Name: common wood flaws in lumber
Uploaded: 2024-09-12T16:16:32.000Z
Duration: 1 min 23 s
Channel: JoVE

Les défauts de croissance du bois comprennent des nœuds, qui se forment là où les branches se connectent au tronc de l’arbre, des trous de nœuds résultant de la chute de nœuds lâches, de la pourriture et des dommages causés par les insectes.
Les bardeaux de fente sont des fractures mineures le long ou à travers les anneaux annuels et sont des défauts courants du bois.
Le wane fait référence au manque de bois ou à la présence d'écorce le long du bord d'une planche.
Les fissures radiales sont les fissures radiales qui se développent dans les billes et sont des défauts de fabrication qui se produisent en raison d’un retrait circonférentiel entraînant une contraction pendant le processus d’assaisonnement.
La déformation fait référence à tout écart par rapport à une surface plane et précise de la planche. Les types de chaîne comprennent la courbure, l’arc, la torsion et l’emboutissage dans le bois.
Le nid d’abeille fait référence aux fissures internes d’une planche qui se produisent en raison d’un assaisonnement inapproprié.
Le grain déchiré résulte d'un bois ébréché ou retiré de la surface de la planche en raison d'une coupe ou d'un rabotage. Ces défauts impactent la résistance du bois.
Des taches de surface peuvent apparaître sur le bois après qu’il a été transformé en bois d’œuvre. Ces taches brunes, vertes ou bleues affectent généralement l’apparence, mais pas la résistance du bois.

défauts du bois

Lumber Defects

Les défauts du bois, qui peuvent affecter à la fois l'apparence et l'intégrité structurelle du bois, comprennent une variété de défauts de croissance et de fabrication. Les défauts de croissance tels que les nœuds et les trous de nœuds se produisent là où les branches étaient autrefois attachées au tronc de l'arbre, et des trous de nœuds se forment lorsque ces nœuds tombent. D'autres défauts naturels comprennent la pourriture et les dommages causés par les insectes, qui compromettent la résistance et la durabilité du bois.

Les fentes sont des fractures mineures qui longent ou traversent les cernes annuels du bois, tandis que la flache est caractérisée par l'absence de bois ou la présence d'écorce le long du bord d'une planche, résultant généralement de la façon dont le bois est coupé. Les gerces sont des fissures radiales dans le bois, qui apparaissent lorsque le bois sèche et rétrécit de manière circonférentielle pendant le processus de séchage.

Le gauchissement est une déviation par rapport à la surface plane du bois et peut se manifester par une courbure, une courbure, une torsion ou un gauchissement, chacun affectant l'utilisabilité du bois. Le nid d'abeilles fait référence aux fissures internes causées par un séchage inapproprié, ce qui peut affaiblir le bois de l'intérieur.

Le grain déchiré est un autre défaut qui se produit pendant le processus de coupe ou de rabotage, où le bois s'écaille, ce qui donne une surface rugueuse. Enfin, des tâches de surface telles que des décolorations brunes, vertes ou bleues peuvent se développer après le traitement. Ces tâches n'affectent généralement que l'apparence du bois et non sa résistance.

Il est essentiel de comprendre ces défauts pour gérer la qualité du bois et s'assurer que le bois répond aux normes nécessaires pour les utilisations dans la construction et la fabrication.

Défauts du bois

Les défauts de croissance du bois comprennent des nœuds, qui se forment là où les branches se connectent au tronc de l’arbre, des trous de nœuds résultant de la chute de nœuds lâches, de la pourriture ...

Education

Enseignement

JoVE Core

Civil Engineering

Génie civil

Unit 1

Unité 1

Wood

Bois

KEY TERMS AND CONCEPTS

TERMES ET CONCEPTS CLÉS

common wood flaws in lumber

Lumber defects are flaws in wood that can change both its appearance and its strength. These defects come from tree growth and from the way lumber is processed. Knowing the main defects helps explain why some boards are better for construction and manufacturing than others.

Some defects begin in the tree itself. Knots form where branches were once attached to the trunk, and knotholes appear when those knots fall out. Decay and insect damage are also natural defects that can weaken wood and reduce its durability.

Other defects come from splitting, cutting, or drying the lumber. Shakes are small fractures that run along or across the annual rings. Wane is the missing wood or bark left along a board edge after cutting. Checks are radial cracks that form as wood dries and shrinks during seasoning, and honeycombing is a set of internal cracks caused by improper seasoning.

Warping changes the flat shape of a board. It can show up as crooking, bowing, twisting, or cupping, and each form can make the lumber harder to use. Torn grain is another processing defect, where the wood chips away during cutting or planing and leaves a rough surface. Surface stains, such as brown, green, or blue discoloration, may also appear after processing. These stains usually affect appearance more than strength.

Common Wood Flaws in Lumber

introduction to wood

Wood Structure and Uses in Building

Wood is a construction material made from trees. A tree trunk has several layers. The outside is a protective layer of dead bark. Under that is living bark, then the cambium, then sapwood. As sapwood matures, it becomes heartwood. The pith sits at the center of the trunk. The age of a tree can be read from its growth rings. These rings are concentric bands seen in a trunk cross-section. Wood strength also depends on grain. Grain refers to elongated, tubular cells that run along the length of...

softwoods and hardwoods

Wood Grain in Softwoods and Hardwoods

Softwoods and hardwoods come from different kinds of trees, and their leaf structures and cell makeup help explain how they are used. Softwoods come from cone-bearing trees with needle-like leaves. Hardwoods usually come from trees that shed broad leaves seasonally. Softwoods are made mostly of long cells called tracheids and a smaller number of rays, which are radial cells. This simpler structure gives softwoods a rougher grain. Because of this, they are often used in construction for...

lumber

Lumber Cutting Methods

Lumber is made from logs that are harvested, debarked, and processed into long pieces with a rectangular cross-section. The process starts when an automated saw slices a log into slabs. Those slabs then move on a conveyor belt to smaller saws, where they are cut into square-edged pieces of specific widths. Freshly cut lumber usually has rough surfaces. Its dimensions may also vary slightly from one end to the other. The way wood is cut affects both the lumber’s appearance and how it is used. <br...

structural properties and dimensions of lumber

structural-properties-and-dimensions-of-lumber

Wood Strength Tests and Lumber Sizes

Wood strength depends on how its fibers are aligned along the length of the tree. This alignment gives wood much greater tensile strength along the grain than across it, sometimes up to twenty times higher. Wood also tends to perform better under compression than under tension. Fiber length varies by wood type. Hardwoods have fibers about one twenty-fifth of an inch long. Softwoods have longer fibers that range from one-eighth to one-third of an inch. Laboratory tests help measure how wood...

seasoning of wood

Wood Drying for Stronger Construction

Seasoning of wood is the drying process used to lower and stabilize moisture content before wood is used in construction. Fresh wood can swell when it takes in moisture and contract as it dries. Seasoning helps reduce that movement so the wood stays more stable after it is built into a structure. The main goal is to reach equilibrium moisture content. This is the point where the wood’s moisture level matches the moisture in the surrounding environment. When wood is seasoned properly, it is...

wood surfacing

Wood Surfacing for Smooth, Safe Lumber

Wood surfacing smooths lumber, improves its size accuracy, and makes it safer to handle. It is a key finishing step in woodworking and construction. The process also helps correct small distortions that can form as wood dries. Before surfacing, the wood may be sized slightly larger to account for shrinkage during seasoning, which is the drying stage. A plane, a tool with rotating blades, is used to remove material and smooth the surface. The same tool can also round the edges a little, which...

lumber defects

Lumber defects are flaws in wood that can change both its appearance and its strength. These defects come from tree growth and from the way lumber is processed. Knowing the main defects helps explain why some boards are better for construction and manufacturing than others. Some defects begin in the tree itself. Knots form where branches were once attached to the trunk, and knotholes appear when those knots fall out. Decay and insect damage are also natural defects that can weaken wood and...

wood fasteners

Wood Fastener Types and Uses

Wood fasteners connect parts of a wood structure and help keep members in place. The strength of the connection depends mainly on direct bearing between the wood members. Different fasteners are chosen for different jobs and structural needs. Nails are the most common wood fasteners. They are sharp-pointed metal pins that are driven into wood with a hammer or a mechanical nail gun. Nails come in many diameters, head styles, and lengths. Nailing methods also matter. Face nailing places the...

veneer

How Veneer Is Cut and Used

Veneer is a thin sheet of wood that is usually about one-eighth of an inch thick or less. It is made to show the look of wood while using timber more efficiently. Veneer is common in furniture and other finished wood products. One common way to make veneer is rotary cutting. In this method, a log is mounted in a large lathe and spun against a knife edge. As the knife moves deeper into the turning log, it peels off a continuous strip of wood. This creates rotary-cut veneer. Other veneer...

wood products

Engineered Wood Products in Construction

Engineered wood products are made from wood strands, veneers, lumber, and even waste wood shreds. They are used in both structural and nonstructural building applications. These materials are designed to improve strength, durability, and versatility in modern construction. Glue-laminated wood, or glulam, is made by bonding several smaller pieces of dimensional lumber with adhesive. Cross-laminated timber uses solid lumber panels with layers placed so the grain direction alternates. This layer...

wood panel products

Types of Wood Panels in Construction

Wood panels are common construction materials used for flooring, siding, and roofing. They usually come in standard 4-foot by 8-foot sheets. Their thickness can range from one-quarter of an inch to one and one-eighth inches. Plywood is one of the most familiar wood panels. It is made by gluing thin wood veneers, or layers, under pressure. The outer veneer grain runs lengthwise, while the inner layers run widthwise. Plywood also has an odd number of layers, which helps keep the panel...

key terms and concepts

Learn the main lumber defects found in wood, from knots and decay to warping, checks, and stains, and how they affect strength and appearance.

Common Wood Flaws in Lumber | JoVE K12

JoVE Core Civil Engineering provides a foundational exploration of essential construction materials in civil engineering, focusing on bricks, stones, steel, wood, and concrete through easy-to-understand animated videos. This collection covers the properties, manufacturing processes, and practical applications of these materials. Additionally, the accompanied science-in-action videos demonstrate the research experiments performed in laboratories.

civil engineering

Common Wood Flaws in Lumber

Description

Transcript

Tags