Name: second-order op amp low-pass filters
Uploaded: 2024-04-11T12:48:44.000Z
Duration: 1 min 19 s
Channel: JoVE

Stellen Sie sich ein Audiosystem vor, das einen Tiefpassfilter zweiter Ordnung verwendet, um das unerwünschte hochfrequente Rauschen im Audiosignal zu eliminieren.
Dieser Aufbau umfasst eine Operationsverstärkerschaltung zweiter Ordnung mit einer Spannungsfolgerkonfiguration und zwei Knoten, die aus zwei Speicherelementen bestehen.
Wendet man das aktuelle Kirchhoffsche Gesetz auf diese Knoten an, so erhält man zwei Differentialgleichungen.
Zusätzlich entspricht die Spannung am Rückkopplungskondensator der Spannung des Widerstands abzüglich der Spannung des anderen Kondensators.
Diese Gleichungen können verwendet werden, um die Kondensatorspannungen aus der KCL-Gleichung am ersten Knoten zu eliminieren.
Das Ergebnis ist eine charakteristische Differentialgleichung zweiter Ordnung.
Die Lösung dieser Differentialgleichung umfasst sowohl transiente als auch stationäre Antworten.
Das Einschwingverhalten verschwindet mit der Zeit und ähnelt der Lösung für quellenfreie Schaltungen in überdämpften, unterdämpften und kritisch gedämpften Szenarien.
Wenn die Schaltung einen stationären Zustand erreicht, fließt kein Strom durch die Kondensatoren oder Widerstände, und die Eingangsanschlüsse des idealen Operationsverstärkers verhindern den Stromzufluss. Infolgedessen stimmt das stationäre Verhalten mit der Quellenspannung überein.
Der Wegfall der Eingangsquellenspannung führt zu einem reinen Einschwingverhalten.

Es wurden keine Interessenkonflikte angegeben.

operationsverstärkerschaltungen zweiter ordnung

Die Implementierung von Tiefpassfiltern zweiter Ordnung in Audiosystemen ist entscheidend für die Verfeinerung von Audiosignalen durch die Eliminierung unerwünschter hochfrequenter Störungen. Bei diesen Filtern handelt es sich typischerweise um Operationsverstärkerschaltungen zweiter Ordnung, die als Spannungsfolger konfiguriert sind und zwei Knoten mit unterschiedlichen Speicherelementen umfassen. Die Analyse solcher Schaltkreise folgt einem systematischen Ansatz, ähnlich den RLC-Schaltkreisen zweiter Ordnung. In der Praxis werden sperrige Induktoren aufgrund ihrer Größe und ihres Gewichts selten eingesetzt. Dies bedeutet, dass der Schwerpunkt hier hauptsächlich auf RC-Operationsverstärkerschaltungen zweiter Ordnung liegt, die umfangreiche Anwendungen in Geräten wie Filtern und Oszillatoren haben. Nach Anwendung des Kirchhoffschen Stromgesetzes auf die Knoten ergeben sich zwei Differentialgleichungen. Darüber hinaus wird eine charakteristische Differentialgleichung zweiter Ordnung durch Beobachtung der Spannungsverhältnisse zwischen den Schaltungskomponenten abgeleitet. Diese Gleichung verkörpert sowohl transiente als auch stationäre Reaktionen. <img alt="Equation1" src="/files/ftp_upload/15103/15103_PT_Equation_1.svg" style="text-align: center; height: 34px;"> Das Einschwingverhalten lässt mit der Zeit allmählich nach und ähnelt den Lösungen, die in quellenfreien Schaltkreisen gefunden werden, wobei es Merkmale von überdämpften, unterdämpften und kritisch gedämpften Szenarien aufweist. Sobald die Schaltung einen stabilen Zustand erreicht, leiten die Kondensatoren und Widerstände keinen Strom mehr und die idealen Eingangsanschlüsse des Operationsverstärkers blockieren den Stromfluss. Folglich entspricht die stationäre Reaktion der Quellenspannung. Insbesondere führt die Eliminierung der Eingangsquellenspannung zu einem reinen Einschwingverhalten. Diese Operationsverstärkerschaltungen zweiter Ordnung finden vielfältige Anwendungsmöglichkeiten bei der Verbesserung der Audioqualität und sind in verschiedenen Audioverarbeitungssystemen von entscheidender Bedeutung. Das Verständnis ihres Verhaltens unter verschiedenen Dämpfungsszenarien hilft dabei, eine optimale Audiosignalverfeinerung zu erreichen.

Operationsverstärkerschaltungen zweiter Ordnung

Stellen Sie sich ein Audiosystem vor, das einen Tiefpassfilter zweiter Ordnung verwendet, um das unerwünschte hochfrequente Rauschen im Audiosignal zu eliminieren.
Dieses Setup ...

Education

Lehre

JoVE Core

Electrical Engineering

Elektrotechnik

Unit 1

Einheit 1

First and Second-Order Circuits

Schaltungen erster und zweiter Ordnung

KEY TERMS AND CONCEPTS

KERNBEGRIFFE UND KONZEPTE

Second-order Op Amp Circuits

second-order op amp low-pass filters

Second-order op-amp low-pass filters remove unwanted high-frequency noise from audio signals. They are used in audio systems to refine sound quality. These filters are often built as voltage followers and have two nodes with storage elements.

The circuit analysis follows the same basic method used for second-order RLC circuits. In practice, bulky inductors are usually avoided because of their size and weight. For that reason, the focus here is on RC second-order op-amp circuits, which are common in filters and oscillators.

Applying Kirchhoff's current law at the nodes gives two differential equations. A second-order characteristic differential equation is then found from the voltage relationships across the circuit parts. That equation describes both the transient response and the steady-state response.

The transient response fades over time. It can show overdamped, underdamped, or critically damped behavior, much like the solutions for source-free circuits. When the circuit reaches steady state, the capacitors and resistors no longer carry current, and the ideal op-amp input terminals block current flow. As a result, the steady-state response matches the source voltage.

If the input source voltage is removed, the circuit shows a pure transient response. These second-order op-amp circuits are important in audio processing systems because they help improve audio quality. Knowing how the circuit behaves under different damping conditions helps explain how the filter shapes the signal.

Second-Order Op Amp Low-Pass Filters

first-order circuits

First-Order Circuits in Flashing Lamps

First-order circuits use a resistor and one energy storage element, either a capacitor or an inductor. They are common in electronic systems and are described by a first-order differential equation that links the input and output signals. One important example is the RC circuit, which uses a resistor and a capacitor. In a relaxation oscillator such as a neon lamp circuit, the capacitor starts charging when voltage is applied. At first, the lamp behaves like an open circuit. When the capacitor...

rc circuit without source

RC Capacitor Discharge After Power Loss

An RC circuit discharges after the DC source is removed. If the capacitor was fully charged first, its initial voltage, V0, provides the energy that drives the source-free circuit. Kirchhoff’s current law is applied at the top node of the circuit. The current terms for the resistor and capacitor are then substituted, which leads to a first-order differential equation. Rearranging, integrating, and taking the exponential gives the natural response of the circuit. The integration constant in...

rc circuit with source

RC Circuit Charging After a DC Step

An RC circuit with a DC source shows how a capacitor charges after a sudden voltage step. The applied source is treated as a unit step function, and the capacitor voltage is the step response of the circuit. This response describes how the circuit reacts right after the input changes. A capacitor cannot change its voltage instantly. So, immediately after the switch closes at t=0, the capacitor voltage stays at its initial value. Kirchhoff’s current law is then applied at that moment and...

rl circuit without source

RL Circuit Decay After Source Removal

An RL circuit begins to decay after the DC source is removed. At that moment, the circuit becomes source-free. If the inductor has an initial current, I0, it also stores initial energy. That stored energy drives the natural response of the circuit. Kirchhoff’s voltage law is applied around the loop. The inductor voltage and resistor voltage are substituted into the equation. This gives a first-order differential equation for the current. Rearranging the terms produces a logarithmic form, which...

rl circuit with source

RL Step Response Under a DC Source

An RL circuit connected to a DC source has a step response that changes over time. The response has two parts: the transient response and the steady-state response. The transient response is the short-lived reaction that happens right after the source is applied. During the transient phase, the current changes exponentially. If the circuit starts with current in the inductor, that current decays toward zero as time goes on. At this stage, the inductor acts like a short circuit, so the source...

design example: frog muscle response

RL Circuit and Frog Leg Current Response

An RL circuit is used to model the frog leg’s response to electrical stimulation. In this setup, the student studies how current changes in a resistor-inductor circuit can trigger muscle contraction. The circuit provides a way to control and measure the electrical impulses involved in the experiment. When the switch is closed, the frog’s leg shows a brief contraction. At steady state, the inductor acts like a short circuit. That lets current bypass the resistor and produces a mild, short...

second-order circuits

RLC Damping and Resonant Frequency

Second-order circuits use two energy storage elements, such as a capacitor and an inductor, to shape how current and voltage change over time. These circuits include RLC circuits, along with RC and RL circuits that have two capacitors or two inductors. Their behavior is described by second-order differential equations that connect the input signal to the output signal. The input usually comes from a voltage source or a current source. The output is often the voltage across the capacitor, the...

series rlc circuit without source

Natural Response of a Source-Free RLC Circuit

A source-free RLC circuit is a series circuit with a resistor, inductor, and capacitor, but no external energy source. It begins with the energy already stored in the capacitor and inductor. That stored energy drives the circuit at first. The circuit is described by a second-order differential equation. This equation shows how the resistor, inductor, and capacitor interact over time. The resistor removes energy from the circuit, so the solution has an exponential form. When the exponential...

types of responses of series rlc circuits

types-of-responses-of-series-rlc-circuits

Damping in Series RLC Circuit Responses

A source-free series RLC circuit shows three response patterns based on damping. The circuit is described by a second-order differential equation. Its complete solution is made from two distinct solutions. Those solutions depend on the roots, which are written in terms of the damping factor and the resonant frequency. When the damping factor is greater than the resonant frequency, both roots are real and negative. This gives an overdamped response. The circuit output decays slowly over time. <br...

series rlc circuit with source

Forced Response in a Series RLC Circuit

A series RLC circuit with a DC source can model an automobile ignition system. The circuit shows how a battery can produce the high voltage needed for a spark. In this case, the input DC voltage acts like a forcing step function. Applying Kirchhoff's voltage law leads to a second-order differential equation. A second-order differential equation is an equation with a term for the second derivative. The form of this equation is very similar to the one used for a source-free RLC circuit, so the...

parallel rlc circuits

Parallel RLC Step Response in Surge Protectors

Parallel RLC circuits help explain how a surge protector works in a street lamp. The circuit model uses a DC input source that creates a step response when the switch is turned on. This setup shows how the lamp’s components can be protected from sudden voltage spikes. When the switch closes, Kirchhoff’s current law is applied to the parallel RLC circuit. That leads to a second-order differential equation. The solution has two parts: a transient response and a steady-state response. The...

second-order op amp circuits

Second-order op-amp low-pass filters remove unwanted high-frequency noise from audio signals. They are used in audio systems to refine sound quality. These filters are often built as voltage followers and have two nodes with storage elements. The circuit analysis follows the same basic method used for second-order RLC circuits. In practice, bulky inductors are usually avoided because of their size and weight. For that reason, the focus here is on RC second-order op-amp circuits, which are...

design example: underdamped parallel rlc circuit

design-example-underdamped-parallel-rlc-circuit

Oscillator Design with a Parallel RLC Circuit

A parallel RLC circuit can be designed to work as an oscillator with underdamped behavior. This example targets a damped natural frequency of 4 kHz and a damping factor of 4 radians per second. A fixed resistance of 200 Ω is used as the starting point for the design. The first step is to find the capacitance. The damping factor is the reciprocal of twice the product of resistance and capacitance. Using that relationship, the needed capacitance value can be calculated from the given resistance...

key terms and concepts

Learn how second-order op-amp low-pass filters reduce audio noise, form characteristic equations, and show damping behavior in RC circuits.

Second-Order Op Amp Low-Pass Filters | JoVE K12

JoVE Core Electrical Engineering offers easy-to-understand animated videos that cover fundamental concepts of electric circuits along with circuit analysis techniques. It incorporates first-order and second-order circuits using operational amplifiers and circuit transformation concepts. The inclusion of practical design examples and real-world applications through scientist-in-action videos adds significant educational value, making complex concepts accessible.

electrical engineering

Second-Order Op Amp Low-Pass Filters

Description

Transcript

Tags