Name: shearing stress pattern in a narrow beam
Uploaded: 2024-05-23T12:59:49.000Z
Duration: 1 min 11 s
Channel: JoVE

빔의 요소 단면은 응력의 분포를 해석하기 위해 고려됩니다. 요소의 수평면에 가해지는 전단력의 크기는 수평 전단 표현식에서 구합니다.
해당 면의 평균 전단 응력은 수평 전단을 면의 면적으로 나누어 결정됩니다.
빔 단면의 횡면과 수평면에 대한 전단 응력은 동일하며, 이는 빔 상부의 선을 따라 평균 응력을 나타냅니다. 전단 응력은 힘이 가해지지 않기 때문에 위쪽 면과 아래쪽 면에서 0입니다.
좁은 직사각형 빔에서 빔 섹션의 너비를 따른 전단 응력은 너비가 깊이의 1/4 미만이기 때문에 평균 전단 응력의 0.8% 미만으로 변합니다.
따라서 평균 전단 응력 방정식은 단면을 가로지르는 모든 지점에서 전단 응력을 결정하는 데 사용됩니다.
직사각형 빔의 횡단면에서 전단 응력은 포물선으로 분포되며 상단과 하단에서 응력이 0입니다.

좁은 직사각형 빔의 응력 분포

Distribution of Stresses in a Narrow Rectangular Beam

빔 응력 분포를 연구하려면 요소 단면을 검토하는 것이 필수적입니다. 이 면의 평균 전단 응력을 결정하기 위해 계산된 전단을 표면적으로 나눕니다. 중요한 것은 빔의 가로 평면과 수평 평면의 전단 응력이 서로 대칭되어 빔의 상부 영역을 따라 일관된 응력 분포를 나타냅니다. 특히, 빔의 상부 및 하부 표면에는 힘이 가해지지 않기 때문에 전단 응력이 없습니다.

좁은 직사각형 단면을 가진 빔의 경우 폭에 따른 전단 응력의 변화는 평균 응력의 0.8% 미만으로 최소화됩니다. 이러한 사소한 변화는 빔의 폭이 깊이보다 상당히 작기 때문에 발생하며, 평균 전단 응력 방정식은 빔 단면의 모든 지점에서 응력을 평가하는 신뢰할 수 있는 방법입니다. 직사각형 빔의 횡단면에서 전단 응력은 포물선형으로 분포됩니다. 이 분포는 빔의 상단과 하단 가장자리에 응력이 0이고 중앙으로 갈수록 응력이 증가하는 것이 특징입니다. 이 포물선형 응력 프로파일은 빔이 응력을 관리하는 방법을 이해하고 안정성을 손상시키지 않으면서 구조적 무결성과 하중을 견딜 수 있는 능력을 보장하는 데 필수적입니다.

빔의 요소 단면은 응력의 분포를 해석하기 위해 고려됩니다. 수평에 가해지는 전단력의 크기 ...

distribution-of-stresses-in-a-narrow-rectangular-beam

Education

교육

JoVE Core

Mechanical Engineering

기계공학

Unit 1

제1단원

Shearing Stresses in Beams and Thin-Walled Members

보 및 박판 부재의 전단 응력

shearing-stresses-in-beams-and-thin-walled-members

KEY TERMS AND CONCEPTS

주요 용어 및 개념

shearing stress pattern in a narrow beam

Shearing stress in a narrow rectangular beam is found by studying a small elemental section of the beam. The average shearing stress on that face is calculated by dividing the shear by the surface area. This gives a simple way to describe how the load is spread through the beam.

The shearing stresses on the beam&amp;#39;s transverse and horizontal planes match each other. That means the stress pattern is consistent in the upper region of the beam. Shearing stress is also absent at the top and bottom surfaces, because no applied forces act there.

For a narrow rectangular cross-section, the change in shearing stress across the width is very small. It is less than 0.8% of the average stress. Because the beam is much wider in depth than in width, the average shearing stress equation works well at any point in the cross-section.

Across the rectangular beam&amp;#39;s transverse section, the shearing stress follows a parabolic shape. A parabolic distribution curves upward from the edges to the center. Stress is zero at the top and bottom edges and rises toward the middle. This pattern helps explain how beams carry load while staying structurally stable.

Shearing Stress Pattern in a Narrow Beam

shear on the horizontal face of a beam element

shear-on-the-horizontal-face-of-a-beam-element

Beam Shear Flow from Bending Moments

Beam shear flow comes from the horizontal shear that acts on a prismatic beam element. The element is also acted on by vertical shear forces and normal forces. To study this behavior, the beam is divided into upper and lower sections by the neutral axis. The force balance on the small element is written with an equilibrium equation. That step reveals the horizontal shearing force. This force is tied to the bending moments and to the cross-section’s first moment of inertia. The same result is...

distribution of stresses in a narrow rectangular beam

Shearing stress in a narrow rectangular beam is found by studying a small elemental section of the beam. The average shearing stress on that face is calculated by dividing the shear by the surface area. This gives a simple way to describe how the load is spread through the beam. The shearing stresses on the beam&amp;#39;s transverse and horizontal planes match each other. That means the stress pattern is consistent in the upper region of the beam. Shearing stress is also absent at the top and...

shearing stresses in a beam: problem solving

shearing-stresses-in-a-beam-problem-solving

Beam Shear Stress Analysis and Safety Check

Beam shear stress analysis shows how loads create internal stress in a cantilever beam with a rectangular cross-section. The beam in this problem carries both a distributed load and a point load. The goal is to find the shearing stress at key points and check whether the beam stays within a safe limit. The first step is to identify all loads acting on the beam. Next, the reactions at the fixed end are found using equilibrium equations. The vertical reaction combines the distributed load and...

plastic deformations

Cantilever Beam Yield and Failure

Cantilever beams show how a material bends, yields, and can eventually fail under load. A cantilever beam is fixed firmly at one end and loaded at the other end. When the load stays within the elastic range, the beam returns to its original shape after the load is removed. That reversible behavior is called elasticity. If the load goes beyond the elastic limit, the beam begins plastic deformation. Plastic deformation means the shape change is permanent. In a cantilever beam, this change starts...

unsymmetric loading of thin-walled members

unsymmetric-loading-of-thin-walled-members

Shear Center in Thin-Walled Members

Thin-walled members with non-symmetrical cross-sections are widely used in engineering structures because they save material while still providing strength. Their shape helps with structural integrity, but it also makes load analysis more complex. When these members are loaded in an unsymmetrical way, the stress is not spread evenly. Unsymmetrical loading can make a member bend and twist at the same time. That combined action can lead to deformation or even structural failure. Engineers must...

unsymmetric loading of thin-walled members: problem solving

unsymmetric-loading-of-thin-walled-members-problem-solving

Finding the Shear Center of a Channel Section

Finding the shear center of a channel section starts with the member’s shear force and moments of inertia. A shear center is the point where a load must act so the section bends without twisting. For a channel with uniform thickness, height, and width, the distance to this point can be calculated from the section geometry. The first step is to compute the shear flow at a set distance from the end of the flange. Shear flow is the force per unit length along the wall of the section. It is found...

key terms and concepts

Explore how shearing stress changes across a narrow rectangular beam, including zero stress at the edges and a parabolic distribution toward the center.

Shearing Stress Pattern in a Narrow Beam | JoVE K12

JoVE Core Mechanical Engineering offers concise, easy-to-understand animated videos covering key topics such as equilibrium, forces, truss analysis, and structural mechanics. Explore their real-world applications, and witness these concepts in action through scientist-led experiments.

Shearing Stress Pattern in a Narrow Beam

Description

Transcript