Name: how a voltage doubler raises ac output
Uploaded: 2025-05-22T09:06:19.000Z
Duration: 1 min 23 s
Channel: JoVE

두 개의 연속된 섹션, 즉 클램핑 섹션과 정류기 섹션으로 구성된 전압 더블러 회로를 고려하십시오.
클램핑 섹션은 커패시터 C1과 다이오드 D1로 구성되고, 정류부 섹션은 다이오드 D 2와 커패시터 C2로 구성됩니다.
특정 진폭의 정현파 입력이 클램핑 섹션에 적용되면 이상적인 다이오드 동작을 가정하여 다이오드 전체에 출력 전압 파형을 생성합니다.
포지티브 피크를 0볼트로 고정하는 동시에 음의 피크가 정현파 입력 진폭의 두 배 값에 도달하도록 합니다.
클램핑 섹션의 출력 파형은 정류기 섹션에 대한 입력 역할을 합니다.
커패시터 C2 양단에 DC 전압을 생성하며, 이는 정현파 입력 진폭의 두 배에 해당합니다.
출력 전압이 입력 전압의 피크 값의 두 배이기 때문에 이 회로를 전압 더블러라고 합니다.
이 기술은 입력 정현파 진폭의 더 높은 배수를 가진 출력 전압을 생성하도록 확장할 수 있습니다.
전압 더블러는 과학 장비, 신호 처리 및 전자 장치의 DC-DC 변환기를 포함한 다양한 응용 분야에 사용됩니다.

전압 배전압 회로

Voltage Doubler Circuit

전압 배전압 회로는 클램핑 섹션과 정류기 섹션이라는 두 가지 주요 구성 요소를 통합합니다. 클램핑부는 커패시터(C_1)와 다이오드(D_1)로 구성되며, 정류부는 또 다른 다이오드(D_2)와 커패시터(C_2)로 구성됩니다. 이 회로는 정현파 입력 전압의 두 배 진폭을 갖는 출력 전압을 생성합니다.
<img alt="Figure 1" src="/files/ftp_upload/15724/15724_Figure_1v2.svg" style="height: 132px;">
클램핑 섹션에 정현파 입력이 도입되면 회로가 작동하기 시작합니다. 이상적인 조건에서 이 섹션은 다이오드 D_1에 걸쳐 전압 파형을 출력하여 0V에서 양의 피크를 효과적으로 클램핑하고 음의 피크가 정현파 입력 진폭의 두 배에 달하는 크기를 달성하도록 허용합니다. 클램핑 섹션에서 변환된 이 파형은 정류기 섹션으로 공급됩니다. 여기서 놀라운 변환이 발생하여 커패시터 C_2에 DC 전압이 생성됩니다. 이 전압은 초기 정현파 입력 진폭의 두 배를 미러링하여 회로에 이름을 부여하고 주요 기능을 표시하는 배가 효과를 제공합니다.
전압 배전압의 기본 원리는 배전압에만 국한되지 않고 입력 전압에 더 높은 요소를 곱하도록 적용하여 적용 범위를 넓힐 수도 있습니다. 전압 배전압은 다양한 분야에서 중추적인 역할을 하며 과학 기기에서의 용도를 찾고, 신호 처리 기술을 향상시키며, 수많은 전자 장치 내 DC-DC 변환기의 필수 구성 요소 역할을 합니다. 전압을 효율적으로 두 배로 늘리는 이러한 기능은 전압 배전압 회로를 전자 설계 및 응용 분야의 초석으로 만듭니다.

두 개의 연속된 섹션, 즉 클램핑 섹션과 정류기 섹션으로 구성된 전압 더블러 회로를 고려하십시오.
클램핑 섹션은 ...

Education

교육

JoVE Core

Electrical Engineering

전기공학

Unit 1

제1단원

Diodes

다이오드

KEY TERMS AND CONCEPTS

주요 용어 및 개념

how a voltage doubler raises ac output

A voltage doubler circuit raises the output voltage by using a clamping section and a rectifier section. The clamping section includes a capacitor, C1, and a diode, D1. The rectifier section includes a second diode, D2, and a capacitor, C2.

The circuit starts working when a sinusoidal input signal enters the clamping section. Under ideal conditions, this stage clamps the positive peaks at zero volts. It also lets the negative peak reach a magnitude that is twice the input amplitude.

That shaped waveform then moves into the rectifier section. There, the circuit produces a DC voltage across capacitor C2. This output equals twice the amplitude of the original sinusoidal input, which gives the circuit its voltage-doubling effect.

The same principle can also be extended to multiply the input voltage by higher factors. Because of this, voltage doublers are useful in scientific instruments, signal processing, and DC-DC converters found in many electronic devices. This makes the circuit an important part of electronic design and application.

How a Voltage Doubler Raises AC Output

the ideal diode

Ideal Diode I-V Curve and Rectification

An ideal diode is a simple model of a semiconductor diode used to show how current moves through circuits. A diode has two terminals. The anode is positive, and the cathode is negative. In this model, current can flow only in one direction. When a positive voltage is applied to the anode relative to the cathode, the diode is forward-biased. In that state, it conducts current. When the cathode is at a higher potential than the anode, the diode is reverse-biased. It then blocks current and acts...

diode: forward bias

Diode Current in Forward Bias

Diode current in forward bias depends on how the p-type and n-type regions are connected to a battery. When the p-type region is tied to the positive terminal and the n-type region to the negative terminal, the diode is forward-biased. This setup lowers the potential barrier inside the diode and lets current move easily from the p-type side to the n-type side. The current-voltage behavior of a forward-biased diode is described by its I-V characteristics. These characteristics depend on the...

diode: reverse bias

Diode Reverse Current and Breakdown

A diode in reverse bias blocks current flow and widens its depletion region. In this setup, the positive terminal of the power source connects to the n-type material, and the negative terminal connects to the p-type material. The reverse connection also raises the barrier potential, so current stays very small. The small reverse current is called leakage current. It comes mainly from minority charge carriers. At room temperature, once the reverse voltage is above the thermal voltage, the...

zener diodes

Zener Diode Voltage Regulation

Zener diodes are semiconductor devices used to hold voltage steady in reverse bias. In reverse breakdown, current flows into the cathode and makes it positive relative to the anode. This behavior is different from a conventional diode and is the reason Zener diodes are useful in voltage regulation. A Zener diode has a nearly vertical current-voltage, or I-V, curve above a threshold called the knee current. That shape lets it keep a fairly stable voltage over a wide range of currents.

modeling of diode forward characteristics

modeling-of-diode-forward-characteristics

Diode Forward Bias: I-V Curve and Models

Diode forward bias is analyzed with the current-voltage, or I-V, curve and two common circuit models. These models help describe how a diode behaves when current flows in the forward direction. They are useful for electronic circuit design and analysis. The exponential diode model is used when the source voltage rises above 0.5 volts. At that point, the diode current increases exponentially above the saturation current. The I-V curve shows this nonlinear response as the forward voltage...

small-signal diode model

Diode Bias and Small-Signal Response

Diode bias and small-signal response describe how a diode behaves when a steady DC voltage and a tiny changing signal act on the same circuit. The DC bias sets the diode’s operating point, or Q point. Around that point, the diode current and voltage follow an exponential I-V relationship. A small time-varying signal can be added on top of the DC bias to study how the diode responds to small changes. When the signal voltage is much smaller than the thermal voltage, the diode’s behavior can be...

modeling of diode reverse characteristics

modeling-of-diode-reverse-characteristics

Zener Diode Load-Line Modeling

Zener diode load-line modeling shows how a reverse-biased diode sets a steady voltage in a circuit. Zener diodes use reverse breakdown in a controlled way, so they can hold a fixed voltage across their terminals. This makes them useful for voltage regulation. When the reverse voltage rises above the Zener voltage, or VZ, the diode enters the breakdown region. In this region, the current-voltage, or I-V, curve becomes nearly vertical after the knee current, IZ, is reached. That means the...

half wave rectifier

Single-Diode AC to DC Conversion

Single-diode AC to DC conversion uses a half-wave rectifier to change alternating current into a unidirectional voltage. The circuit is simple. It uses one diode in series with a load resistor and an AC power source. The diode controls the current because it allows flow in only one direction. During the positive half-cycles of the AC input, the diode is forward-biased. When the input voltage is greater than the diode threshold, current flows and an output voltage appears across the load...

full wave rectifier

AC to DC Conversion with Full-Wave Rectifiers

A full-wave rectifier converts alternating current, or AC, into direct current, or DC. It is more efficient than a half-wave rectifier. The circuit usually uses a center-tapped transformer, two diodes, and a load resistor. The center-tapped transformer is the key part of the circuit. Its secondary winding is split into two equal voltages with opposite polarities. That split lets the rectifier use both halves of the AC input waveform. During the positive half-cycle of the AC signal, diode D1...

bridge rectifier

AC to DC Conversion with Bridge Diodes

A bridge rectifier converts alternating current (AC) into direct current (DC) using four diodes arranged in a bridge layout. It is used to turn both halves of the AC waveform into a single-direction output. That makes it an important part of many electronics circuits. During the positive half-cycle, diodes D1 and D2 conduct. Current then flows through the load resistor R. At the same time, D3 and D4 are reverse-biased, so they do not conduct. The action switches during the negative half-cycle.

clipper circuit

Dual Diode Wave Clipping

Dual diode wave clipping uses diodes and biasing batteries to reshape an AC signal. A clipper circuit is a wave-shaping device that changes waveform parts without changing the whole signal. It is commonly used in television and radar communication systems to improve waveform modulation in transmitters and receivers. A dual-clipper setup uses two ideal diodes, two biasing batteries, and a resistor connected in parallel. The circuit works by responding to the phase of the input AC signal. The...

clamper circuit

DC Restorer for Waveform Level Shifting

A clamper circuit, or DC restorer, shifts a waveform up or down by adding a DC level. It is a special form of rectifier circuit. In this setup, the output is taken across the diode instead of across the capacitor. The circuit works well with square wave inputs and other pulse signals. The diode direction lets the capacitor charge to the most negative peak of the input signal. After that, the diode stops conducting. The capacitor then holds that voltage at a steady value. As a result, the...

voltage doubler circuit

A voltage doubler circuit raises the output voltage by using a clamping section and a rectifier section. The clamping section includes a capacitor, C1, and a diode, D1. The rectifier section includes a second diode, D2, and a capacitor, C2. The circuit starts working when a sinusoidal input signal enters the clamping section. Under ideal conditions, this stage clamps the positive peaks at zero volts. It also lets the negative peak reach a magnitude that is twice the input amplitude. That...

schottky barrier diode

Fast Switching in Schottky Diodes

Schottky barrier diodes use a metal-semiconductor junction to control current flow. They are built by combining a metal layer with a moderately doped n-type semiconductor. This contact creates the Schottky barrier, which gives the diode its one-way current behavior. When the metal touches the semiconductor, charge transfer occurs. The Fermi levels of the two materials align, and a depletion region forms near the contact area. In an n-type semiconductor, this region contains uncompensated...

key terms and concepts

Learn how a clamping section and rectifier section work together in a voltage doubler circuit to produce a DC output with twice the input amplitude.

How a Voltage Doubler Raises AC Output | JoVE K12

JoVE Core Electrical Engineering offers easy-to-understand animated videos that cover fundamental concepts of electric circuits along with circuit analysis techniques. It incorporates first-order and second-order circuits using operational amplifiers and circuit transformation concepts. The inclusion of practical design examples and real-world applications through scientist-in-action videos adds significant educational value, making complex concepts accessible.

electrical engineering

How a Voltage Doubler Raises AC Output

Description

Transcript

Tags