Name: boom and rod stress analysis
Uploaded: 2024-03-07T13:22:32.000Z
Duration: 1 min 4 s
Channel: JoVE

하중을 지탱하도록 설계된 붐과 로드로 구성된 구조를 생각해 보십시오. 붐과 로드는 핀으로 결합되고 브래킷과 핀으로 지지됩니다.
먼저 구조물에 작용하는 다양한 응력을 분석하기 위해 붐과 로드를 지지대에서 분리하고 자유물체 다이어그램을 그립니다.
평형 방정식을 고려하여 붐과 로드에 작용하는 반력이 계산됩니다.
P 지점에서의 반응은 붐의 압축을 유발하고 R 지점의 반응은 로드에 장력을 유발합니다.
붐과 로드가 핀 Q에 가하는 힘은 힘 삼각형을 사용하여 결정할 수 있습니다.
붐에 가해지는 축방향 힘으로 인해 발생하는 수직 응력은 부재에 가해지는 힘을 붐의 단면적으로 나누어 계산합니다.
막대에 작용하는 수직 응력도 비슷하게 결정됩니다.

스트레스의 적용

Applications of Stress

하중을 지지하도록 설계된 붐과 로드로 구성된 구조를 생각해 보세요. 이 두 구성 요소는 핀으로 연결되고 브래킷과 핀으로 고정됩니다. 붐과 로드는 지지대에서 분리되어 이 구조에 가해지는 다양한 응력을 평가하고 자유물체 다이어그램을 그립니다. 그런 다음 구조에 작용하는 하중을 포함하여 가해지는 모든 힘이 식별됩니다. 붐과 로드 모두에 가해지는 반력은 평형 방정식을 사용하여 계산됩니다.

P 지점의 반력은 붐에 압축을 일으키고 R 지점의 반력은 로드에 장력을 유발합니다. 두 구성원 모두 두 힘의 구성원이며 두 지점에서만 힘을 받습니다. 이 두 지점 각각에 작용하는 합력의 작용선은 동일하고 반대이며 두 지점을 통과합니다. 이러한 부재에 의해 관절에 가해지는 힘은 힘 삼각형을 사용하여 결정할 수 있습니다. 붐의 축방향 힘으로 인해 발생하는 수직 응력은 부재에 가해지는 우세한 힘을 붐의 단면적으로 나누어 결정됩니다. 마찬가지로 막대에 작용하는 수직 응력이 계산됩니다.

하중을 지탱하도록 설계된 붐과 로드로 구성된 구조를 생각해 보십시오. 붐과 로드는 핀으로 결합되고 브래킷으로 지지되며 ...

Education

교육

JoVE Core

Mechanical Engineering

기계공학

Unit 1

제1단원

Concept of Stress

스트레스의 개념

KEY TERMS AND CONCEPTS

주요 용어 및 개념

boom and rod stress analysis

Boom and rod stress analysis shows how a pinned support structure carries a load. The boom and the rod are connected by a pin and held in place by brackets and pins. The structure is then separated from its supports so the forces can be studied clearly.

A free-body diagram is drawn to identify every force on the boom, the rod, and the load. The reaction forces on both members are found using equilibrium equations. At point P, the reaction causes compression in the boom. At point R, the reaction causes tension in the rod.

The boom and the rod are two-force members. That means each member is acted on at only two points. The lines of action of the forces at those points are equal and opposite, and they pass through both points. The forces at the joint can then be found with a force triangle.

Normal stress is calculated from the axial force in each member. For the boom, the stress is the force on the member divided by the boom’s cross-sectional area. The same method is used for the rod to determine the normal stress acting on it.

Boom and Rod Stress Analysis

normal stress

Normal Stress in Axial Loading

Normal stress acts perpendicular to a material’s cross-sectional area. It appears when a force is applied along the axis of an object, which is called axial loading. Bridge truss members are a practical example of this kind of loading. When a rod carries axial load, internal forces develop across the section. Because these forces act normal to the plane of the section, the stress is called normal stress. Stress here means the average stress over the whole cross-section, not the value at one...

shearing stress

Shear Forces in Bolts and Rivets

Shearing stress is caused by transverse forces acting on an object. These forces create internal forces in the plane where the external forces are applied. The total internal force in that section is called the shear. Average shearing stress is found by dividing the shear by the cross-sectional area. This value is only an average, because shear stress is not spread evenly across the section. It can be zero at the surface and much higher than the average in other areas. Bolts, pins, and rivets...

bearing stress

Bolt-to-Plate Contact Pressure

Bearing stress is the contact pressure between two separate bodies. A common example is a bolt pushed through a plate. The bolt applies a force to the plate, and the plate pushes back with an equal and opposite force. That force is not a single point load. It is made up of many smaller forces spread across the contact surface between the bolt and the plate. Because these microforces are complex, engineers use an average value called bearing stress. Bearing stress is found by dividing the...

applications of stress

Boom and rod stress analysis shows how a pinned support structure carries a load. The boom and the rod are connected by a pin and held in place by brackets and pins. The structure is then separated from its supports so the forces can be studied clearly. A free-body diagram is drawn to identify every force on the boom, the rod, and the load. The reaction forces on both members are found using equilibrium equations. At point P, the reaction causes compression in the boom. At point R, the...

stress on an oblique plane

Axial Load Stress on Inclined Sections

Axial loading creates stress in a material along its central axis. This kind of load can cause compression or elongation, and it produces normal stress. Normal stress acts perpendicular to the material area and can be either tensile or compressive. When the section is not perpendicular to the load, it becomes an oblique plane. On this inclined plane, the stress state includes both normal stress and shearing stress. Shearing stress acts parallel to the area and changes shape without changing...

stress: general loading conditions

Stress Components on a Loaded Body

Stress components on a loaded body can be found by cutting the body through a point with a plane parallel to the xy plane. That section carries the original loads, along with normal forces and shearing forces. The result is a simple way to describe how a structure responds under combined loading. The shearing force in the section can point in different directions within the plane. It is split into two parts that run parallel to the x and y axes. Each part is divided by the area, and as that...

components of stress

Stress Components on a Cube at a Point

Stress components on a small cube help describe how a body behaves under multiple loading. The cube is centered at point O and has stress acting on all six faces, whether the faces are visible or hidden. Normal stress components σx, σy, and σz act perpendicular to the x, y, and z axes. Shearing stress components also act on the cube faces. The visible faces carry shear stresses such as τxy and τxz. The hidden faces carry equal and opposite stresses. This balance keeps the cube in equilibrium.

design consideration

Safety Factors in Structural Design

Safety factors in structural design help engineers choose a material and loading limit that can be used safely. The process begins with a material’s ultimate strength. This value comes from tests that increase force until the material reaches its breaking point or limit. The ultimate load is then divided by the original cross-sectional area to find the ultimate normal stress, or strength. Ultimate shearing stress is another key value used in design. These limits show how much stress a material...

key terms and concepts

Analyze a boom-and-rod support structure, draw a free-body diagram, find reaction forces, and calculate compression, tension, and normal stress.

Boom and Rod Stress Analysis | JoVE K12

JoVE Core Mechanical Engineering offers concise, easy-to-understand animated videos covering key topics such as equilibrium, forces, truss analysis, and structural mechanics. Explore their real-world applications, and witness these concepts in action through scientist-led experiments.

mechanical engineering

Boom and Rod Stress Analysis

Description

Transcript

Tags