Name: boom and rod stress analysis
Uploaded: 2024-03-07T13:22:32.000Z
Duration: 1 min 4 s
Channel: JoVE

ブームと荷重を支えるように設計されたロッドで構成される構造を考えてみましょう。ブームとロッドはピンで接合され、ブラケットとピンで支えられています。
まず、構造物に作用するさまざまな応力を解析するために、ブームとロッドを支持体から切り離し、自由体図を描きます。
平衡方程式を考慮して、ブームとロッドに作用する反力が計算されます。
ポイントPでの反応はブームの圧縮を引き起こし、ポイントRでの反応はロッドの張力を引き起こします。
ブームとロッドがピンQに加える力は、力の三角形を使用して決定できます。
ブームにかかる軸力から生じる垂直応力は、部材にかかる力をブームの断面積で割ることによって計算されます。
ロッドに作用する垂直応力も同様に決定されます。

応力の応用

Applications of Stress

応力を支えるために設計されたブームとロッドで構成される構造物を考えてみましょう。 これら 2 つのコンポーネントはピンで接続され、ブラケットとピンで安定します。 ブームとロッドを支えている器具から取り外して、この構造にかかるさまざまな応力を評価し、自由体図を作成します。 次に、構造に作用する荷重を含め、加えられるすべての力が特定されます。 ブームとロッドの両方にかかる反力は、平衡方程式を使用して計算されます。

点 P での反力はブームに圧縮を引き起こし、点 R での反力はロッドに張力を引き起こします。 両方のメンバーは 2 つの力のメンバーであり、2 点のみで力を受けます。 これら 2 点のそれぞれに作用する合力の作用線は等しく、反対方向であり、両方の点を通過します。 これらの部材によってジョイントに加えられる力は、力の三角形を使用して決定できます。 ブームにかかる軸力から生じる垂直応力は、部材にかかる力をブームの断面積で割ることによって求められます。 同様に、ロッドに作用する垂直応力を計算します。

ブームと荷重を支えるように設計されたロッドで構成される構造を考えてみましょう。ブームとロッドはピンで接合され、ブラケットと...

Education

JoVE Core

Mechanical Engineering

機械工学

Unit 1

ユニット1

Concept of Stress

ストレスの概念

KEY TERMS AND CONCEPTS

主要用語と概念

boom and rod stress analysis

Boom and rod stress analysis shows how a pinned support structure carries a load. The boom and the rod are connected by a pin and held in place by brackets and pins. The structure is then separated from its supports so the forces can be studied clearly.

A free-body diagram is drawn to identify every force on the boom, the rod, and the load. The reaction forces on both members are found using equilibrium equations. At point P, the reaction causes compression in the boom. At point R, the reaction causes tension in the rod.

The boom and the rod are two-force members. That means each member is acted on at only two points. The lines of action of the forces at those points are equal and opposite, and they pass through both points. The forces at the joint can then be found with a force triangle.

Normal stress is calculated from the axial force in each member. For the boom, the stress is the force on the member divided by the boom’s cross-sectional area. The same method is used for the rod to determine the normal stress acting on it.

Boom and Rod Stress Analysis

normal stress

Normal Stress in Axial Loading

Normal stress acts perpendicular to a material’s cross-sectional area. It appears when a force is applied along the axis of an object, which is called axial loading. Bridge truss members are a practical example of this kind of loading. When a rod carries axial load, internal forces develop across the section. Because these forces act normal to the plane of the section, the stress is called normal stress. Stress here means the average stress over the whole cross-section, not the value at one...

shearing stress

Shear Forces in Bolts and Rivets

Shearing stress is caused by transverse forces acting on an object. These forces create internal forces in the plane where the external forces are applied. The total internal force in that section is called the shear. Average shearing stress is found by dividing the shear by the cross-sectional area. This value is only an average, because shear stress is not spread evenly across the section. It can be zero at the surface and much higher than the average in other areas. Bolts, pins, and rivets...

bearing stress

Bolt-to-Plate Contact Pressure

Bearing stress is the contact pressure between two separate bodies. A common example is a bolt pushed through a plate. The bolt applies a force to the plate, and the plate pushes back with an equal and opposite force. That force is not a single point load. It is made up of many smaller forces spread across the contact surface between the bolt and the plate. Because these microforces are complex, engineers use an average value called bearing stress. Bearing stress is found by dividing the...

applications of stress

Boom and rod stress analysis shows how a pinned support structure carries a load. The boom and the rod are connected by a pin and held in place by brackets and pins. The structure is then separated from its supports so the forces can be studied clearly. A free-body diagram is drawn to identify every force on the boom, the rod, and the load. The reaction forces on both members are found using equilibrium equations. At point P, the reaction causes compression in the boom. At point R, the...

stress on an oblique plane

Axial Load Stress on Inclined Sections

Axial loading creates stress in a material along its central axis. This kind of load can cause compression or elongation, and it produces normal stress. Normal stress acts perpendicular to the material area and can be either tensile or compressive. When the section is not perpendicular to the load, it becomes an oblique plane. On this inclined plane, the stress state includes both normal stress and shearing stress. Shearing stress acts parallel to the area and changes shape without changing...

stress: general loading conditions

Stress Components on a Loaded Body

Stress components on a loaded body can be found by cutting the body through a point with a plane parallel to the xy plane. That section carries the original loads, along with normal forces and shearing forces. The result is a simple way to describe how a structure responds under combined loading. The shearing force in the section can point in different directions within the plane. It is split into two parts that run parallel to the x and y axes. Each part is divided by the area, and as that...

components of stress

Stress Components on a Cube at a Point

Stress components on a small cube help describe how a body behaves under multiple loading. The cube is centered at point O and has stress acting on all six faces, whether the faces are visible or hidden. Normal stress components σx, σy, and σz act perpendicular to the x, y, and z axes. Shearing stress components also act on the cube faces. The visible faces carry shear stresses such as τxy and τxz. The hidden faces carry equal and opposite stresses. This balance keeps the cube in equilibrium.

design consideration

Safety Factors in Structural Design

Safety factors in structural design help engineers choose a material and loading limit that can be used safely. The process begins with a material’s ultimate strength. This value comes from tests that increase force until the material reaches its breaking point or limit. The ultimate load is then divided by the original cross-sectional area to find the ultimate normal stress, or strength. Ultimate shearing stress is another key value used in design. These limits show how much stress a material...

key terms and concepts

Analyze a boom-and-rod support structure, draw a free-body diagram, find reaction forces, and calculate compression, tension, and normal stress.

Boom and Rod Stress Analysis | JoVE K12

JoVE Core 機械工学は、平衡、力、トラス解析、構造力学などの重要なトピックをカバーする簡潔でわかりやすいアニメーション ビデオを提供します。実際のアプリケーションを探索し、科学者主導の実験を通じてこれらのコンセプトが実際に動作しているのを目撃してください。

mechanical engineering

Boom and Rod Stress Analysis

Description

Transcript

Tags