Name: gas equilibrium under volume changes
Uploaded: 2020-09-24T15:06:51.000Z
Duration: 2 min 32 s
Channel: JoVE

K12 Standards

north-carolina-k-12-science-standard-course-of-study

North Carolina K-12 Science Standard Course of Study

9-12

Chemistry

Matter and its Interactions

PS.Chm.5.2

le-chatelier-s-principle-changing-volume-pressure

Le Chatelier's Principle: Changing Volume (Pressure)

Le principe Le Châtelier peut être utilisé pour prévoir comment un système à l'équilibre répondrait au stress d'un changement en volume ou en pression. Le volume d'un gaz est inversement proportionnel à sa pression;donc, pour un système à l'équilibre, une diminution de volume augmente la pression et perturbe l'équilibre. En réponse, la position d'équilibre se déplacera dans une direction pour minimiser le stress.La loi des gaz parfaits stipule que la pression d'un gaz est directement proportionnel au nombre de moles. Ainsi, la direction du déplacement nécessaire pour rétablir l'équilibre dépend du nombre de moles de particules de gaz de part et d'autre de la réaction. Comme plus de moles de gaz entraîne une pression plus élevée, une augmentation de la pression déplace la position d'équilibre du côté où il y a moins de moles pour faire baisser la pression.De même, une diminution de la pression déplace la position d'équilibre sur le côté avec plus de moles de gaz. Considérons un équilibre chimique, où une mole de pentachlorure de phosphore se décompose en une mole de trichlorure de phosphore et une mole de chlore gazeux deux moles totales de produit. Si le piston est abaissé, le volume du système d'équilibre diminue, ce qui augmente la pression.Cela perturbe l'équilibre et entraîne un Q supérieur à K.Ainsi, la position d'équilibre se déplace vers les réactifs, avec moins de moles de particules de gaz, afin de diminuer la pression et rétablir l'équilibre. Inversement, tirer le piston vers le haut augmente le volume et diminue la pression. Dans ce cas, Q devient plus petit que K.Afin d'élever la pression, la position d'équilibre se déplace vers les produits, le côté avec le plus de moles de gaz, le plus de moles de gaz, et rétablit l'équilibre.Augmenter la pression en ajoutant un gaz inerte à un mélange d'équilibre à volume constant, n'affecte pas l'équilibre car les pressions partielles des réactifs et produits gazeux restent inchangés. Pour les systèmes d'équilibre à nombres égaux de moles de réactifs et de produits gazeux, comme la réaction entre l'iode gazeux et le chlore gazeux pour produire du monochlorure d'iode, un changement dans le volume du système aura aucun effet sur l'équilibre.

principe de le châtelier : modification du volume (pression)

Pour les équilibres en phase gazeuse, des changements de la concentration des réactifs et des produits peuvent se produire lorsque le volume et la pression sont modifiés. La pression partielle, P, d'un gaz parfait est proportionnelle à sa concentration molaire, M. 
 <img alt="Eq1" src="/files/ftp_upload/11392/11392_Equation 1.png" style="text-align: center; height: 70px;" />
 Ainsi, les modifications des pressions partielles d'un réactif ou d'un produit sont essentiellement des changements de concentrations ; par conséquent, ces modifications produisent les mêmes effets sur les équilibres. Outre l'ajout ou l'élimination de réactifs ou de produits, les pressions (concentrations) des espèces dans un équilibre en phase gazeuse peuvent également être modifiées en modifiant le volume occupé par le système. Étant donné que toutes les espèces d'un équilibre en phase gazeuse occupent le même volume, une modification donnée du volume entraînera le même changement de concentration pour les réactifs et les produits. Afin de discerner quel déplacement, le cas échéant, ce type de contrainte induit, la stœchiométrie de la réaction doit être considérée. 
 À l'équilibre, la réaction N2 (g) + O2 (g) ⇌ 2 NO (g) est décrite par le quotient de la réaction 
 <img alt="Eq2" src="/files/ftp_upload/11392/11392_Equation 2.png" style="text-align: center; height: 70px;" />
 Si on diminue par un facteur de 3 le volume occupé par un mélange en équilibre de ces espèces, les pressions partielles des trois espèces seront augmentées par un facteur de 3 : 
 <img alt="Eq3" src="/files/ftp_upload/11392/11392_Equation 3.png" style="text-align: center; height: 70px;" />
 Ainsi, la modification du volume de ce mélange en équilibre en phase gazeuse n'entraîne pas un déplacement de l'équilibre. 
 En traitant de façon similaire un système différent, 2 SO2 (g) + O2 (g) ⇌ 2 SO3 (g), cela donne toutefois un résultat différent : 
 <img alt="Eq4" src="/files/ftp_upload/11392/11392_Equation 4.png" style="text-align: center; height: 200px;" />
 Dans ce cas, le résultat de la modification du volume est un quotient réactionnel plus petit que la constante d'équilibre, et donc l'équilibre se déplace vers la droite. 
 Ces résultats illustrent la relation entre la stœchiométrie d'un équilibre en phase gazeuse et l'effet d'un changement de pression (concentration) induit par le volume. Si les quantités molaires totales de réactifs et de produits sont égales, comme dans le premier exemple, une modification du volume ne déplace pas l'équilibre. Si les quantités molaires de réactifs et de produits sont différentes, une modification du volume déplace l'équilibre dans un sens qui “ adapte ” mieux le changement de volume. Dans le second exemple, trois moles de réactif (SO2 et O2) donnent deux moles de produit (SO3), et donc la diminution du volume du système provoque un déplacement de l'équilibre vers la droite puisque la réaction directe produit moins de gaz (2 mol) que la réaction inverse (3 mol). Inversement, l'augmentation du volume de ce système en équilibre entraînerait un déplacement vers les réactifs. 
 Ce texte a été adapté d’<a href="https://openstax.org/books/chemistry-2e/pages/13-3-shifting-equilibria-le-chateliers-principle">Openstax, Chimie 2e, Section 13.3 Déplacements d'équilibres : le principe de Le Chatelier</a>.

Principe de Le Châtelier : modification du volume (pression)

Pour les équilibres en phase gazeuse, des changements dans les concentrations de réactifs et de produits peuvent se produire avec une modification du volume et de la pression. La pression partielle, P, de ...

Education

Enseignement

JoVE Core

Chimie

Chemical Equilibrium

Équilibre chimique

KEY TERMS AND CONCEPTS

TERMES ET CONCEPTS CLÉS

gas equilibrium under volume changes

Gas-phase equilibrium can shift when the volume of the system changes. In these reactions, a change in pressure changes concentration because the partial pressure of an ideal gas is proportional to its molar concentration. That means pressure changes affect equilibrium in the same way as concentration changes.

When the volume of a gas mixture changes, the concentrations of reactants and products change together. Since every gas in the equilibrium occupies the same space, the same volume change affects each species in the same way. To predict whether the equilibrium shifts, you must look at the reaction stoichiometry.

For the equilibrium N2(g) + O2(g) ⇌ 2 NO(g), decreasing the volume by a factor of 3 increases the partial pressures of all three gases by a factor of 3. In this case, the reaction quotient still matches the equilibrium position, so the equilibrium does not shift. The total moles of reactants and products are equal, and that is why the volume change has no effect.

A different result appears for 2 SO2(g) + O2(g) ⇌ 2 SO3(g). Here, decreasing the volume makes the reaction quotient smaller than the equilibrium constant, so the equilibrium shifts right. Three moles of reactant form two moles of product, so the forward reaction makes less gas. Increasing the volume would shift this system toward the reactants.

Gas Equilibrium Under Volume Changes

the equilibrium constant

Chemical Equilibrium and Kc Rules

Chemical equilibrium and the equilibrium constant Kc describe how reactants and products are balanced in a reaction. In the oxidation of sulfur dioxide, a mixture that starts with reactants only has no product at first. As the reaction moves forward toward equilibrium, reactant concentrations decrease and product concentration increases. When equilibrium is reached, the concentrations of both stay constant. A reaction can also begin with only products present. In that case, the reaction moves...

homogeneous equilibria for gaseous reactions

homogeneous-equilibria-for-gaseous-reactions

Relating Kc and Kp in Gas Equilibria

Gas-phase equilibrium can be written using either concentration or pressure. The equilibrium constant may be shown as Kc, which uses molar concentration, or as Kp, which uses partial pressure of the reactants and products. The link between Kc and Kp comes from the ideal gas equation and the definition of molarity. Molarity is the number of moles divided by volume. In the ideal gas equation, P stands for partial pressure, V for volume, n for number of moles, R for the gas constant, and T for...

le chatelier's principle: changing concentration

le-chatelier-s-principle-changing-concentration

Shifting Equilibrium by Changing Concentration

Chemical equilibrium is a dynamic balance. At equilibrium, the forward and reverse reactions happen at equal rates. If the system is stressed in a way that changes one rate more than the other, it is no longer at equilibrium and will shift until balance is restored. This behavior is described by Le Châtelier’s principle. Changes in concentration are a major stress on an equilibrium system. Reaction rates depend mainly on concentration and temperature. For that reason, changing the amount of a...

calculating the equilibrium constant

Finding Kc from Equilibrium Data

The equilibrium constant, Kc, can be found from the equilibrium concentrations of reactants and products. When those concentrations are known, the calculation is straightforward. The values are placed into the Kc expression for the reaction. One example uses nitrogen dioxide and dinitrogen tetroxide. When 0.10 mol NO2 is added to a 1.0-L flask at 25 °C, the concentrations change until equilibrium is reached. At equilibrium, [NO2] is 0.016 M and [N2O4] is 0.042 M, and these values are used to...

reaction quotient

Using Q to Track Equilibrium Changes

Reaction quotient Q helps track how far a reversible reaction has moved toward equilibrium. For a balanced reaction such as m A + n B ⇌ x C + y D, Q comes directly from the stoichiometric coefficients in the equation. When concentrations are used, the expression is written as Qc. For gases, a similar form uses partial pressures. These expressions use relative concentration and pressure values, not absolute values. That means reaction quotients are dimensionless and have no units. As a reaction...

dynamic equilibrium

Chemical Equilibrium in Reversible Reactions

Chemical equilibrium in reversible reactions happens when a reaction moves in both directions at the same time. A reversible reaction uses a double arrow to show that products can turn back into reactants. At equilibrium, the concentrations of reactants and products stay constant over time because the forward and reverse reaction rates are equal. The video uses the reversible decomposition of colorless dinitrogen tetroxide to brown nitrogen dioxide as an example. At time zero, there is finite...

calculating equilibrium concentrations

Equilibrium Concentrations from an ICE Table

Equilibrium concentrations can be found from initial concentrations and an equilibrium constant. This skill matters in many areas of science and technology, including pharmaceutical product formulation and dosing. After a drug is ingested or injected, it may take part in several chemical equilibria that change its final concentration in the body system of interest. Scientists use these quantitative equilibrium relationships to help calculate a dosage that will produce the desired therapeutic...

le chatelier's principle: changing volume (pressure)

Gas-phase equilibrium can shift when the volume of the system changes. In these reactions, a change in pressure changes concentration because the partial pressure of an ideal gas is proportional to its molar concentration. That means pressure changes affect equilibrium in the same way as concentration changes. When the volume of a gas mixture changes, the concentrations of reactants and products change together. Since every gas in the equilibrium occupies the same space, the same volume change...

le chatelier's principle: changing temperature

le-chatelier-s-principle-changing-temperature

Le Chatelier's Principle in Heating and Cooling

Le Chatelier's principle helps explain how chemical equilibrium responds to heating and cooling. A system at equilibrium will shift to restore balance after a temperature change, but the equilibrium constant, K, will not stay the same. Instead, the mixture reaches a new equilibrium with a different composition. This temperature effect is different from a concentration change, which shifts equilibrium without changing K. To understand why temperature matters, the reaction can be written with...

the small x assumption

Estimating Equilibrium with Small Changes

A small equilibrium constant can make equilibrium calculations easier. In these reactions, the equilibrium position favors the reactants. When the initial reactant concentration is high and the Kc value is small, the change in concentration may be negligible. In that case, the equilibrium concentration is close to the initial concentration. This idea helps simplify weak acid and weak base problems. Chemists can assume that some equilibrium concentrations are equal to the initial concentrations.

key terms and concepts

Learn how changing volume changes pressure and concentration in gas-phase equilibrium, and why stoichiometry decides whether the system shifts left or right.

Gas Equilibrium Under Volume Changes | JoVE K12

chemistry

JoVE Core Chimie anime les concepts de chimie générale en utilisant des leçons vidéo concises et faciles à comprendre. De plus, nos vidéos de scientifiques à l'action présentent des expériences de recherche, classiques ou insolites, effectuées dans des laboratoires modernes du monde entier.

ohios-learning-standards-and-model-curriculum

Ohio’s Learning Standards and Model Curriculum

Interactions Of Matter

Chemical reactions

Minnesota Academic Standards in Science

2.2.1 9C.1.2.1.1

Arizona Science Standards

High School

Physical Science

HS+C.P1

HS+C.P1U1.6

new-jersey-student-learning-standards-for-science

New Jersey Student Learning Standards for Science

Matter and Its Interactions

HS-PS1-6

Next Generation Science Standards

Florida Department of Education

SC.912.P.12

SC.912.P.12.13

new-york-state-science-learning-standards

New York State Science Learning Standards

HS. Chemical Reactions

HS-PS1-6.

Georgia Standards of Excellence

SC4.

concentration-temperature-and-pressure-effects

Concentration, Temperature, and Pressure Effects

Scientific Laws and Theories

Scientific Laws

In science, a law is defined as a concise, verbal or mathematical, statement that summarizes a vast number of experimental observations. ...

The Scientific Method

Chemistry is an empirical science. Scientists often pose questions to understand the chemistry in everyday life and seek answers to these questions. To ...

Classifying Matter by State

Chemistry is the study of matter and the changes it undergoes. Matter is anything that has mass and occupies space. Matter is all around us; the air, ...

Classifying Matter by Composition

Matter: Pure Substances and Mixtures
According to its composition, the matter can be classified into two broad categories &mdash; pure substances and ...

The Atomic Theory of Matter

The earliest recorded discussion of the basic structure of matter comes from ancient Greek philosophers. Leucippus and Democritus argued that all matter ...

Subatomic Particles

Dalton was only partially correct about the particles that make up matter. All matter is composed of atoms, and atoms are composed of three smaller ...

Elements: Chemical Symbols and Isotopes

A chemical symbol is an abbreviation used to indicate an element or an atom of an element. For example, the symbol for mercury is Hg. The same symbol is ...

Use models to explain how the scientific understanding of atomic structure has evolved.

PS.Chm.1.1

Radioactivity and Nuclear Equations

Nuclear chemistry is the study of reactions that involve changes in nuclear structure. The nucleus of an atom is composed of protons and, except for ...

Types of Radioactivity

The most common types of radioactivity are &#945; decay, &#946; decay, &#947; decay, neutron emission, and electron capture.
Alpha (&#945;) decay is the ...

Nuclear Stability

Protons and neutrons, collectively called nucleons, are packed together tightly in a nucleus. With a radius of about 10&#8722;15 meters, a nucleus is ...

Nuclear Binding Energy

The difference between the calculated and experimentally measured masses is known as the mass defect of the atom. In the case of helium-4, the mass defect ...

Radioactive Decay and Radiometric Dating

Radioactivity is a spontaneous disintegration of an unstable nuclide and is a random process, as all the nuclei in the sample do not decay simultaneously. ...

Nuclear Fission

Many heavier elements with smaller binding energies per nucleon can decompose into more stable elements that have intermediate mass numbers and larger ...

Nuclear Power

Controlled nuclear fission reactions are used to generate electricity. Any nuclear reactor that produces power via the fission of uranium or plutonium by ...

Nuclear Fusion

The process of converting very light nuclei into heavier nuclei is also accompanied by the conversion of mass into large amounts of energy, a process ...

Nuclear Transmutation

Nuclear transmutation is the conversion of one nuclide into another. It can occur by the radioactive decay of a nucleus, or the reaction of a nucleus with ...

Use models to compare nuclear reactions including alpha decay, beta decay and gamma decay; nuclear fusion and nuclear fission.

PS.Chm.1.2

Atomic Orbitals

An atomic orbital represents the three-dimensional regions in an atom where an electron has the highest probability to reside. The radial distribution ...

The Pauli Exclusion Principle

The arrangement of electrons in the orbitals of an atom is called its electron configuration. We describe an electron configuration with a symbol that ...

The Energies of Atomic Orbitals

In an atom, the negatively charged electrons are attracted to the positively charged nucleus. In a multielectron atom, electron-electron repulsions are ...

The Aufbau Principle and Hund's Rule

To determine the electron configuration for any particular atom, we can build the structures in the order of atomic numbers. Beginning with hydrogen, and ...

electron-configuration-of-multielectron-atoms

Electron Configuration of Multielectron Atoms

The alkali metal sodium (atomic number 11) has one more electron than the neon atom. This electron must go into the lowest-energy subshell available, the ...

Use models to explain how electrons are distributed in atoms.

PS.Chm.1.3

Periodic Classification of the Elements

The periodic table arranges atoms based on increasing atomic number so that elements with the same chemical properties recur periodically. When their ...

The Periodic Table

As early chemists discovered more elements, they realized that various elements could be grouped by their similar chemical behaviors. One such grouping ...

Atomic Mass

Atoms &mdash; and the protons, neutrons, and electrons that compose them &mdash; are extremely small. For example, a carbon atom weighs less than 2 ...

Molar Mass

The identity of a substance is defined not only by the types of atoms or ions it contains but by the quantity of each type of atom or ion. For example, ...

Use the Periodic Table as a model to predict the relative properties of elements based on the pattern of valence electrons in the outermost energy levels of atoms.

PS.Chm.2.1

atomic-radii-and-effective-nuclear-charge

Atomic Radii and Effective Nuclear Charge

The elements in groups of the periodic table exhibit similar chemical behavior. This similarity occurs because the members of a group have the same number ...

Ionic Radii

Ionic radius is the measure used to describe the size of an ion. A cation always has fewer electrons and the same number of protons as the parent atom; it ...

Ionization Energy

The amount of energy required to remove the most loosely bound electron from a gaseous atom in its ground state is called its first ionization energy ...

Electron Affinity

The electron affinity (EA) is the energy change for adding an electron to a gaseous atom to form an anion (negative ion).



This process can be either ...

Construct an explanation to infer the atomic size, reactivity, electronegativity, and ionization energy of an element based on its position in the Periodic Table.

PS.Chm.2.2

Types of Chemical Bonds

Chemical bonding theories were pioneered by American chemist Gilbert&#xA0;N. Lewis. He developed a model called the Lewis model to explain the type and ...

Lewis Symbols and the Octet Rule

Chemical bonds are complex interactions between two or more atoms or ions, which reduce the potential energy of the molecule. Gilbert N. Lewis developed a ...

Ionic Bonding and Electron Transfer

Ions are atoms or molecules bearing an electrical charge. A cation (a positive ion) forms when a neutral atom loses one or more electrons from its valence ...

The Born-Haber Cycle

Lattice Energy&#xA0;

An ionic compound is stable because of the electrostatic attraction between its positive and negative ions. The lattice energy of a ...

trends-in-lattice-energy-ion-size-and-charge

Trends in Lattice Energy: Ion Size and Charge

An ionic compound is stable because of the electrostatic attraction between its positive and negative ions. The lattice energy of a compound is a measure ...

Covalent Bonding and Lewis Structures

Compared to ionic bonds, which results from the transfer of electrons between metallic and nonmetallic atoms, covalent bonds result from the mutual ...

Electronegativity

Whether a bond is nonpolar or polar covalent is determined by a property of the bonding atoms called electronegativity.&#xA0;

Electronegativity values of ...

bond-polarity-dipole-moment-and-percent-ionic-character

Bond Polarity, Dipole Moment, and Percent Ionic Character

Bond Polarity

The absolute value of the difference in electronegativity (&Delta;EN) of two bonded atoms provides a rough measure of the polarity to be ...

lewis-structures-of-molecular-compounds-and-polyatomic-ions

Lewis Structures of Molecular Compounds and Polyatomic Ions

To draw Lewis structures for complicated molecules and molecular ions, it is helpful to follow a step-by-step procedure as outlined:


	Determine the ...

Resonance

The Lewis structure of a nitrite anion (NO2&minus;) may actually be drawn in two different ways, distinguished by the locations of the N-O and N=O ...

Formal Charges

In some cases, there are seemingly more than one valid Lewis structures for molecules and polyatomic ions. The concept of formal charges can be used to ...

Exceptions to the Octet Rule

Many covalent molecules have central atoms that do not have eight electrons in their Lewis structures. These molecules fall into three categories:


	...

Bond Energies and Bond Lengths

Stable molecules exist because covalent bonds hold the atoms together. The strength of a covalent bond is measured by the energy required to break it, ...

Analyze and interpret data to explain the mechanisms and properties of the two main types of intramolecular (ionic and covalent) bonds.

PS.Chm.3.1

molecular-comparison-of-gases-liquids-and-solids

Molecular Comparison of Gases, Liquids, and Solids

Particles in a solid are tightly packed together (fixed shape) and often arranged in a regular pattern; in a liquid, they are close together with no ...

Intermolecular vs Intramolecular Forces

Intermolecular forces (IMF) are electrostatic attractions arising from charge-charge interactions between molecules. The strength of the intermolecular ...

Intermolecular Forces

Atoms and molecules interact through bonds (or forces): intramolecular and intermolecular. The forces are electrostatic as they arise from interactions ...

comparing-intermolecular-forces-melting-point-boiling-point

Comparing Intermolecular Forces: Melting Point, Boiling Point, and Miscibility

Intermolecular forces are attractive forces that exist between molecules. They dictate several bulk properties, such as melting points, boiling points, ...

Construct an explanation to summarize the influences intermolecular forces have on the properties of chemical compounds.

PS.Chm.3.2

Analyze the structure of atoms and isotopes.

Gas Equilibrium Under Volume Changes

Description

Transcript

Tags

More videos by Standards