sets a diode Q point and how small AC signals can be modeled with conductance and incremental resistance for circuit analysis.

Diode Bias and Small-Signal Response | JoVE K12

JoVE Core Electrical Engineering offers easy-to-understand animated videos that cover fundamental concepts of electric circuits along with circuit analysis techniques. It incorporates first-order and second-order circuits using operational amplifiers and circuit transformation concepts. The inclusion of practical design examples and real-world applications through scientist-in-action videos adds significant educational value, making complex concepts accessible.

electrical engineering

Diode Bias and Small-Signal Response

Description

Transcript

Tags