Name: lumber cutting methods
Uploaded: 2024-09-12T16:16:32.000Z
Duration: 1 min 19 s
Channel: JoVE

Las piezas de madera largas y rectangulares que se utilizan en la construcción se denominan madera.
Los troncos cosechados de los árboles se descortezan y se alimentan repetidamente a través de una sierra automática.
Cada vez que se corta el tronco, las losas se transportan mediante una cinta transportadora a sierras más pequeñas. Aquí, las losas se cortan en madera de borde cuadrado de los anchos requeridos.
En esta etapa, las piezas cortadas tienen superficies rugosas y sus dimensiones pueden diferir ligeramente de un extremo a otro.
La madera aserrada se obtiene por aserrado liso o por cuartos. La madera lisa representa los anillos de crecimiento de los árboles planos en la cara más ancha del tablero y se usa típicamente como madera estructural.
En la madera aserrada en cuartos, los anillos de crecimiento se alinean aproximadamente a 45 grados o más en las maderas blandas y a 60 grados o más en las maderas duras con respecto a la cara más ancha de la tabla. La madera blanda aserrada en cuartos se utiliza para pisos, molduras y revestimientos.
El aserrado por grietas también se utiliza para maderas duras, con los anillos de crecimiento de la madera dura aserrada por grietas que se alinean en un ángulo de 30 a 60 grados con respecto a la cara ancha de la tabla y se utilizan cuando la apariencia y la durabilidad son esenciales.

madera

La madera se obtiene a partir de troncos que se talan, se descortezan y se procesan en trozos largos con una sección transversal rectangular. La transformación de los troncos en madera implica varios pasos, comenzando con una sierra automatizada que corta el tronco en tablas. Luego, estas tablas se transportan mediante una cinta transportadora a sierras más pequeñas, donde se cortan en piezas de bordes rectos de anchos específicos.
Inicialmente, las superficies de estas piezas de madera son rugosas y sus dimensiones pueden variar ligeramente de un extremo al otro. El método de corte de la madera influye significativamente en las características y aplicaciones de la madera. La madera se corta de tres maneras: aserrado tangencial, aserrado transversal o aserrado radial.

La madera aserrada por corte tangencial presenta anillos de crecimiento casi planos a lo largo de la cara más ancha de la tabla y se usa comúnmente en aplicaciones estructurales debido a su eficiencia en la producción y la rentabilidad. La madera aserrada por corte transversal, en la que los anillos de crecimiento se alinean aproximadamente 45 grados en las maderas blandas y 60 grados en las maderas duras con respecto a la cara más ancha de la tabla, se prefiere para productos como pisos, molduras y revestimientos debido a su mayor estabilidad y apariencia. El aserrado por corte radial, aplicado principalmente a las maderas duras, alinea los anillos de crecimiento en un ángulo de 30 a 60 grados, optimizando el atractivo estético y la durabilidad, lo que lo hace ideal para muebles de alta calidad y aplicaciones decorativas. Cada técnica de corte ofrece ventajas distintas, que atienden diferentes necesidades en las industrias de la construcción y la carpintería.

Madera

Las piezas de madera largas y rectangulares que se utilizan en la construcción se denominan madera.
Los troncos cosechados de los árboles se descortezan y se alimentan repetidamente a través de un sistema automatizado ...

Education

Educación

JoVE Core

Civil Engineering

Ingeniería Civil

Unit 1

Unidad 1

Wood

KEY TERMS AND CONCEPTS

TÉRMINOS Y CONCEPTOS CLAVE

Lumber

lumber cutting methods

Lumber is made from logs that are harvested, debarked, and processed into long pieces with a rectangular cross-section. The process starts when an automated saw slices a log into slabs. Those slabs then move on a conveyor belt to smaller saws, where they are cut into square-edged pieces of specific widths.

Freshly cut lumber usually has rough surfaces. Its dimensions may also vary slightly from one end to the other. The way wood is cut affects both the lumber’s appearance and how it is used.

Lumber is cut in three main ways: plainsawing, quartersawing, and riftsawing. Plainsawn lumber has growth rings that lie nearly flat on the board’s wider face. It is often used for structural applications because it is efficient to produce and cost-effective.

Quartersawn lumber places the growth rings at about 45 degrees in softwoods and 60 degrees in hardwoods to the wider face of the board. It is often chosen for flooring, trim, and siding because it is more stable and has a better appearance. Riftsawing is used mainly for hardwoods. It sets the growth rings at a 30 to 60-degree angle and is well suited for high-quality furnishings and decorative uses because it improves durability and visual appeal.

Lumber Cutting Methods

introduction to wood

Wood Structure and Uses in Building

Wood is a construction material made from trees. A tree trunk has several layers. The outside is a protective layer of dead bark. Under that is living bark, then the cambium, then sapwood. As sapwood matures, it becomes heartwood. The pith sits at the center of the trunk. The age of a tree can be read from its growth rings. These rings are concentric bands seen in a trunk cross-section. Wood strength also depends on grain. Grain refers to elongated, tubular cells that run along the length of...

softwoods and hardwoods

Wood Grain in Softwoods and Hardwoods

Softwoods and hardwoods come from different kinds of trees, and their leaf structures and cell makeup help explain how they are used. Softwoods come from cone-bearing trees with needle-like leaves. Hardwoods usually come from trees that shed broad leaves seasonally. Softwoods are made mostly of long cells called tracheids and a smaller number of rays, which are radial cells. This simpler structure gives softwoods a rougher grain. Because of this, they are often used in construction for...

lumber

Lumber is made from logs that are harvested, debarked, and processed into long pieces with a rectangular cross-section. The process starts when an automated saw slices a log into slabs. Those slabs then move on a conveyor belt to smaller saws, where they are cut into square-edged pieces of specific widths. Freshly cut lumber usually has rough surfaces. Its dimensions may also vary slightly from one end to the other. The way wood is cut affects both the lumber’s appearance and how it is used. <br...

structural properties and dimensions of lumber

structural-properties-and-dimensions-of-lumber

Wood Strength Tests and Lumber Sizes

Wood strength depends on how its fibers are aligned along the length of the tree. This alignment gives wood much greater tensile strength along the grain than across it, sometimes up to twenty times higher. Wood also tends to perform better under compression than under tension. Fiber length varies by wood type. Hardwoods have fibers about one twenty-fifth of an inch long. Softwoods have longer fibers that range from one-eighth to one-third of an inch. Laboratory tests help measure how wood...

seasoning of wood

Wood Drying for Stronger Construction

Seasoning of wood is the drying process used to lower and stabilize moisture content before wood is used in construction. Fresh wood can swell when it takes in moisture and contract as it dries. Seasoning helps reduce that movement so the wood stays more stable after it is built into a structure. The main goal is to reach equilibrium moisture content. This is the point where the wood’s moisture level matches the moisture in the surrounding environment. When wood is seasoned properly, it is...

wood surfacing

Wood Surfacing for Smooth, Safe Lumber

Wood surfacing smooths lumber, improves its size accuracy, and makes it safer to handle. It is a key finishing step in woodworking and construction. The process also helps correct small distortions that can form as wood dries. Before surfacing, the wood may be sized slightly larger to account for shrinkage during seasoning, which is the drying stage. A plane, a tool with rotating blades, is used to remove material and smooth the surface. The same tool can also round the edges a little, which...

lumber defects

Common Wood Flaws in Lumber

Lumber defects are flaws in wood that can change both its appearance and its strength. These defects come from tree growth and from the way lumber is processed. Knowing the main defects helps explain why some boards are better for construction and manufacturing than others. Some defects begin in the tree itself. Knots form where branches were once attached to the trunk, and knotholes appear when those knots fall out. Decay and insect damage are also natural defects that can weaken wood and...

wood fasteners

Wood Fastener Types and Uses

Wood fasteners connect parts of a wood structure and help keep members in place. The strength of the connection depends mainly on direct bearing between the wood members. Different fasteners are chosen for different jobs and structural needs. Nails are the most common wood fasteners. They are sharp-pointed metal pins that are driven into wood with a hammer or a mechanical nail gun. Nails come in many diameters, head styles, and lengths. Nailing methods also matter. Face nailing places the...

veneer

How Veneer Is Cut and Used

Veneer is a thin sheet of wood that is usually about one-eighth of an inch thick or less. It is made to show the look of wood while using timber more efficiently. Veneer is common in furniture and other finished wood products. One common way to make veneer is rotary cutting. In this method, a log is mounted in a large lathe and spun against a knife edge. As the knife moves deeper into the turning log, it peels off a continuous strip of wood. This creates rotary-cut veneer. Other veneer...

wood products

Engineered Wood Products in Construction

Engineered wood products are made from wood strands, veneers, lumber, and even waste wood shreds. They are used in both structural and nonstructural building applications. These materials are designed to improve strength, durability, and versatility in modern construction. Glue-laminated wood, or glulam, is made by bonding several smaller pieces of dimensional lumber with adhesive. Cross-laminated timber uses solid lumber panels with layers placed so the grain direction alternates. This layer...

wood panel products

Types of Wood Panels in Construction

Wood panels are common construction materials used for flooring, siding, and roofing. They usually come in standard 4-foot by 8-foot sheets. Their thickness can range from one-quarter of an inch to one and one-eighth inches. Plywood is one of the most familiar wood panels. It is made by gluing thin wood veneers, or layers, under pressure. The outer veneer grain runs lengthwise, while the inner layers run widthwise. Plywood also has an odd number of layers, which helps keep the panel...

key terms and concepts

Learn how logs become lumber and how plainsawing, quartersawing, and riftsawing change the wood’s look, stability, and uses in construction and furniture.

Lumber Cutting Methods | JoVE K12

JoVE Core Civil Engineering provides a foundational exploration of essential construction materials in civil engineering, focusing on bricks, stones, steel, wood, and concrete through easy-to-understand animated videos. This collection covers the properties, manufacturing processes, and practical applications of these materials. Additionally, the accompanied science-in-action videos demonstrate the research experiments performed in laboratories.

civil engineering

Lumber Cutting Methods

Description

Transcript

Tags