Name: dual diode wave clipping
Uploaded: 2024-07-08T13:20:21.000Z
Duration: 1 min 18 s
Channel: JoVE

クリッパー回路は、ダイオードを使用して波形を変更する波形整形ツールです。
これらの回路は、テレビ、レーダー送信機、および受信機で一般的です。
2つの理想ダイオードで構成され、それぞれがバイアス電池と抵抗器に接続されたデュアルクリッパー回路を考えてみましょう。
入力AC信号の正の半サイクルの間、ダイオードD1は入力信号によって順バイアスされ、バイアス電池によって逆バイアスされます。対照的に、ダイオードD2は両方によって逆バイアスされています。
入力電圧がバイアス電圧より小さい場合、ダイオードD1はオープンスイッチとして機能し、出力は同じ印加電圧を反映します。
ただし、入力電圧がバイアス電圧を超えると、ダイオードD1が順方向バイアスになり、入力電圧がブロックされ、出力に信号が残りません。
負の半サイクルの場合、ダイオードD2が信号をクリッピングし、出力電圧がD2のバイアス電圧によって制限されるという同様のプロセスが発生します。
抵抗値は、適切な順方向ダイオード電流と逆方向ダイオード電流による電圧降下を最小限に抑えるために細心の注意を払って選択されます。

クリッパ回路

クリッパ回路は、ダイオードの独自の特性を利用して波形特性を変更および制御する基本的な波形整形装置です。この技術は、電子機器、特にテレビやレーダー通信システムで広く使用されており、送信機と受信機の両方で波形変調を強化します。

クリッパ回路の動作は、2 つの理想ダイオードを統合した二重クリッパ構成セットアップを分析することで例示できます。各ダイオードはバイアス電池とペアになっており、抵抗器と並列に配置されています。回路の動作は、入力 AC 信号の位相によって異なります。正の半周期の間、入力電圧がダイオード A に接続されたバッテリー電圧よりも低い場合、回路は開いたスイッチのように動作し、印加電圧を変更せずに通過させます。
クリッピング動作は、入力電圧がバイアス電池の電圧を超えると明らかになります。このような状況では、ダイオード A は順方向バイアス状態に移行し、入力電圧に対するバリアとして効果的に機能します。出力電圧は、バイアス電池電圧に等しい一定値にクリップされ、ダイオード B は逆バイアスされたままになります。
負の場合、ダイオード B がクリッピングの役割を果たします。結果として生じる出力電圧は、ダイオード B のバイアス電圧によって制限されます。抵抗値の選択は重要であり、逆電流による電圧降下の影響を最小限に抑えながら、ダイオードに十分な順方向電流を確保するバランスを取ることを目指します。このようなメカニズムにより、クリッパ回路は波形操作のための堅牢なツールを提供し、電子システムのパフォーマンスと効率を向上させます。

クリッパー回路は、ダイオードを使用して波形を変更する波形整形ツールです。
これらの回路は、テレビ、レーダー送信機、および受信機で一般的です。
...

Education

JoVE Core

Electrical Engineering

電気工学

Unit 1

ユニット1

Diodes

ダイオード

KEY TERMS AND CONCEPTS

主要用語と概念

Clipper Circuit

dual diode wave clipping

Dual diode wave clipping uses diodes and biasing batteries to reshape an AC signal. A clipper circuit is a wave-shaping device that changes waveform parts without changing the whole signal. It is commonly used in television and radar communication systems to improve waveform modulation in transmitters and receivers.

A dual-clipper setup uses two ideal diodes, two biasing batteries, and a resistor connected in parallel. The circuit works by responding to the phase of the input AC signal. The resistor value must be chosen carefully. It should allow enough forward current for the diode, while limiting the effect of voltage drop from reverse current flow.

During the positive half-cycle, diode A controls the output when the input voltage rises above the battery voltage connected to it. Before that point, when the input voltage is lower, diode A behaves like an open switch and the input passes through unchanged. Once the bias level is exceeded, diode A becomes forward-biased and the output is clipped to the battery voltage. At the same time, diode B stays reverse-biased.

During the negative half-cycle, diode B performs the clipping action. The output is then limited by the biasing voltage of diode B. In this way, the circuit constrains both positive and negative peaks and provides a practical tool for waveform control in electronic systems.

Dual Diode Wave Clipping

the ideal diode

Ideal Diode I-V Curve and Rectification

An ideal diode is a simple model of a semiconductor diode used to show how current moves through circuits. A diode has two terminals. The anode is positive, and the cathode is negative. In this model, current can flow only in one direction. When a positive voltage is applied to the anode relative to the cathode, the diode is forward-biased. In that state, it conducts current. When the cathode is at a higher potential than the anode, the diode is reverse-biased. It then blocks current and acts...

diode: forward bias

Diode Current in Forward Bias

Diode current in forward bias depends on how the p-type and n-type regions are connected to a battery. When the p-type region is tied to the positive terminal and the n-type region to the negative terminal, the diode is forward-biased. This setup lowers the potential barrier inside the diode and lets current move easily from the p-type side to the n-type side. The current-voltage behavior of a forward-biased diode is described by its I-V characteristics. These characteristics depend on the...

diode: reverse bias

Diode Reverse Current and Breakdown

A diode in reverse bias blocks current flow and widens its depletion region. In this setup, the positive terminal of the power source connects to the n-type material, and the negative terminal connects to the p-type material. The reverse connection also raises the barrier potential, so current stays very small. The small reverse current is called leakage current. It comes mainly from minority charge carriers. At room temperature, once the reverse voltage is above the thermal voltage, the...

zener diodes

Zener Diode Voltage Regulation

Zener diodes are semiconductor devices used to hold voltage steady in reverse bias. In reverse breakdown, current flows into the cathode and makes it positive relative to the anode. This behavior is different from a conventional diode and is the reason Zener diodes are useful in voltage regulation. A Zener diode has a nearly vertical current-voltage, or I-V, curve above a threshold called the knee current. That shape lets it keep a fairly stable voltage over a wide range of currents.

modeling of diode forward characteristics

modeling-of-diode-forward-characteristics

Diode Forward Bias: I-V Curve and Models

Diode forward bias is analyzed with the current-voltage, or I-V, curve and two common circuit models. These models help describe how a diode behaves when current flows in the forward direction. They are useful for electronic circuit design and analysis. The exponential diode model is used when the source voltage rises above 0.5 volts. At that point, the diode current increases exponentially above the saturation current. The I-V curve shows this nonlinear response as the forward voltage...

small-signal diode model

Diode Bias and Small-Signal Response

Diode bias and small-signal response describe how a diode behaves when a steady DC voltage and a tiny changing signal act on the same circuit. The DC bias sets the diode’s operating point, or Q point. Around that point, the diode current and voltage follow an exponential I-V relationship. A small time-varying signal can be added on top of the DC bias to study how the diode responds to small changes. When the signal voltage is much smaller than the thermal voltage, the diode’s behavior can be...

modeling of diode reverse characteristics

modeling-of-diode-reverse-characteristics

Zener Diode Load-Line Modeling

Zener diode load-line modeling shows how a reverse-biased diode sets a steady voltage in a circuit. Zener diodes use reverse breakdown in a controlled way, so they can hold a fixed voltage across their terminals. This makes them useful for voltage regulation. When the reverse voltage rises above the Zener voltage, or VZ, the diode enters the breakdown region. In this region, the current-voltage, or I-V, curve becomes nearly vertical after the knee current, IZ, is reached. That means the...

half wave rectifier

Single-Diode AC to DC Conversion

Single-diode AC to DC conversion uses a half-wave rectifier to change alternating current into a unidirectional voltage. The circuit is simple. It uses one diode in series with a load resistor and an AC power source. The diode controls the current because it allows flow in only one direction. During the positive half-cycles of the AC input, the diode is forward-biased. When the input voltage is greater than the diode threshold, current flows and an output voltage appears across the load...

full wave rectifier

AC to DC Conversion with Full-Wave Rectifiers

A full-wave rectifier converts alternating current, or AC, into direct current, or DC. It is more efficient than a half-wave rectifier. The circuit usually uses a center-tapped transformer, two diodes, and a load resistor. The center-tapped transformer is the key part of the circuit. Its secondary winding is split into two equal voltages with opposite polarities. That split lets the rectifier use both halves of the AC input waveform. During the positive half-cycle of the AC signal, diode D1...

bridge rectifier

AC to DC Conversion with Bridge Diodes

A bridge rectifier converts alternating current (AC) into direct current (DC) using four diodes arranged in a bridge layout. It is used to turn both halves of the AC waveform into a single-direction output. That makes it an important part of many electronics circuits. During the positive half-cycle, diodes D1 and D2 conduct. Current then flows through the load resistor R. At the same time, D3 and D4 are reverse-biased, so they do not conduct. The action switches during the negative half-cycle.

clipper circuit

Dual diode wave clipping uses diodes and biasing batteries to reshape an AC signal. A clipper circuit is a wave-shaping device that changes waveform parts without changing the whole signal. It is commonly used in television and radar communication systems to improve waveform modulation in transmitters and receivers. A dual-clipper setup uses two ideal diodes, two biasing batteries, and a resistor connected in parallel. The circuit works by responding to the phase of the input AC signal. The...

clamper circuit

DC Restorer for Waveform Level Shifting

A clamper circuit, or DC restorer, shifts a waveform up or down by adding a DC level. It is a special form of rectifier circuit. In this setup, the output is taken across the diode instead of across the capacitor. The circuit works well with square wave inputs and other pulse signals. The diode direction lets the capacitor charge to the most negative peak of the input signal. After that, the diode stops conducting. The capacitor then holds that voltage at a steady value. As a result, the...

voltage doubler circuit

How a Voltage Doubler Raises AC Output

A voltage doubler circuit raises the output voltage by using a clamping section and a rectifier section. The clamping section includes a capacitor, C1, and a diode, D1. The rectifier section includes a second diode, D2, and a capacitor, C2. The circuit starts working when a sinusoidal input signal enters the clamping section. Under ideal conditions, this stage clamps the positive peaks at zero volts. It also lets the negative peak reach a magnitude that is twice the input amplitude. That...

schottky barrier diode

Fast Switching in Schottky Diodes

Schottky barrier diodes use a metal-semiconductor junction to control current flow. They are built by combining a metal layer with a moderately doped n-type semiconductor. This contact creates the Schottky barrier, which gives the diode its one-way current behavior. When the metal touches the semiconductor, charge transfer occurs. The Fermi levels of the two materials align, and a depletion region forms near the contact area. In an n-type semiconductor, this region contains uncompensated...

key terms and concepts

Learn how a dual-clipper circuit uses ideal diodes, biasing batteries, and a resistor to trim AC signal peaks in TV and radar systems.

Dual Diode Wave Clipping | JoVE K12

JoVE Core 電気工学 は、電気回路の基本概念と回路解析テクニックを網羅したアニメーションビデオシリーズです。オペアンプと回路変換および 1 次・ 2 次回路の概念を網羅しています。実験を撮影した実写動画では、設計例や現代社会での応用が含まれており、複雑な概念も分かりやすく学習いただけます。

electrical engineering

Dual Diode Wave Clipping

Description

Transcript

Tags