Name: power from multiple ac sources
Uploaded: 2024-07-08T13:19:54.000Z
Duration: 1 min 19 s
Channel: JoVE

두 개의 정현파 전압 소스가 있는 회로를 고려하십시오.
중첩 원리에 따르면 두 소스에서 발생하는 총 전류는 각 소스로 인해 독립적으로 발생하는 전류의 합입니다.
또한 순간 전력은 순간 전류의 제곱에 저항을 곱한 값입니다.
이를 한 기간에 걸쳐 적분하면 각 소스로 인한 평균 전력의 합과 같은 평균 전력과 세 번째 항이 생성되며, 이는 주파수가 다른 소스에 대해 0과 같습니다.
단순화된 방정식은 전력 중첩 원리를 의미하며, 서로 다른 주파수를 가진 소스가 전달하는 평균 전력은 각 소스가 전달하는 평균 전력의 합과 같다는 것을 나타냅니다.
이 원칙은 라디오 방송과 같은 통신에서 매우 중요합니다.
여러 라디오 방송국이 동시에 신호를 방송하며 각 방송국은 전자기파의 독립적인 소스로 작동합니다.
전력 중첩 원리에 따르면 라디오가 수신하는 총 전력은 각 스테이션에서 전송하는 전력의 합입니다.
라디오를 특정 주파수로 조정하면 사용자는 여러 방송국에서 신호를 수신하더라도 한 번에 하나의 방송국을 들을 수 있습니다.

 거듭제곱 중첩 원리

두 개의 정현파 전압 소스가 있는 회로를 고려해 보세요. 각각은 회로에 독립적으로 영향을 미치며 중첩 원리는 각 소스의 응답을 합산하여 결합된 효과를 이해하는 데 도움이 됩니다.
<img alt="Figure 1" src="/files/ftp_upload/15124/15124_Figure_1.svg" style="height: 150px;">
중첩 원리에 따르면, 두 소스로 인한 총 전류는 독립적으로 각 소스로 인한 전류의 합입니다. 두 소스가 함께 작동하면 개별 전류(i_1 및 i_2)가 합산되어 총 전류가 생성됩니다. 또한 순시 전력은 순시 전류에 저항을 곱한 값입니다.
<img alt="Equation 1" src="/files/ftp_upload/15124/15124_Equation_1.svg" style="height: 20px;">
이 개념은 에너지가 사용되는 비율인 전력에도 적용됩니다. 특정 순간에 회로의 순간 전력은 전류의 제곱에 저항을 곱한 값입니다. 이것을 한 주기에 걸쳐 적분하면 평균 전력이 나오며, 이는 각 소스로 인한 평균 전력의 합과 같고, 세 번째 항은 서로 다른 주파수를 갖는 소스에 대해 0이 됩니다.
<img alt="Equation 2" src="/files/ftp_upload/15124/15124_Equation_2.svg" style="height: 45px;">
<img alt="Equation 3" src="/files/ftp_upload/15124/15124_Equation_3.svg" style="height: 45px;">
단순화된 방정식은 서로 다른 주파수를 갖는 소스에서 전달되는 평균 전력이 각 소스에서 전달되는 평균 전력의 합과 같다는 전력 중첩 원리를 나타냅니다. 이 원칙은 라디오 방송과 같은 통신에서 매우 중요합니다. 여러 라디오 방송국이 신호를 동시에 방송하며 각각은 독립적인 전자기파 소스 역할을 합니다. 전력 중첩 원리에 따르면, 무선이 수신하는 총 전력은 각 기지국에서 전송되는 전력의 합이 됩니다. 라디오를 특정 주파수에 맞추면 사용자는 여러 방송국에서 신호를 수신하더라도 한 번에 하나의 방송국을 들을 수 있습니다.

두 개의 정현파 전압 소스가 있는 회로를 고려하십시오.
중첩 원리에 따르면, 두 소스에서 발생하는 총 전류는 합계 ...

Education

교육

JoVE Core

Electrical Engineering

전기공학

Unit 1

제1단원

AC Steady State Power

교류 정상 상태 전력

KEY TERMS AND CONCEPTS

주요 용어 및 개념

The Power Superposition Principle

power from multiple ac sources

Power from multiple AC sources is found by adding the effects of each source separately. In a circuit with two sinusoidal voltage sources, each source acts independently. The superposition principle says the total current is the sum of the currents produced by each source alone. If those currents are labeled i1 and i2, they combine to give the total current.

Instantaneous power is the power at one moment in time. In this circuit, it equals the square of the instantaneous current times the resistance. To find the average power, this expression is integrated over one period. The result shows that the average power from both sources is the sum of the average powers from each source, and a third term becomes zero when the sources have different frequencies.

This idea is called the power superposition principle. It means that the average power delivered by sources with different frequencies is the sum of the average power delivered by each source. The principle is important in telecommunications, including radio broadcasting. Multiple radio stations can broadcast at the same time, and each one acts as an independent source of electromagnetic waves. A radio receives the total power from all of them, but tuning to one frequency lets the listener hear one station at a time.

Power from Multiple AC Sources

instantaneous power

AC Power and Phase Shift

Instantaneous power in an electrical circuit comes from the voltage across an element and the current through it. It is written as p(t) and follows the passive sign convention. For sinusoidal input, this product helps show how power changes at each moment. When instantaneous power is expanded, it has two parts. One part is constant and depends on the phase difference between voltage and current. The other part is a sinusoidal term that varies at twice the frequency of the voltage or current. <br...

average power

Power Consumption in AC Circuits

Power consumption in AC circuits is often described with average power. In practical electrical work, the changing value of instantaneous power is less useful than the average over a time period. Average power is found by integrating instantaneous power over that time and then dividing by the duration. The time-domain expression for average power comes from simplifying the equation for instantaneous power. In that form, one cosine term averages to zero over a complete cycle. The result does...

effective value of a periodic waveform

RMS Value for AC Power Measurement

The RMS value, or effective value, helps measure how much power a periodic voltage or current can deliver. It is the direct current, or DC, value that gives the same average power to a resistor as the periodic signal does. This idea is especially important in AC circuits. To find the effective value of current, calculate the root mean square, or RMS, current. First square the instantaneous current values over one period. Then find the mean of those squared values and take the square root. The...

complex power

Power Triangle in AC Circuits

Power triangle and complex power help describe how an AC load uses energy. Engineers use complex power to capture the combined effect of parallel loads. It gives a full picture of the power consumed by a specific load. Complex power is found by multiplying voltage by the complex conjugate of current. Using rms values, it is written with the rms voltage phasor and the complex conjugate of the rms current phasor. It can also be written in terms of load impedance. The magnitude of complex power...

conservation of ac power

AC Power in Series and Parallel Circuits

AC power in series and parallel circuits follows a power preservation rule. In AC circuits, the complex power, real power, and reactive power produced by the source are equal to the total complex, real, and reactive powers absorbed by the loads. When two load impedances are connected in parallel to an AC source V, the source power can be written as the sum of the complex powers delivered to loads Z1 and Z2. If those same loads are connected in series with the voltage source, the complex power...

power factor

Power Factor and AC Load Behavior

Power factor describes how voltage and current behave in an AC load. It is the ratio of average, or active, power to apparent power. The power factor angle is the phase difference between voltage and current, and the cosine of that angle gives the power factor. It also matches the angle of the load impedance. Power factor shows how much apparent power becomes real, or average, power. Its value ranges from zero to one. When a load is purely resistive, voltage and current are in phase. In that...

power factor correction

Reducing Reactive Power in AC Loads

Power factor correction helps AC systems use electrical power more efficiently. In a factory circuit, transmitted power includes apparent power, which is made of active power and reactive power. Power factor is the ratio of real power, measured in kW, to apparent power, measured in kVA. It shows how much of the supplied power becomes useful work. A low power factor often happens when an inductive load draws too much reactive power. This creates a lagging power factor. It can also cause large...

the power superposition principle

Power from multiple AC sources is found by adding the effects of each source separately. In a circuit with two sinusoidal voltage sources, each source acts independently. The superposition principle says the total current is the sum of the currents produced by each source alone. If those currents are labeled i1 and i2, they combine to give the total current. Instantaneous power is the power at one moment in time. In this circuit, it equals the square of the instantaneous current times the...

the maximum power transfer theorem

Matching Load Impedance for Maximum Power

Maximum power transfer in an AC circuit depends on matching the load impedance to the Thevenin equivalent of the source network. The load draws current, and the circuit delivers power to that load. To analyze the current, the voltages, currents, network impedance, and load impedance are written in rectangular form. The average power delivered to the load comes from the square of the current multiplied by the load resistance. To find the condition for maximum power, the power is differentiated...

key terms and concepts

Learn how superposition adds currents from two sinusoidal sources and why average power from different frequencies can be combined in AC circuits and radio.

Power from Multiple AC Sources | JoVE K12

JoVE Core Electrical Engineering offers easy-to-understand animated videos that cover fundamental concepts of electric circuits along with circuit analysis techniques. It incorporates first-order and second-order circuits using operational amplifiers and circuit transformation concepts. The inclusion of practical design examples and real-world applications through scientist-in-action videos adds significant educational value, making complex concepts accessible.

electrical engineering

Power from Multiple AC Sources

Description

Transcript

Tags