Name: diode reverse current and breakdown
Uploaded: 2024-07-08T13:20:19.000Z
Duration: 1 min 14 s
Channel: JoVE

다이오드는 n형 영역이 공급 전압의 양극 단자에 연결되고 p형 영역이 음극 단자에 연결될 때 역 바이어스됩니다.
더 낮은 역 바이어스 전압에서 다이오드를 통과하는 작은 누설 전류는 주로 소수 캐리어로 인한 것이며 이 영역의 IV 곡선은 거의 평평합니다.
역 바이어스 전압이 항복 전압 또는 무릎 전압으로 알려진 임계값 전압 이상으로 증가함에 따라 전압의 작은 변동에 대해 전류의 가파른 상승이 관찰됩니다.
높은 역전압에서 많이 도핑된 다이오드에서 공핍 영역을 가로지르는 전기장은 원자가 전자가 결합에서 벗어날 수 있을 만큼 충분히 강합니다. 이것은 전자-정공 쌍을 생성하여 전류를 크게 증가시킵니다.
가볍게 도핑된 다이오드에서 높은 역전압은 공핍 영역에서 소수 캐리어를 가속화합니다. 그들은 원자와 충돌하여 추가적인 전자-정공 쌍을 생성합니다. 이 과정은 계단식으로 진행되어 전류가 급격히 증가합니다.
가볍게 도핑된 다이오드에서 전류는 심하게 도핑된 다이오드에 비해 점진적으로 증가합니다.

다이오드: 역바이어스

다이오드는 외부 전압원의 양극 단자가 n형 물질에 연결되고 음극 단자가 p형 물질에 연결될 때 역바이어스됩니다. 이 구성은 다이오드를 통과하는 전류 흐름의 자연스러운 방향과 반대되어 공핍 영역의 폭과 장벽 전위를 효과적으로 증가시킵니다. 역방향 바이어스 조건은 주로 소수 전하 캐리어로 인해 최소한의 누설 전류를 생성합니다. 이러한 누출은 표준 실내 조건에서 역전압이 열 전압을 초과할 때 심각해지며 전류-전압(I-V) 응답 곡선이 평탄해집니다. 순방향 바이어스에서 관찰되는 기하급수적인 전류 증가와 달리 역방향 바이어스의 증가는 무시할 수 있습니다.
그러나 실제로는 다이오드의 역전류가 예상된 포화 전류를 초과하는 경우가 많습니다. 예를 들어, 펨토암페어 수준의 역포화 전류를 갖는 소신호용으로 설계된 다이오드는 나노암페어 수준의 역전류를 나타낼 수 있습니다. 이 역전류는 역전압에 따라 약간 증가하지만 이러한 변화는 I-V 곡선에 눈에 띄게 영향을 미치기에는 너무 작습니다. 이 역전류는 다이오드 접합의 물리적 크기에 따라 접합 내 열 캐리어 생성으로 인해 발생합니다.
인가된 역전압이 각 다이오드에 특정한 항복 전압으로 알려진 임계 임계값에 도달하면 역전류의 급격한 증가가 발생합니다. I-V 곡선의 무릎으로 표시되는 이 현상은 최소한의 전압 증가로 상당한 전류 상승을 의미합니다.
<img alt="Figure 1" src="/files/ftp_upload/15714/15714_Figure_1.svg" style="height: 200px;">
전류가 일반적으로 자료 시트의 최대 전력 소비 용량으로 정의되는 안전한 작동 영역 내에 있는 경우 다이오드 항복이 본질적으로 손상되지 않는다는 점을 인식하는 것이 중요합니다. 잠재적인 손상을 방지하려면 역전류를 안전한 수준으로 제한하도록 설계된 외부 회로가 필요합니다. 전압 조절을 위해 항복 영역 내에서 기능하도록 설계된 제너 다이오드는 이러한 조건에서 안전하게 작동하는 다이오드의 예입니다.

다이오드는 n형 영역이 공급 전압의 양극 단자에 연결되고 p형 영역이 공급 전압의 양극 단자에 연결될 때 역 바이어스됩니다.

Education

교육

JoVE Core

Electrical Engineering

전기공학

Unit 1

제1단원

Diodes

다이오드

KEY TERMS AND CONCEPTS

주요 용어 및 개념

Diode: Reverse bias

diode reverse current and breakdown

A diode in reverse bias blocks current flow and widens its depletion region. In this setup, the positive terminal of the power source connects to the n-type material, and the negative terminal connects to the p-type material. The reverse connection also raises the barrier potential, so current stays very small.

The small reverse current is called leakage current. It comes mainly from minority charge carriers. At room temperature, once the reverse voltage is above the thermal voltage, the diode’s I-V curve becomes nearly flat, unlike the steep rise seen in forward bias.

Real diodes often show more reverse current than the ideal saturation current predicts. Small-signal diodes with femtoampere-level reverse saturation current may still measure nanoampere-level reverse current. This current can rise a little as reverse voltage increases, but the change is usually too small to affect the I-V curve much. It comes from thermal carrier generation in the junction and depends on the junction’s physical size.

A sharp increase in reverse current begins at the breakdown voltage. This is the critical reverse voltage where the I-V curve shows a knee and current rises quickly with little extra voltage. Breakdown is not always damaging if the current stays within the diode’s safe operating area, which is usually tied to the maximum power dissipation listed in the datasheet. External circuitry is used to keep reverse current safe, and Zener diodes are designed to work in the breakdown region for voltage regulation.

Diode Reverse Current and Breakdown

the ideal diode

Ideal Diode I-V Curve and Rectification

An ideal diode is a simple model of a semiconductor diode used to show how current moves through circuits. A diode has two terminals. The anode is positive, and the cathode is negative. In this model, current can flow only in one direction. When a positive voltage is applied to the anode relative to the cathode, the diode is forward-biased. In that state, it conducts current. When the cathode is at a higher potential than the anode, the diode is reverse-biased. It then blocks current and acts...

diode: forward bias

Diode Current in Forward Bias

Diode current in forward bias depends on how the p-type and n-type regions are connected to a battery. When the p-type region is tied to the positive terminal and the n-type region to the negative terminal, the diode is forward-biased. This setup lowers the potential barrier inside the diode and lets current move easily from the p-type side to the n-type side. The current-voltage behavior of a forward-biased diode is described by its I-V characteristics. These characteristics depend on the...

diode: reverse bias

A diode in reverse bias blocks current flow and widens its depletion region. In this setup, the positive terminal of the power source connects to the n-type material, and the negative terminal connects to the p-type material. The reverse connection also raises the barrier potential, so current stays very small. The small reverse current is called leakage current. It comes mainly from minority charge carriers. At room temperature, once the reverse voltage is above the thermal voltage, the...

zener diodes

Zener Diode Voltage Regulation

Zener diodes are semiconductor devices used to hold voltage steady in reverse bias. In reverse breakdown, current flows into the cathode and makes it positive relative to the anode. This behavior is different from a conventional diode and is the reason Zener diodes are useful in voltage regulation. A Zener diode has a nearly vertical current-voltage, or I-V, curve above a threshold called the knee current. That shape lets it keep a fairly stable voltage over a wide range of currents.

modeling of diode forward characteristics

modeling-of-diode-forward-characteristics

Diode Forward Bias: I-V Curve and Models

Diode forward bias is analyzed with the current-voltage, or I-V, curve and two common circuit models. These models help describe how a diode behaves when current flows in the forward direction. They are useful for electronic circuit design and analysis. The exponential diode model is used when the source voltage rises above 0.5 volts. At that point, the diode current increases exponentially above the saturation current. The I-V curve shows this nonlinear response as the forward voltage...

small-signal diode model

Diode Bias and Small-Signal Response

Diode bias and small-signal response describe how a diode behaves when a steady DC voltage and a tiny changing signal act on the same circuit. The DC bias sets the diode’s operating point, or Q point. Around that point, the diode current and voltage follow an exponential I-V relationship. A small time-varying signal can be added on top of the DC bias to study how the diode responds to small changes. When the signal voltage is much smaller than the thermal voltage, the diode’s behavior can be...

modeling of diode reverse characteristics

modeling-of-diode-reverse-characteristics

Zener Diode Load-Line Modeling

Zener diode load-line modeling shows how a reverse-biased diode sets a steady voltage in a circuit. Zener diodes use reverse breakdown in a controlled way, so they can hold a fixed voltage across their terminals. This makes them useful for voltage regulation. When the reverse voltage rises above the Zener voltage, or VZ, the diode enters the breakdown region. In this region, the current-voltage, or I-V, curve becomes nearly vertical after the knee current, IZ, is reached. That means the...

half wave rectifier

Single-Diode AC to DC Conversion

Single-diode AC to DC conversion uses a half-wave rectifier to change alternating current into a unidirectional voltage. The circuit is simple. It uses one diode in series with a load resistor and an AC power source. The diode controls the current because it allows flow in only one direction. During the positive half-cycles of the AC input, the diode is forward-biased. When the input voltage is greater than the diode threshold, current flows and an output voltage appears across the load...

full wave rectifier

AC to DC Conversion with Full-Wave Rectifiers

A full-wave rectifier converts alternating current, or AC, into direct current, or DC. It is more efficient than a half-wave rectifier. The circuit usually uses a center-tapped transformer, two diodes, and a load resistor. The center-tapped transformer is the key part of the circuit. Its secondary winding is split into two equal voltages with opposite polarities. That split lets the rectifier use both halves of the AC input waveform. During the positive half-cycle of the AC signal, diode D1...

bridge rectifier

AC to DC Conversion with Bridge Diodes

A bridge rectifier converts alternating current (AC) into direct current (DC) using four diodes arranged in a bridge layout. It is used to turn both halves of the AC waveform into a single-direction output. That makes it an important part of many electronics circuits. During the positive half-cycle, diodes D1 and D2 conduct. Current then flows through the load resistor R. At the same time, D3 and D4 are reverse-biased, so they do not conduct. The action switches during the negative half-cycle.

clipper circuit

Dual Diode Wave Clipping

Dual diode wave clipping uses diodes and biasing batteries to reshape an AC signal. A clipper circuit is a wave-shaping device that changes waveform parts without changing the whole signal. It is commonly used in television and radar communication systems to improve waveform modulation in transmitters and receivers. A dual-clipper setup uses two ideal diodes, two biasing batteries, and a resistor connected in parallel. The circuit works by responding to the phase of the input AC signal. The...

clamper circuit

DC Restorer for Waveform Level Shifting

A clamper circuit, or DC restorer, shifts a waveform up or down by adding a DC level. It is a special form of rectifier circuit. In this setup, the output is taken across the diode instead of across the capacitor. The circuit works well with square wave inputs and other pulse signals. The diode direction lets the capacitor charge to the most negative peak of the input signal. After that, the diode stops conducting. The capacitor then holds that voltage at a steady value. As a result, the...

voltage doubler circuit

How a Voltage Doubler Raises AC Output

A voltage doubler circuit raises the output voltage by using a clamping section and a rectifier section. The clamping section includes a capacitor, C1, and a diode, D1. The rectifier section includes a second diode, D2, and a capacitor, C2. The circuit starts working when a sinusoidal input signal enters the clamping section. Under ideal conditions, this stage clamps the positive peaks at zero volts. It also lets the negative peak reach a magnitude that is twice the input amplitude. That...

schottky barrier diode

Fast Switching in Schottky Diodes

Schottky barrier diodes use a metal-semiconductor junction to control current flow. They are built by combining a metal layer with a moderately doped n-type semiconductor. This contact creates the Schottky barrier, which gives the diode its one-way current behavior. When the metal touches the semiconductor, charge transfer occurs. The Fermi levels of the two materials align, and a depletion region forms near the contact area. In an n-type semiconductor, this region contains uncompensated...

key terms and concepts

Learn how reverse bias creates leakage current, why the diode I-V curve flattens, and what happens at breakdown voltage, including safe use in Zener diodes.

Diode Reverse Current and Breakdown | JoVE K12

JoVE Core Electrical Engineering offers easy-to-understand animated videos that cover fundamental concepts of electric circuits along with circuit analysis techniques. It incorporates first-order and second-order circuits using operational amplifiers and circuit transformation concepts. The inclusion of practical design examples and real-world applications through scientist-in-action videos adds significant educational value, making complex concepts accessible.

electrical engineering

Diode Reverse Current and Breakdown

Description

Transcript

Tags