Name: how buildings handle structural movement
Uploaded: 2024-09-12T16:16:29.000Z
Duration: 1 min 27 s
Channel: JoVE

Pueden producirse ligeros movimientos en los edificios durante la expansión de las unidades de construcción expuestas a la humedad o el levantamiento ascendente de los cimientos cuando el agua del suelo se expande mientras se congela.
Los movimientos pueden formar grietas en el edificio; para evitar esto, se proporcionan juntas de movimiento como juntas de trabajo, juntas de cerramiento de estructuras, juntas divisorias de superficie y juntas de separación de edificios.
Las juntas de trabajo se utilizan en techos de tejas, donde pequeñas tiras se ensamblan en un patrón superpuesto, tolerando ligeros movimientos sin ningún desgaste.
En una pared hueca, la junta blanda proporcionada debajo del ángulo del estante que soporta el borde exterior no estructural es un ejemplo de una junta de cerramiento de estructura.
Las juntas divisorias de superficie incluyen juntas de aislamiento, juntas de expansión y juntas de control.
Cuando se realizan nuevas adiciones a un edificio existente, se proporcionan juntas de aislamiento, lo que permite el movimiento de los nuevos materiales sin afectar el edificio existente.
Las juntas de expansión son ranuras abiertas diseñadas para permitir la expansión de los materiales de construcción, mientras que las juntas de control son líneas de debilidad creadas donde pueden ocurrir grietas cuando los materiales de construcción se encogen.
Por último, las juntas de separación de edificios subdividen las estructuras complejas de los edificios en segmentos discretos que pueden ser independientes de los movimientos de los demás.

juntas de movimiento en edificios

Las juntas de movimiento en los edificios son elementos de diseño esenciales que se adaptan a los movimientos inevitables causados ​​por diversos factores, como los cambios de temperatura, las variaciones del contenido de humedad y las deflexiones estructurales. Estos movimientos, si no se tienen en cuenta en el diseño y la construcción, pueden provocar daños antiestéticos o estructurales. Las juntas de movimiento se incorporan en diferentes formas para manejar estos esfuerzos y permitir que los materiales se muevan sin causar daños.

El tipo más simple de juntas de movimiento, las juntas de trabajo, se integran durante el proceso de construcción. Algunos ejemplos incluyen techos con tejas y revestimientos de madera biselados, que permiten los movimientos térmicos y de humedad. Las juntas estructurales/de cerramiento separan los elementos estructurales de los no estructurales para evitar la transferencia de carga que podría causar daños, como las vías de deflexión en las paredes con marcos de metal o las juntas blandas debajo de los ángulos de los estantes que sostienen los revestimientos de mampostería.

Las juntas de aislamiento se utilizan para evitar la interferencia entre materiales que necesitan moverse de forma independiente, esto es especialmente en las renovaciones o cuando las losas de concreto se encuentran con elementos estructurales. Las juntas de control crean líneas de debilidad predeterminadas para guiar el agrietamiento de manera controlada, y se observa comúnmente en aceras de concreto y paredes de yeso. Las juntas de expansión permiten la expansión y contracción del material, y son evidentes en muros de ladrillo y sistemas de muro cortina.

Por último, las juntas de separación en edificios dividen las estructuras complejas en segmentos que se mueven de manera independiente. Estas se clasifican en juntas de cambio de volumen, juntas de asentamiento y juntas de separación sísmica, cada una de las cuales aborda desafíos específicos relacionados con el movimiento estructural.

Juntas de movimiento en edificios

Pueden producirse ligeros movimientos en los edificios durante la expansión de las unidades de construcción expuestas a la humedad o el levantamiento ascendente de los cimientos cuando el agua en el ...

Education

Educación

JoVE Core

Civil Engineering

Ingeniería Civil

Unit 1

Unidad 1

Masonry

Albañilería

KEY TERMS AND CONCEPTS

TÉRMINOS Y CONCEPTOS CLAVE

Movement Joints in Buildings

how buildings handle structural movement

Buildings are designed to handle movement from temperature changes, moisture changes, and structural deflection. If these changes are ignored, they can cause visible damage or even unsafe conditions. Movement joints give building materials room to move without creating distress.

Working joints are the simplest type. They are placed during construction and help materials cope with change as the building goes up. Shingled roofs and wood bevel siding are common examples because they can move with thermal and moisture changes.

Some joints separate parts of the building so loads do not transfer where damage could happen. These are structure/enclosure joints. In metal-framed walls, deflection tracks help with this kind of movement. Soft joints under shelf angles that support masonry veneer also reduce stress between structural and nonstructural parts.

Isolation joints keep materials that need to move on their own from interfering with each other. They are often used in renovations or where a concrete slab meets a structural element. Control joints work differently. They create a planned line of weakness so cracking happens in a controlled way, such as in concrete sidewalks and plaster walls.

Expansion joints allow building materials to expand and contract. They are often seen in brick walls and curtain wall systems. Building separation joints divide a large structure into sections that can move independently. These include volume-change joints, settlement joints, and seismic separation joints, which each address a different kind of movement problem.

How Buildings Handle Structural Movement

composite masonry walls

Bonding and Materials in Composite Masonry

Composite masonry walls use two or more wythes, or vertical layers, of masonry to form one unified wall. The wythes may use the same material or different masonry materials. They are joined to work together as a single structure. These wythes can be bonded in several ways. Builders may use mortar-filled collar joints, grouted spaces, or rigid metal ties with reinforcement. Masonry header units can also connect the layers, but this method is rare. Metal ties are often preferred because they...

masonry cavity walls

Masonry Cavity Walls and Moisture Control

Masonry cavity walls use two wythes, or layers, with a hollow space between them. The outer and inner wythes are linked only by corrosion-resistant metal ties. This design helps manage water and improve wall performance. When rainwater passes through the outer wythe, it moves down through the cavity. Flashing catches the water and directs it toward weep holes, where it can leave the wall. The inner wythe often has damp-proofing on the cavity side. This layer also works as an air barrier. The...

masonry loadbearing walls

How Masonry Walls Support Buildings

Masonry load-bearing walls support floors and roofs and carry those loads down to the foundation. They are built from brick, stone, or concrete masonry units. These walls rely on compressive strength, which means they can resist pushes from above very well. Masonry walls may be reinforced or unreinforced, depending on the building needs. They carry dead loads and live loads while using working stresses that stay below the materials' ultimate strength. That safety margin helps the structure...

masonry curtain walls

Masonry Curtain Walls and Support Systems

Masonry curtain walls use brick or stone veneer as an exterior cladding system. The veneer is supported by the building structure, so the wall can be both attractive and functional. Two main construction methods are used for these walls. One method builds the masonry units in place through traditional layering. The other uses prefabricated panels that are assembled on the ground and then lifted into position. In traditional construction, steel shelf angles attached to the spandrel beam carry...

posttensioned masonry walls

How Masonry Walls Gain Extra Strength

Post-tensioned masonry walls gain extra strength from high-strength steel rods or flexible tendons. These tensioning elements are anchored to the foundation and run vertically through the wall. In some walls, they sit inside the cores of the masonry units. In others, they are placed between the masonry wythes, or layers. The wall is built first with the tensioning elements already in place. After the mortar cures fully, the wall is tightened. Steel rods are tensioned by turning nuts against...

cavity drainage and flashings in masonry walls

cavity-drainage-and-flashings-in-masonry-walls

Moisture Control in Masonry Cavity Walls

Masonry cavity walls use a gap between two wythes, or wall layers, to help control moisture. The cavity is usually at least 2 inches wide, and it may contain insulation. Even with insulation, a clear space of at least 1 inch is kept so water can drain away. Some walls also use a continuous drainage mat to reduce the needed space while still moving moisture out. Weep holes are another key part of cavity drainage. These openings sit at the base of the cavity and let collected water escape. They...

thermal insulation in masonry walls

Masonry Wall Insulation Options

Masonry wall insulation can be placed on the outside, inside the wall, or on the interior surface. The best choice depends on the climate, the building design, and whether the wall is being built new or retrofitted. In hot, dry climates, masonry can help smooth indoor temperatures by absorbing heat during the day and releasing it at night. In many other climates, extra insulation is needed to improve thermal resistance. One common exterior method is an Exterior Insulation and Finish System, or...

expansion and contraction in masonry walls

expansion-and-contraction-in-masonry-walls

Masonry Wall Joints for Temperature and Moisture

Masonry walls change size slightly as temperature and moisture change. Builders account for this movement so the wall does not crack or shift out of place. Thermal movement is usually easy to measure and plan for. Moisture movement is harder to predict. New clay masonry units often absorb water and expand over time in normal outdoor conditions. New concrete masonry units behave differently. They usually shrink as they lose extra moisture gained during production. These opposite changes make...

movement joints in buildings

Buildings are designed to handle movement from temperature changes, moisture changes, and structural deflection. If these changes are ignored, they can cause visible damage or even unsafe conditions. Movement joints give building materials room to move without creating distress. Working joints are the simplest type. They are placed during construction and help materials cope with change as the building goes up. Shingled roofs and wood bevel siding are common examples because they can move with...

types of building separation joints

Building Joints for Movement and Stability

Building separation joints help large or complex buildings move in a controlled way. They split a structure into smaller, separate units. This reduces stress when the building shifts under different forces. The joints are grouped into three main types: volume-change joints, settlement joints, and seismic separation joints. Volume-change joints handle expansion and contraction caused by temperature changes and moisture changes. They are placed where the building mass has discontinuities,...

efflorescence in masonry

Stopping White Salt Crystals on Masonry

Efflorescence is the white, fluffy crystal layer that can form on masonry walls. It happens when water-soluble salts in brick, stone, concrete, or mortar are dissolved by water and carried to the surface. When the water evaporates, the salts are left behind as a powdery deposit. New efflorescence is often seen soon after construction. In many cases, it can be cleaned with water and a brush. It may also fade over time as rain leaches salts out of the masonry surface. If efflorescence appears...

mortar joint deterioration in masonry

Repairing Damaged Mortar Joints in Masonry

Mortar joints in masonry can break down when water collects in them and freezes. The repeated freezing and thawing makes the water expand and shrink. That process creates cracks in the joints and can spread damage over time. As the mortar worsens, pieces may spall, or break off from the joint surface. Loose masonry units can follow, and the wall becomes weaker. Damaged joints also let moisture move into the wall, which adds to the problem. Good construction helps protect mortar joints. Using...

masonry in cold and hot weather conditions

masonry-in-cold-and-hot-weather-conditions

Protecting Mortar During Weather Changes

Masonry work changes in cold and hot weather because mortar must stay at the right temperature and moisture level. If mortar freezes before it cures, its strength and watertightness can drop. For proper hydration and curing, mortar should stay between 60°F and 80°F. When the weather is below 40°F, the water used for mortar must be heated. The water should not exceed 120°F, because very hot water can reduce compressive strength and bond strength. Masonry units and sand should also stay dry and...

masonry paving

Masonry Paving Materials and Base Layers

Masonry paving uses bricks, stones, and concrete masonry units to create durable walking and driving surfaces. These materials are selected for their shape, color, strength, and resistance to abrasion and weathering. Masonry units can be used in different paving setups depending on the site and the load they must carry. Some paving systems are installed dry on a thin sand layer over a gravel base. Others are set in mortar or asphalt on a concrete slab. For areas with heavy vehicular loads, a...

key terms and concepts

Learn how movement joints help buildings handle temperature, moisture, deflection, and cracking with examples from roofs, walls, masonry, and concrete.

How Buildings Handle Structural Movement | JoVE K12

JoVE Core Civil Engineering provides a foundational exploration of essential construction materials in civil engineering, focusing on bricks, stones, steel, wood, and concrete through easy-to-understand animated videos. This collection covers the properties, manufacturing processes, and practical applications of these materials. Additionally, the accompanied science-in-action videos demonstrate the research experiments performed in laboratories.

civil engineering

How Buildings Handle Structural Movement

Description

Transcript

Tags