Name: oscillator design with a parallel rlc circuit
Uploaded: 2024-04-11T12:48:44.000Z
Duration: 1 min 17 s
Channel: JoVE

Los circuitos RLC paralelos con amortiguación insuficiente pueden soportar oscilaciones a una frecuencia de resonancia, lo que los hace adecuados para su uso en osciladores.
Un ingeniero eléctrico tiene la tarea de diseñar un modelo de circuito oscilador con una frecuencia natural amortiguada de 4 kilohercios y un factor de amortiguación de 4 radianes por segundo.
Con una resistencia establecida de 200 ohmios, se pueden determinar los valores precisos de capacitancia e inductancia.
Dado que el factor de amortiguamiento para el circuito es el recíproco del doble del producto de la resistencia y la capacitancia, se obtiene el valor de capacitancia requerido para el diseño del circuito.
La expresión matemática que correlaciona la frecuencia de resonancia, el factor de amortiguamiento y la frecuencia natural amortiguada se utiliza para obtener la frecuencia de resonancia.
La frecuencia de resonancia es inversamente proporcional a la raíz cuadrada del producto de la inductancia y la capacitancia.
Los valores conocidos se sustituyen en esta ecuación para obtener la inductancia requerida.
La frecuencia natural amortiguada es más baja que la frecuencia de resonancia y el valor de inductancia es menos de cuatro veces el cuadrado de la resistencia multiplicado por la capacitancia. Ambas condiciones confirman una oscilación subamortiguada.

No se han declarado conflictos de interés.

ejemplo de diseño: circuito rlc paralelo

Considere diseñar un circuito oscilador, un componente crucial en varios dispositivos y sistemas electrónicos. El objetivo es crear un circuito oscilador con características específicas: una frecuencia natural amortiguada de 4 kHz y un factor de amortiguación de 4 radianes por segundo. Para lograr esto, se emplea un circuito RLC paralelo, conocido por su capacidad para sostener oscilaciones a una frecuencia resonante. En este caso, el factor de amortiguación es fundamental para lograr el rendimiento deseado. Partiendo de una resistencia fija de 200 Ω, se determinan los valores necesarios de capacitancia e inductancia para cumplir con las especificaciones. Primero, se reconoce que el factor de amortiguamiento es el recíproco del doble del producto de la resistencia y la capacitancia. Esta información permite determinar con precisión el valor de capacitancia requerido para el circuito. <img alt="Equation1" src="/files/ftp_upload/15175/15175_PT_Equation_1.svg" style="text-align: center; height: 28px;"> A continuación, se centra la atención en la expresión matemática que conecta la frecuencia resonante, el factor de amortiguación y la frecuencia natural amortiguada. Manipulando esta ecuación, se puede extraer información de frecuencia resonante. <img alt="Equation2" src="/files/ftp_upload/15175/15175_PT_Equation_2.svg" style="text-align: center; height: 18px;"> La frecuencia de resonancia, crucial para el diseño de osciladores, es inversamente proporcional a la raíz cuadrada del producto de la inductancia y la capacitancia. Armado con este conocimiento y los valores conocidos, se calcula la inductancia necesaria para cumplir con los criterios de diseño. <img alt="Equation3" src="/files/ftp_upload/15175/15175_PT_Equation_3.svg" style="text-align: center; height: 34px;"> Estos cálculos confirman que la frecuencia natural amortiguada es efectivamente menor que la frecuencia resonante y el valor de la inductancia cae por debajo de cuatro veces el cuadrado de la resistencia multiplicada por la capacitancia. Estas condiciones afirman que el circuito oscilador ha sido diseñado para exhibir las oscilaciones subamortiguadas requeridas, lo que demuestra competencia en el diseño preciso del circuito.

Ejemplo de diseño: Circuito RLC paralelo

Los circuitos RLC paralelos con amortiguación insuficiente pueden soportar oscilaciones a una frecuencia de resonancia, lo que los hace adecuados para su uso en osciladores.
Un ingeniero eléctrico es ...

design-example-underdamped-parallel-rlc-circuit

Education

Educación

JoVE Core

Electrical Engineering

Ingeniería Eléctrica

Unit 1

Unidad 1

First and Second-Order Circuits

Circuitos de primer y segundo orden

KEY TERMS AND CONCEPTS

TÉRMINOS Y CONCEPTOS CLAVE

Design Example: Underdamped Parallel RLC Circuit

oscillator design with a parallel rlc circuit

A parallel RLC circuit can be designed to work as an oscillator with underdamped behavior. This example targets a damped natural frequency of 4 kHz and a damping factor of 4 radians per second. A fixed resistance of 200 Ω is used as the starting point for the design.

The first step is to find the capacitance. The damping factor is the reciprocal of twice the product of resistance and capacitance. Using that relationship, the needed capacitance value can be calculated from the given resistance and damping factor.

Next, the resonant frequency is found from the link between resonant frequency, damping factor, and damped natural frequency. Resonant frequency is important in oscillator design because it is the frequency a parallel RLC circuit tends to sustain. It is also tied to inductance and capacitance through the square root of their product.

With the capacitance known, the inductance is then computed from the resonant frequency equation. The results show that the damped natural frequency is lower than the resonant frequency. They also show that the inductance is below four times the square of the resistance multiplied by capacitance, which supports underdamped oscillations in the circuit.

Oscillator Design with a Parallel RLC Circuit

oscillator-design-with-a-parallel-rlc-circuit

first-order circuits

First-Order Circuits in Flashing Lamps

First-order circuits use a resistor and one energy storage element, either a capacitor or an inductor. They are common in electronic systems and are described by a first-order differential equation that links the input and output signals. One important example is the RC circuit, which uses a resistor and a capacitor. In a relaxation oscillator such as a neon lamp circuit, the capacitor starts charging when voltage is applied. At first, the lamp behaves like an open circuit. When the capacitor...

rc circuit without source

RC Capacitor Discharge After Power Loss

An RC circuit discharges after the DC source is removed. If the capacitor was fully charged first, its initial voltage, V0, provides the energy that drives the source-free circuit. Kirchhoff’s current law is applied at the top node of the circuit. The current terms for the resistor and capacitor are then substituted, which leads to a first-order differential equation. Rearranging, integrating, and taking the exponential gives the natural response of the circuit. The integration constant in...

rc circuit with source

RC Circuit Charging After a DC Step

An RC circuit with a DC source shows how a capacitor charges after a sudden voltage step. The applied source is treated as a unit step function, and the capacitor voltage is the step response of the circuit. This response describes how the circuit reacts right after the input changes. A capacitor cannot change its voltage instantly. So, immediately after the switch closes at t=0, the capacitor voltage stays at its initial value. Kirchhoff’s current law is then applied at that moment and...

rl circuit without source

RL Circuit Decay After Source Removal

An RL circuit begins to decay after the DC source is removed. At that moment, the circuit becomes source-free. If the inductor has an initial current, I0, it also stores initial energy. That stored energy drives the natural response of the circuit. Kirchhoff’s voltage law is applied around the loop. The inductor voltage and resistor voltage are substituted into the equation. This gives a first-order differential equation for the current. Rearranging the terms produces a logarithmic form, which...

rl circuit with source

RL Step Response Under a DC Source

An RL circuit connected to a DC source has a step response that changes over time. The response has two parts: the transient response and the steady-state response. The transient response is the short-lived reaction that happens right after the source is applied. During the transient phase, the current changes exponentially. If the circuit starts with current in the inductor, that current decays toward zero as time goes on. At this stage, the inductor acts like a short circuit, so the source...

design example: frog muscle response

RL Circuit and Frog Leg Current Response

An RL circuit is used to model the frog leg’s response to electrical stimulation. In this setup, the student studies how current changes in a resistor-inductor circuit can trigger muscle contraction. The circuit provides a way to control and measure the electrical impulses involved in the experiment. When the switch is closed, the frog’s leg shows a brief contraction. At steady state, the inductor acts like a short circuit. That lets current bypass the resistor and produces a mild, short...

second-order circuits

RLC Damping and Resonant Frequency

Second-order circuits use two energy storage elements, such as a capacitor and an inductor, to shape how current and voltage change over time. These circuits include RLC circuits, along with RC and RL circuits that have two capacitors or two inductors. Their behavior is described by second-order differential equations that connect the input signal to the output signal. The input usually comes from a voltage source or a current source. The output is often the voltage across the capacitor, the...

series rlc circuit without source

Natural Response of a Source-Free RLC Circuit

A source-free RLC circuit is a series circuit with a resistor, inductor, and capacitor, but no external energy source. It begins with the energy already stored in the capacitor and inductor. That stored energy drives the circuit at first. The circuit is described by a second-order differential equation. This equation shows how the resistor, inductor, and capacitor interact over time. The resistor removes energy from the circuit, so the solution has an exponential form. When the exponential...

types of responses of series rlc circuits

types-of-responses-of-series-rlc-circuits

Damping in Series RLC Circuit Responses

A source-free series RLC circuit shows three response patterns based on damping. The circuit is described by a second-order differential equation. Its complete solution is made from two distinct solutions. Those solutions depend on the roots, which are written in terms of the damping factor and the resonant frequency. When the damping factor is greater than the resonant frequency, both roots are real and negative. This gives an overdamped response. The circuit output decays slowly over time. <br...

series rlc circuit with source

Forced Response in a Series RLC Circuit

A series RLC circuit with a DC source can model an automobile ignition system. The circuit shows how a battery can produce the high voltage needed for a spark. In this case, the input DC voltage acts like a forcing step function. Applying Kirchhoff's voltage law leads to a second-order differential equation. A second-order differential equation is an equation with a term for the second derivative. The form of this equation is very similar to the one used for a source-free RLC circuit, so the...

parallel rlc circuits

Parallel RLC Step Response in Surge Protectors

Parallel RLC circuits help explain how a surge protector works in a street lamp. The circuit model uses a DC input source that creates a step response when the switch is turned on. This setup shows how the lamp’s components can be protected from sudden voltage spikes. When the switch closes, Kirchhoff’s current law is applied to the parallel RLC circuit. That leads to a second-order differential equation. The solution has two parts: a transient response and a steady-state response. The...

second-order op amp circuits

Second-Order Op Amp Low-Pass Filters

Second-order op-amp low-pass filters remove unwanted high-frequency noise from audio signals. They are used in audio systems to refine sound quality. These filters are often built as voltage followers and have two nodes with storage elements. The circuit analysis follows the same basic method used for second-order RLC circuits. In practice, bulky inductors are usually avoided because of their size and weight. For that reason, the focus here is on RC second-order op-amp circuits, which are...

design example: underdamped parallel rlc circuit

A parallel RLC circuit can be designed to work as an oscillator with underdamped behavior. This example targets a damped natural frequency of 4 kHz and a damping factor of 4 radians per second. A fixed resistance of 200 Ω is used as the starting point for the design. The first step is to find the capacitance. The damping factor is the reciprocal of twice the product of resistance and capacitance. Using that relationship, the needed capacitance value can be calculated from the given resistance...

key terms and concepts

Learn how a parallel RLC circuit is sized for oscillator use by finding capacitance and inductance from a target damped natural frequency and damping factor.

Oscillator Design with a Parallel RLC Circuit | JoVE K12

JoVE Core Electrical Engineering offers easy-to-understand animated videos that cover fundamental concepts of electric circuits along with circuit analysis techniques. It incorporates first-order and second-order circuits using operational amplifiers and circuit transformation concepts. The inclusion of practical design examples and real-world applications through scientist-in-action videos adds significant educational value, making complex concepts accessible.

electrical engineering

Oscillator Design with a Parallel RLC Circuit

Description

Transcript

Tags