Name: ac to dc conversion with bridge diodes
Uploaded: 2025-05-22T09:06:19.000Z
Duration: 1 min 24 s
Channel: JoVE

AC를 DC로 변환하는 데 필수적인 브리지 정류기는 브리지 구성으로 배열된 4개의 다이오드로 구성됩니다.
이 배열을 통해 파형의 양극과 음극 절반을 모두 수정할 수 있습니다.
입력 전압의 양의 반주기 동안 브리지 정류기는 다이오드 D1 및 D2와 저항 R을 통해 전류를 전도하는 반면 다이오드 D3 및 D4는 역 바이어스됩니다.
반대로, 음의 반주기 동안 2차 전압은 음수이고 전류는 다이오드 D3 및 D4와 저항 R을 통해 흐르며 다이오드 D1 및 D2는 역 바이어스됩니다.
변화하는 주기에도 불구하고 전류 흐름의 방향은 일정하게 유지되어 일관되게 양의 맥동 DC 출력 전압을 생성합니다.
피크 역전압은 양의 반주기 동안 결정되며 중앙 탭 변압기가 있는 전파 정류기 값의 약 절반입니다.
브리지 정류기는 변압기의 2차 권선에 더 적은 회전이 필요하므로 더 효율적이고 컴팩트합니다.
브리지 정류기의 효율은 쇼트키 다이오드를 사용하거나 커패시터 필터를 통합하여 손실을 줄이고 DC 출력의 품질을 향상시킴으로써 향상될 수 있습니다.

브리지 정류기

브리지 정류기는 교류(AC)를 직류(DC)로 효율적으로 변환하는 전자 장치에 필수적입니다. 브리지 레이아웃으로 구성된 4개의 다이오드로 구성된 이 정류기는 AC 파형의 양극 및 음극 절반을 모두 효과적으로 처리하므로 전압 조정 및 출력 안정성 측면에서 반파 및 전파 중앙탭 정류기보다 우수합니다.
작동상 브리지 정류기는 AC 입력의 각 반주기 동안 두 개의 다이오드를 통해 전류 흐름을 허용합니다. 특히 양의 반주기 동안 다이오드 D_1과 D_2는 전도되어 전류가 부하 저항기 R을 통과하도록 허용하는 반면 다이오드 D_3과 D_4는 역바이어스되고 비전도성입니다. 이 동작은 다이오드 D_3과 D_4가 전도되고 D_1과 D_2가 역방향 바이어스되는 음의 반주기 동안 역전됩니다. 입력 전압의 교번 특성에도 불구하고 부하 저항기 R을 통과하는 전류는 단일 방향으로 유지되어 안정적인 양의 맥동 DC 출력을 보장합니다.
<img alt="Figure 1" src="/files/ftp_upload/15721/15721_Figure_1.svg" style="height: 180px;">
필요한 피크 역전압(PIV_은 소스 전압(V_S)에서 다이오드 전압(V_D)을 뺀 값으로, 중앙 탭 변압기가 있는 전파 정류기의 약 절반에 해당하는 값을 산출합니다. 따라서 브리지 정류기는 더욱 효율적이며 더욱 컴팩트하고 비용 효율적인 설계가 가능합니다.
<img alt="Equation 1" src="/files/ftp_upload/15721/15721_Equation_1.svg" style="height: 20px;">

<img alt="Equation 2" src="/files/ftp_upload/15721/15721_Equation_2.svg" style="height: 42px;">
또한 브리지 정류기 회로에서 변압기의 2차 권선에는 중앙 탭 변압기 구성보다 적은 권선이 필요하므로 전체 효율이 향상됩니다. 낮은 순방향 전압 강하와 빠른 복구 시간으로 알려진 쇼트키 다이오드를 통합하거나 리플을 최소화하는 커패시터 필터를 추가하여 고품질 D_C 출력을 생성함으로써 브리지 정류기의 성능을 크게 향상시킬 수도 있습니다.

AC를 DC로 변환하는 데 필수적인 브리지 정류기는 브리지 구성으로 배열된 4개의 다이오드로 구성됩니다.
이 배열을 통해 수정할 수 있습니다 ...

Education

교육

JoVE Core

Electrical Engineering

전기공학

Unit 1

제1단원

Diodes

다이오드

KEY TERMS AND CONCEPTS

주요 용어 및 개념

Bridge rectifier

ac to dc conversion with bridge diodes

A bridge rectifier converts alternating current (AC) into direct current (DC) using four diodes arranged in a bridge layout. It is used to turn both halves of the AC waveform into a single-direction output. That makes it an important part of many electronics circuits.

During the positive half-cycle, diodes D1 and D2 conduct. Current then flows through the load resistor R. At the same time, D3 and D4 are reverse-biased, so they do not conduct.

The action switches during the negative half-cycle. Diodes D3 and D4 conduct, while D1 and D2 are reverse-biased. Even though the input keeps alternating, the current through the load resistor still moves in one direction. The output is a steady positive pulsating DC signal.

A bridge rectifier can offer better voltage regulation and output stability than a half-wave rectifier or a full-wave center-tapped rectifier. It also needs a peak inverse voltage (PIV) of about V D subtracted from V S, which is roughly half the PIV needed in a center-tapped full-wave rectifier. This helps make the design more compact and cost-effective.

The transformer secondary in a bridge rectifier circuit also needs fewer turns than a center-tapped transformer setup. Performance can improve further with Schottky diodes, which have a low forward voltage drop and fast recovery time. A capacitor filter can also reduce ripple and produce higher-quality DC output.

AC to DC Conversion with Bridge Diodes

the ideal diode

Ideal Diode I-V Curve and Rectification

An ideal diode is a simple model of a semiconductor diode used to show how current moves through circuits. A diode has two terminals. The anode is positive, and the cathode is negative. In this model, current can flow only in one direction. When a positive voltage is applied to the anode relative to the cathode, the diode is forward-biased. In that state, it conducts current. When the cathode is at a higher potential than the anode, the diode is reverse-biased. It then blocks current and acts...

diode: forward bias

Diode Current in Forward Bias

Diode current in forward bias depends on how the p-type and n-type regions are connected to a battery. When the p-type region is tied to the positive terminal and the n-type region to the negative terminal, the diode is forward-biased. This setup lowers the potential barrier inside the diode and lets current move easily from the p-type side to the n-type side. The current-voltage behavior of a forward-biased diode is described by its I-V characteristics. These characteristics depend on the...

diode: reverse bias

Diode Reverse Current and Breakdown

A diode in reverse bias blocks current flow and widens its depletion region. In this setup, the positive terminal of the power source connects to the n-type material, and the negative terminal connects to the p-type material. The reverse connection also raises the barrier potential, so current stays very small. The small reverse current is called leakage current. It comes mainly from minority charge carriers. At room temperature, once the reverse voltage is above the thermal voltage, the...

zener diodes

Zener Diode Voltage Regulation

Zener diodes are semiconductor devices used to hold voltage steady in reverse bias. In reverse breakdown, current flows into the cathode and makes it positive relative to the anode. This behavior is different from a conventional diode and is the reason Zener diodes are useful in voltage regulation. A Zener diode has a nearly vertical current-voltage, or I-V, curve above a threshold called the knee current. That shape lets it keep a fairly stable voltage over a wide range of currents.

modeling of diode forward characteristics

modeling-of-diode-forward-characteristics

Diode Forward Bias: I-V Curve and Models

Diode forward bias is analyzed with the current-voltage, or I-V, curve and two common circuit models. These models help describe how a diode behaves when current flows in the forward direction. They are useful for electronic circuit design and analysis. The exponential diode model is used when the source voltage rises above 0.5 volts. At that point, the diode current increases exponentially above the saturation current. The I-V curve shows this nonlinear response as the forward voltage...

small-signal diode model

Diode Bias and Small-Signal Response

Diode bias and small-signal response describe how a diode behaves when a steady DC voltage and a tiny changing signal act on the same circuit. The DC bias sets the diode’s operating point, or Q point. Around that point, the diode current and voltage follow an exponential I-V relationship. A small time-varying signal can be added on top of the DC bias to study how the diode responds to small changes. When the signal voltage is much smaller than the thermal voltage, the diode’s behavior can be...

modeling of diode reverse characteristics

modeling-of-diode-reverse-characteristics

Zener Diode Load-Line Modeling

Zener diode load-line modeling shows how a reverse-biased diode sets a steady voltage in a circuit. Zener diodes use reverse breakdown in a controlled way, so they can hold a fixed voltage across their terminals. This makes them useful for voltage regulation. When the reverse voltage rises above the Zener voltage, or VZ, the diode enters the breakdown region. In this region, the current-voltage, or I-V, curve becomes nearly vertical after the knee current, IZ, is reached. That means the...

half wave rectifier

Single-Diode AC to DC Conversion

Single-diode AC to DC conversion uses a half-wave rectifier to change alternating current into a unidirectional voltage. The circuit is simple. It uses one diode in series with a load resistor and an AC power source. The diode controls the current because it allows flow in only one direction. During the positive half-cycles of the AC input, the diode is forward-biased. When the input voltage is greater than the diode threshold, current flows and an output voltage appears across the load...

full wave rectifier

AC to DC Conversion with Full-Wave Rectifiers

A full-wave rectifier converts alternating current, or AC, into direct current, or DC. It is more efficient than a half-wave rectifier. The circuit usually uses a center-tapped transformer, two diodes, and a load resistor. The center-tapped transformer is the key part of the circuit. Its secondary winding is split into two equal voltages with opposite polarities. That split lets the rectifier use both halves of the AC input waveform. During the positive half-cycle of the AC signal, diode D1...

bridge rectifier

A bridge rectifier converts alternating current (AC) into direct current (DC) using four diodes arranged in a bridge layout. It is used to turn both halves of the AC waveform into a single-direction output. That makes it an important part of many electronics circuits. During the positive half-cycle, diodes D1 and D2 conduct. Current then flows through the load resistor R. At the same time, D3 and D4 are reverse-biased, so they do not conduct. The action switches during the negative half-cycle.

clipper circuit

Dual Diode Wave Clipping

Dual diode wave clipping uses diodes and biasing batteries to reshape an AC signal. A clipper circuit is a wave-shaping device that changes waveform parts without changing the whole signal. It is commonly used in television and radar communication systems to improve waveform modulation in transmitters and receivers. A dual-clipper setup uses two ideal diodes, two biasing batteries, and a resistor connected in parallel. The circuit works by responding to the phase of the input AC signal. The...

clamper circuit

DC Restorer for Waveform Level Shifting

A clamper circuit, or DC restorer, shifts a waveform up or down by adding a DC level. It is a special form of rectifier circuit. In this setup, the output is taken across the diode instead of across the capacitor. The circuit works well with square wave inputs and other pulse signals. The diode direction lets the capacitor charge to the most negative peak of the input signal. After that, the diode stops conducting. The capacitor then holds that voltage at a steady value. As a result, the...

voltage doubler circuit

How a Voltage Doubler Raises AC Output

A voltage doubler circuit raises the output voltage by using a clamping section and a rectifier section. The clamping section includes a capacitor, C1, and a diode, D1. The rectifier section includes a second diode, D2, and a capacitor, C2. The circuit starts working when a sinusoidal input signal enters the clamping section. Under ideal conditions, this stage clamps the positive peaks at zero volts. It also lets the negative peak reach a magnitude that is twice the input amplitude. That...

schottky barrier diode

Fast Switching in Schottky Diodes

Schottky barrier diodes use a metal-semiconductor junction to control current flow. They are built by combining a metal layer with a moderately doped n-type semiconductor. This contact creates the Schottky barrier, which gives the diode its one-way current behavior. When the metal touches the semiconductor, charge transfer occurs. The Fermi levels of the two materials align, and a depletion region forms near the contact area. In an n-type semiconductor, this region contains uncompensated...

key terms and concepts

Learn how four diodes in a bridge layout convert AC to DC, why the output stays one direction, and how filtering improves the pulsating signal.

AC to DC Conversion with Bridge Diodes | JoVE K12

JoVE Core Electrical Engineering offers easy-to-understand animated videos that cover fundamental concepts of electric circuits along with circuit analysis techniques. It incorporates first-order and second-order circuits using operational amplifiers and circuit transformation concepts. The inclusion of practical design examples and real-world applications through scientist-in-action videos adds significant educational value, making complex concepts accessible.

electrical engineering

AC to DC Conversion with Bridge Diodes

Description

Transcript

Tags