Name: endpoint detection in potentiometric titration
Uploaded: 2024-12-05T18:31:57.000Z
Duration: 1 min 31 s
Channel: JoVE

ポテンショメトリック滴定は、滴定液の添加後の溶液中の参照電極と指示薬電極の間の電位差を測定することにより、分析種の濃度を決定します。
滴定曲線の急激な変化は、滴定液の体積に対する電位をプロットすることによって得られ、滴定の終点を示します。
さらに、エンドポイントは、1 次導関数曲線の最大値または 2 次導関数曲線のゼロ点から、より正確に識別できます。
電位差滴定には、酸塩基反応、沈殿反応、錯体反応、または酸化還元反応が含まれる場合があります。
酸-塩基滴定では、通常、ガラス電極を使用してpHを測定し、pHを滴定液量に対してプロットしてエンドポイントを特定します。
沈殿滴定は、イオン選択性電極を用いて、沈殿による陰イオンまたは陽イオンの濃度変化から得られる電位をネルンスト方程式で測定します。
イオン選択性電極は、EDTAなどの錯体配位子の付加による金属イオン濃度の変化を記録するために、錯滴定にも使用されます。
酸化還元滴定は、白金のような不活性金属電極を採用しています。電位差滴定曲線をさまざまな視覚指標の曲線と一緒にプロットすると、電位差滴定に代わる視覚指標を開発するのに役立ちます。

電位差滴定: 概要

Potentiometric Titration: Overview

電位差滴定は、溶液中の 2 つの電極間の電位差を測定することで分析物の濃度を決定する定量分析手法です。電位差滴定の終点は、電位差に大きな変化がある点です。これは、分析物と滴定剤の間の化学量論的反応が完了したときに発生します。終点は通常、測定された電位差を滴定剤の添加量の関数としてプロットすることでグラフで決定されます。結果として得られるグラフは滴定曲線と呼ばれます。微分曲線は、滴定剤の添加量に対する滴定曲線の微分をプロットすることで得られます。微分曲線は、終点をより正確に特定するのに役立ちます。微分曲線は通常、終点で最大点または最小点を示し、より正確な終点の決定を可能にします。電位差滴定は非常に汎用性が高く、酸塩基、沈殿、錯滴定、または酸化還元反応に使用できます。酸塩基滴定では、通常、滴定剤の量に対する pH を測定するためにガラス電極を使用します。

対照的に、沈殿滴定では、溶液内の特定のイオンに選択的に反応するように設計されたイオン選択電極を使用します。一方、酸化還元滴定では、白金などの不活性金属電極を使用し、滴定曲線は滴定プロセスに適した視覚的指標を選択するのに役立ちます。錯滴定では、イオン選択電極を使用して、EDTA を追加することで金属イオン濃度の変化を記録します。

電位差滴定は、電位差を測定することにより分析物の濃度を決定する定量的分析技術です...

Education

JoVE Core

Analytical Chemistry

分析化学

Unit 1

ユニット1

Electrochemical Analyses and Redox Titration

電気化学分析および酸化還元滴定

electrochemical-analyses-and-redox-titration

KEY TERMS AND CONCEPTS

主要用語と概念

endpoint detection in potentiometric titration

Potentiometric titration is a quantitative analytical method used to find the concentration of an analyte by measuring the potential difference between two electrodes in a solution. The endpoint is the point where this potential changes sharply. It usually appears when the stoichiometric reaction between the analyte and the titrant is complete.

To find the endpoint, the measured potential difference is plotted against the volume of titrant added. This graph is called a titration curve. A derivative curve can also be made by plotting the change in the titration curve with respect to titrant volume. The endpoint is easier to spot on this curve because it often shows a maximum or minimum at that point.

This method is useful for several kinds of reactions, including acid-base, precipitation, complexometric, and redox titrations. Acid-base titrations often use glass electrodes to measure pH as titrant volume increases. Precipitation titrations use ion-selective electrodes that respond to a specific ion in the solution. Redox titrations use inert metal electrodes such as platinum, and the titration curve can help choose a suitable visual indicator. Complexometric titrations use ion-selective electrodes to track metal-ion concentration as EDTA is added.

Endpoint Detection in Potentiometric Titration

endpoint-detection-potentiometric-titration

electrochemistry: overview

Electrochemistry and Redox Reactions

Electrochemistry connects electrical measurements with chemical reactions, especially oxidation and reduction. It focuses on how electron movement helps explain reaction behavior. Oxidation is the loss of electrons from a substance, and reduction is the gain of electrons. A species with strong electron affinity is an oxidizing agent, or oxidant. A species that donates electrons is a reducing agent, or reductant. These redox steps are often described with half-reactions. When electrons move...

electrodes: overview

Types of Electrodes in Electrochemistry

Electrodes are conductive materials in an electrochemical cell. They allow electron transfer reactions to happen at their surfaces. Electrochemical measurements use them to control and measure current and potential. The working electrode, also called the indicator electrode, is the main sensing electrode. Its potential changes with the analyte concentration and with the activity of the electroactive species. Common indicator electrodes include inert platinum electrodes, silver electrodes that...

interfacial electrochemical methods: overview

interfacial-electrochemical-methods-overview

Static and Dynamic Electrochemical Methods

Static and dynamic electrochemical methods study what happens at the boundary between an electrode and a solution. These interfacial methods focus on the electrode-solution interface rather than the overall properties of the liquid. They are useful in electroanalytical chemistry because they can detect very small changes in analyte concentration. These methods are grouped by whether a nonzero current flows through the cell. Static methods, such as potentiometry, measure the cell potential...

potentiometry: overview

Potentiometry and Electrochemical Cell Potential

Potentiometry measures the potential difference between two electrodes in an electrochemical cell. It does this without drawing significant current, so the solution’s composition is not altered. The method uses an indicator electrode, which exchanges electrons with the analyte solution, and a reference electrode, which keeps a constant potential. Each electrode is placed in a solution that makes up a half-cell. In a common setup, the reference electrode is the anode, or left-hand electrode,...

potentiometry: types of electrodes

Reference and Indicator Electrodes in Potentiometry

Potentiometric measurements use reference electrodes and indicator electrodes to track changes in a solution. A reference electrode gives a stable baseline, while indicator and working electrodes respond to changes in the solution’s composition. The Standard Hydrogen Electrode, or SHE, is a common reference electrode. It keeps a zero potential at all temperatures. However, it needs a continuous supply of hydrogen gas, so it is not practical for routine use. The Saturated Calomel Electrode, or...

potentiometry: membrane electrodes

Membrane Electrodes in Ion Sensing

Membrane electrodes measure ions by using a selective membrane that creates a potential difference across it. This membrane potential is called the asymmetry potential, and it can remain nonzero even when analyte concentrations are the same on both sides of the membrane. The signal usually depends on all ions in the sample that can interact with the membrane, not just one analyte. Selectivity is described by a selectivity coefficient. This value compares the response to an interferent with the...

redox titration: overview

Redox Titration Endpoints and Indicators

Redox titration uses electron transfer in a redox, or reduction-oxidation, reaction to find the concentration of an unknown solution. The titrant has a known concentration, and it is added gradually to the analyte, which is the solution being tested. The endpoint shows when the reaction between the two substances is complete. Before a redox titration begins, the analyte should be in a single oxidation state. If needed, this is done by pre-oxidizing or pre-reducing the sample with an auxiliary...

redox titration: iodimetry and iodometry

Using Iodine to Find Unknown Concentrations

Iodometry and iodimetry use iodine to measure unknown concentrations in redox titrations. These methods help determine the amount of an oxidizing or reducing agent in a sample. The key idea is that iodine changes color and reacts in a known stoichiometric ratio with the analyte. In iodometric titrations, the sample usually contains an oxidizing agent. The solution is acidified and then treated with an excess of iodide ions, which releases an equivalent amount of iodine in equilibrium with...

redox titration: other oxidizing and reducing agents

redox-titration-other-oxidizing-and-reducing-agents

Choosing Oxidizing Titrants in Redox Titration

Redox titrations can use oxidizing titrants other than iodine. Common choices include potassium permanganate (KMnO4), cerium(IV), and potassium dichromate (K2Cr2O7). The best titrant depends on stability, cost, analyte strength, and the reaction rate between the analyte and the titrant. Potassium permanganate is a strong oxidizing titrant in highly acidic solution. It reduces from Mn(VII) to Mn(II) while it oxidizes the analyte to a higher oxidation state. KMnO4 also works as a self-indicator,...

potentiometric titration: overview

Potentiometric titration is a quantitative analytical method used to find the concentration of an analyte by measuring the potential difference between two electrodes in a solution. The endpoint is the point where this potential changes sharply. It usually appears when the stoichiometric reaction between the analyte and the titrant is complete. To find the endpoint, the measured potential difference is plotted against the volume of titrant added. This graph is called a titration curve. A...

end point prediction: gran plot

Gran Plot for Titration Endpoint Prediction

A Gran plot helps predict the endpoint of a potentiometric or acid-base titration before the endpoint is reached. It uses titration data collected only up to a point that is still below the equivalence volume. The data are then transformed into a straight-line format. To build the plot, the line is extended to the x-axis. That x-intercept shows the titrant volume needed to reach the equivalence point. In potentiometric titration, the Gran plot uses the volume-corrected base-10 antilogarithm of...

electrogravimetric analysis: overview

Electrode Weighing in Electrogravimetric Analysis

Electrogravimetric analysis measures an analyte by weighing the material that deposits on an electrode. A pre-weighed working electrode is placed in solution, and a potential is applied. The target substance then deposits by reduction at the cathode or by oxidation at the anode. After electrolysis, the electrode is weighed again. The mass increase gives the weight of the analyte in the solution. To check that deposition is complete, the fresh electrode surface is exposed to the solution while...

coulometry: overview

Coulometry and Electrical Charge Analysis

Coulometry is an analytical method that finds the amount of an analyte by measuring the electrical charge needed for its complete electrolysis. It is known for being rapid, accurate, and precise. Unlike many other methods, it does not require analytical standards. The total charge passed during electrolysis is linked to the amount of analyte through Faraday's laws of electrolysis. For correct coulometric measurements, the charge supplied must match Faraday's constant multiplied by the number...

controlled-potential coulometry: electrolytic methods

controlled-potential-coulometry-electrolytic-methods

Measuring Analyte Charge by Potentiostatic Coulometry

Controlled-potential coulometry measures analyte amount by carefully controlling electrode potential during electrolysis. It is also called potentiostatic coulometry. A potentiostat keeps the working electrode at a set potential in a three-electrode system. The working electrode choice depends on the potential range. Platinum working electrodes are used for positive potentials. Mercury pool electrodes are preferred for very negative potentials. The platinum counter electrode is kept away from...

controlled-current coulometry: overview

Controlled-Current Coulometry in Redox Analysis

Controlled current coulometry is an electrochemical method used to measure the amount of a substance by passing a steady current through a cell. It is also called amperostatic coulometry. The analyte, or substance being analyzed, reacts at the electrode surface as charge moves through the system. The amount of analyte is found by measuring how long it takes for a known charge to pass. This calculation follows Faraday’s laws of electrolysis. A typical setup includes a galvanostat, a...

controlled-current coulometry: coulometric titration

controlled-current-coulometry-coulometric-titration

Electrically Generated Reagents in Titration

Coulometric titrations use an electrically generated reagent to measure the amount of a substance in a sample. The electron acts as the standard reagent, and the result depends on the current and the time used to generate it. The method follows the same basic idea as a regular titration, including endpoint detection. Two conditions are essential for this type of titration. First, the electrode reaction that makes the reagent must be 100% efficient. Second, the generated reagent must react...

voltammetry: overview

Voltammetry for Detecting Redox Species

Voltammetry measures current in an electrochemical cell as the applied potential changes. It is an electroanalytical method used to study redox-active species. The current response is shown on a graph called a voltammogram. A voltammetric cell uses three electrodes: a working electrode, a reference electrode, and an auxiliary electrode. Redox reactions happen at the working electrode, and a potentiostat controls its potential. The reference electrode, such as a saturated calomel electrode or a...

voltammetry: factors affecting measurements

voltammetry-factors-affecting-measurements

Voltammetry and Faradaic Current

Voltammetry measures faradaic current, which is the current created by redox reactions of an analyte at the working and auxiliary electrodes. The current from reduction is called cathodic current and carries a positive charge. The current from oxidation is called anodic current and has a negative charge. The applied potential at the working electrode controls the flow of faradaic current. The size of that current depends on how fast the oxidation or reduction reaction occurs at the electrode...

voltammograms: overview

Voltammogram Shapes and Redox Analysis

Voltammograms are current plots made against applied potential. They help show how an electrochemical system behaves during a redox reaction. The shape of the plot depends on how the current is measured and on whether convection, or fluid movement, is present. When convection is present, as in hydrodynamic voltammetry, the voltammogram usually has a sigmoid shape. In this case, the current rises from a residual current to a limiting current at the analyte’s oxidation or reduction potential.

voltammetric techniques: linear-scan (e vs time)

voltammetric-techniques-linear-scan-e-vs-time

Polarography and Voltammetry with Mercury Drops

Polarography and hydrodynamic voltammetry are voltammetric techniques used to study electrochemical reactions. They track the current that flows as the electrode potential changes. In polarography, the key working electrode is a dropping mercury electrode, or DME. A DME uses a capillary tube filled with mercury. A tiny mercury droplet forms at the tip and then drops away. This gives a fresh electrode surface for each measurement. During the test, the potential applied to the DME changes...

voltammetric techniques: pulse voltammetry

voltammetric-techniques-pulse-voltammetry

Pulse Voltage Methods for Electrochemistry

Pulse voltage methods in electrochemistry use small, timed changes in voltage to measure current. Differential-pulse voltammetry, or DPV, adds short potential pulses to a linear sweep across an electrochemical cell. These pulses are usually in the millivolt range and appear at regular intervals. Each pulse lasts only a few milliseconds. DPV works by creating faradaic current at the electrode surface. Faradaic current comes from redox reactions, where electrons move between the electrode and...

voltammetric techniques: cyclic voltammetry

voltammetric-techniques-cyclic-voltammetry

Reading Redox Peaks with Cyclic Voltammetry

Cyclic voltammetry measures how current changes as the potential at an electrode is varied. It is used to study the redox properties of a chemical species, meaning how easily it is oxidized or reduced. The setup uses three electrodes in an electrolyte solution. The working electrode is where the redox reaction of interest takes place. The reference electrode provides a stable potential, and the counter electrode completes the circuit for current flow. The process starts at a chosen initial...

voltammetry: stripping methods

Trace Analysis by Stripping Voltammetry

Stripping voltammetry is an electrochemical method used to detect trace amounts of analytes in solution. It works by applying a potential to an electrode and measuring the current that results. The current is then used to estimate the analyte concentration. Anodic Stripping Voltammetry, or ASV, is used for metals and metalloids at very low levels. It has two main steps: deposition and stripping. First, a negative potential reduces analyte ions and deposits them on the working electrode surface.

amperometry: overview

Measuring Analytes with Amperometric Sensors

Amperometry measures specific analytes in a solution by tracking the electric current from an electrochemical reaction. A constant potential is applied between a working electrode and a reference electrode. The current that results is proportional to the analyte concentration. The Clark oxygen electrode is a common example of amperometry. It uses a cathode and an anode sealed inside a gas-permeable membrane. The cathode is typically platinum or gold, and the anode is silver. When a potential...

key terms and concepts

Learn how potentiometric titration uses electrode potential, titration curves, and derivative plots to identify endpoints in acid-base, redox, precipitation, and complexometric reactions.

Endpoint Detection in Potentiometric Titration | JoVE K12

JoVE Core 分析化学 は、複雑な化学原理をアニメーションで視覚化することで、SI 単位から NMR 分光法を含むトピックをよりわかりやすくします。実験を撮影した実写動画では、これらの概念が世界中の研究所でどのように応用されているかを取り上げています。

analytical chemistry

Endpoint Detection in Potentiometric Titration

Description

Transcript