Name: reducing power loss in three-phase lines
Uploaded: 2024-07-08T13:19:58.000Z
Duration: 1 min 10 s
Channel: JoVE

Considérons un circuit Y-Y à trois fils symétrique représenté dans le domaine temporel, qui peut être transformé en un circuit équivalent par phase.
Tout d’abord, le courant de ligne est déterminé, suivi de la tension de phase à la charge.
Ensuite, la puissance délivrée par la source est déterminée à l’aide des valeurs effectives de la tension de phase sinusoïdale et du courant de ligne.
Ensuite, la puissance délivrée à la charge est calculée à l’aide du courant de ligne et de la résistance de la charge.
La puissance perdue dans la ligne est obtenue à l’aide du courant de ligne et de la résistance de ligne.
Ensuite, la puissance totale fournie par la source triphasée, la puissance totale reçue par la charge triphasée et la puissance totale perdue dans les lignes sont déterminées.
Un pourcentage élevé de puissance est perdu dans la ligne, ce qui peut être réduit en minimisant le courant de ligne.
Cependant, cela réduirait le courant de charge, ce qui diminuerait à son tour la puissance fournie à la charge.
Une façon de réduire le courant de ligne sans affecter le courant de charge est d’introduire des transformateurs dans le circuit triphasé.

perte de ligne

Les différentes configurations de connexions source-charge incluent les connexions en étoile (étoile) et en triangle. La relation entre les tensions et courants de ligne et de phase varie en fonction de la configuration. Lorsque la source fournit de l'énergie, celle-ci est transmise à la charge via les fils et, pendant cette transmission, une partie de l'énergie est absorbée par les fils, entraînant une perte de ligne.
La perte de ligne a un impact sur l’efficacité de la fourniture d’énergie dans un circuit triphasé équilibré. La symétrie d’un tel circuit simplifie l’analyse en permettant de ne considérer qu’une seule phase. Le circuit équivalent par phase facilite le calcul de divers paramètres, y compris la perte de ligne

Calcul de la perte de puissance :
La puissance délivrée à chaque phase de la charge est le produit du carré du courant de phase et de la résistance de charge de phase.
Calcul de perte de ligne :
La perte de ligne pour chaque fil est calculée en prenant le carré de l'amplitude du courant de ligne et en le multipliant par la résistance de la ligne.
Pour les systèmes triphasés équilibrés, ce calcul est multiplié par trois (un pour chaque phase) pour obtenir la perte de puissance totale. La résistance de la ligne est directement proportionnelle à la résistivité du matériau et à la longueur de la ligne, et inversement proportionnelle à la section transversale du conducteur. Cela signifie que la perte de ligne est directement proportionnelle à la longueur du conducteur et inversement proportionnelle à la section transversale du conducteur. Les compagnies d'électricité utilisent des conducteurs avec des sections transversales plus grandes pour minimiser les pertes de ligne et transmettre la puissance à des tensions plus élevées, ce qui permet un courant plus faible pour la même quantité de puissance. Cela est dû au fait que la puissance est le produit de la tension et du courant, et pour un niveau de puissance donné, l'augmentation de la tension permet une diminution du courant, réduisant ainsi les pertes en ligne.

Perte de ligne

Considérons un circuit Y-Y à trois fils symétrique représenté dans le domaine temporel, qui peut être transformé en un circuit équivalent par phase.
Tout d’abord, le ...

Education

Enseignement

JoVE Core

Electrical Engineering

Génie électrique

Unit 1

Unité 1

Three-Phase Circuits

Circuits triphasés

KEY TERMS AND CONCEPTS

TERMES ET CONCEPTS CLÉS

Line Loss

reducing power loss in three-phase lines

Three-phase power lines can lose energy as electricity travels from the source to the load. This line loss affects how efficiently power reaches the load. In balanced three-phase circuits, the symmetry makes the analysis easier because one phase can represent the whole system.

The source-load connection can use wye, also called star, or delta configurations. These setups change the relationship between line voltage, phase voltage, line current, and phase current. A per-phase equivalent circuit helps calculate the power delivered to the load and the power lost in the lines.

For each phase of the load, the delivered power depends on the square of the phase current and the phase load resistance. The power lost in one wire is found from the square of the line current multiplied by the resistance of that line. For a balanced three-phase system, the total line loss is three times the loss in one phase.

Line resistance depends on the material resistivity, the length of the conductor, and its cross-sectional area. As the line gets longer, resistance and line loss increase. A larger cross-sectional area lowers resistance and helps reduce loss. Power companies use larger conductors and higher transmission voltages to keep current lower for the same power level, which reduces line loss.

Reducing Power Loss in Three-Phase Lines

three-phase circuits

How Three-Phase Power Delivers Electricity

Three-phase power is a major part of AC power distribution, especially where steady and efficient electricity delivery is needed. AC systems are grouped into single-phase, two-phase, and three-phase systems. These categories help describe how power moves from the source to the load. Single-phase circuits are common in homes. They usually use a two-wire system that connects one AC source to loads. These circuits can supply everyday appliances such as lamps, televisions, and microwaves at 120 V...

generation of three-phase voltage

Three-Phase AC Generator Windings

A three-phase AC generator uses rotating magnet windings and a stationary stator to make three-phase voltage. The rotor carries a magnet that spins inside the stator. The stator holds the three-phase winding, and mutual induction creates the voltage. The stator windings are spread evenly around the inside of the stator. They are placed 120 electrical degrees apart. These windings consist of three separate coils, or groups of coils, called phases. The phases can be connected in a Y, or star,...

three-phase voltages

Three-Phase Power Connections

Three-phase power connections use balanced voltages that are equal in magnitude and separated by 120 degrees. A three-phase generator produces these voltages, and the balance helps reduce power loss while keeping energy delivery steady to connected loads. Three-phase sources can be arranged in either wye or delta form. The loads connected to the system can also use wye or delta. This flexibility gives control over how the system is designed and managed. In a wye connection, one end of each...

the y-to-y circuit

Balanced Wye-to-Wye Neutral Current

A balanced wye-to-wye circuit uses three wye-connected sinusoidal voltage sources and three wye-connected loads. A neutral wire links the neutral node of the source to the neutral node of the load. The load impedance is connected across each phase of the load. The source and load can be connected in either a four-wire or a three-wire arrangement. A three-phase system is balanced when each phase has the same load. In that case, the current flow and phase angle are uniform across the system. If...

the y-to-delta circuit

Wye Source and Delta Load Currents

A balanced wye source and delta load form a common three-phase circuit with no neutral line connection. The source is Y-connected, and the load is delta-connected. To analyze the circuit, the first step is to assume a positive phase sequence. These phase voltages are then used to find the line voltages that appear across the delta load impedances. In the wye source, the phase voltages are V an, V bn, and V cn. In the delta load, the line voltages are V ab, V bc, and V ca. These line voltages...

the delta-to-delta circuit

Balanced Delta-Delta Power Circuit

A balanced delta-delta power circuit uses a delta-connected source and a delta-connected load. The two deltas form a closed loop that creates three separate phases. In this setup, the phase voltages are the same as the line voltages. If the source is in positive sequence, the phase voltages can be written directly, and no neutral wire is needed. The delta-connected load current is found by dividing the phase voltage by the impedance of each phase. For line current, Kirchhoff’s Current Law...

the delta-to-y circuit

Delta-Wye Source and Load Connections

A balanced delta-wye circuit connects a delta-connected source to a wye-connected load. In this setup, the phase voltage of the delta source equals the line voltage of the wye load. The source also sets the line currents that flow into the load. For a balanced system, the phase difference between currents makes it possible to find one line current from the other by using the positive sequence of phases. In the wye-connected load, each phase current equals the line current from the delta source.

power in a three-phase circuit

Balanced Three-Phase Power Calculation

Balanced three-phase power calculation depends on the wye and delta connections used in the circuit. A wye, or star, configuration can use three wires or four wires. A delta configuration connects the components in a closed loop. These connection types change how voltages and currents are arranged, but both are used in three-phase systems. In a balanced three-phase system, instantaneous power is the power at one exact moment. Even though the power in each phase changes over time, the total...

power distribution in three-phase and single phase circuits

power-distribution-in-three-phase-and-single-phase-circuits

Single-Phase vs. Three-Phase Power Loss

Single-phase and three-phase circuits distribute electrical power in different ways. Single-phase power is common in homes, while balanced three-phase power is widely used in industrial settings with heavy machinery. Both systems deliver energy, but their current flow and wire needs are not the same. A single-phase circuit usually uses a two-wire system. The current depends on the power absorbed by the load and the line voltage. Because wire loss from resistance follows the square of the...

line loss

Three-phase power lines can lose energy as electricity travels from the source to the load. This line loss affects how efficiently power reaches the load. In balanced three-phase circuits, the symmetry makes the analysis easier because one phase can represent the whole system. The source-load connection can use wye, also called star, or delta configurations. These setups change the relationship between line voltage, phase voltage, line current, and phase current. A per-phase equivalent circuit...

reducing line loss

Cutting Heat Loss in Three-Phase Lines

Three-phase power systems can lose energy as heat in transmission lines because the wires have resistance. This line loss becomes important when electricity travels over a distance. A common solution is to use transformers to change the voltage and current in the system. The setup uses two three-phase transformers. A step-up transformer is placed at the source, and a step-down transformer is placed at the load. Raising the voltage at the source lowers the current in the transmission lines, and...

key terms and concepts

Learn how balanced three-phase circuits, wye and delta connections, and conductor size affect line loss, power delivery, and transmission efficiency.

Reducing Power Loss in Three-Phase Lines | JoVE K12

JoVE Core Electrical Engineering offers easy-to-understand animated videos that cover fundamental concepts of electric circuits along with circuit analysis techniques. It incorporates first-order and second-order circuits using operational amplifiers and circuit transformation concepts. The inclusion of practical design examples and real-world applications through scientist-in-action videos adds significant educational value, making complex concepts accessible.

electrical engineering

Reducing Power Loss in Three-Phase Lines

Description

Transcript

Tags