Name: protecting mortar during weather changes
Uploaded: 2024-09-12T16:16:29.000Z
Duration: 1 min 21 s
Channel: JoVE

추운 날씨에는 모르타르 준비에 급속 경화 시멘트가 사용됩니다. 뜨거운 물을 첨가하여 모르타르 온도를 화씨 40도에서 120도 사이로 유지합니다.
온도가 화씨 32도 미만인 경우 석조 장치 및 시멘트 백은 높은 플랫폼에 보관하고 방수 시트로 덮고 공간 히터를 사용하여 가열합니다.
모래가 얼어붙는 것은 전기 담요나 히트 파이프를 사용하여 가열하여 방지합니다.
또한 풍속이 시속 15마일 이상인 경우 작업 현장에 바람막이가 제공됩니다.
작업이 끝나면 석조 벽은 동결을 방지하기 위해 24 시간 동안 단열 담요로 덮입니다.
더운 날씨에는 석조 장치, 모래, 시멘트 백 및 모르타르 장비가 직사광선으로부터 보호됩니다.
모르타르 장비를 물로 씻어내고, 모르타르 혼합물에 시원한 물을 추가하고, 석조 장치를 놓기 전에 미리 적시는 것은 더운 날씨의 석조물을 위해 연습됩니다.
작업이 끝나면 안개 스프레이를 석조물에 바르고 내후성 멤브레인으로 덮어 태양으로부터 보호합니다.

추운 날씨와 더운 날씨의 석조

추운 날씨에 석조 공사는 모르타르가 경화되기 전에 얼지 않도록 특정 예방 조치가 필요합니다. 얼면 강도와 방수성이 크게 약화될 수 있기 때문입니다. 모르타르 온도는 적절한 수화 및 경화를 위해 15.56°C에서 26.67°C 사이로 유지해야 합니다. 4.44°C 미만에서는 모르타르 물을 가열해야 하지만 48.89°C를 초과해서는 안 됩니다. 고온은 모르타르의 압축 및 결합 강도를 감소시킬 수 있기 때문입니다.

다른 주요 관행으로는 석조 유닛과 모래를 건조하고 동결 온도로부터 보호하고, 가열된 모래를 사용하여 모르타르를 최적의 온도로 유지하고, 더 빠른 경화를 위해 III형 시멘트를 사용하는 것이 있습니다. 모르타르는 냉각을 방지하기 위해 소량으로 혼합해야 하며, 석공의 작업장은 바람으로부터 보호하되 필요한 경우 가열해야 합니다. 새로 놓인 석조는 적어도 하루 동안 얼지 않도록 보호해야 하며, 비와 눈으로부터 보호하기 위해 표면을 덮어야 합니다.

더운 날씨에는 모르타르가 너무 빨리 마르지 않도록 하는 것이 과제입니다. 석조 유닛은 모르타르에서 과도한 물 흡수를 방지하기 위해 사용 전에 적셔야 할 수 있습니다. 석조 유닛, 모르타르 재료 및 작업 공간을 그늘에 두면 이를 관리하는 데 도움이 됩니다. 종종 석조는 안개 스프레이로 처리한 다음 날씨에 강한 멤브레인으로 덮어 일과가 끝나면 햇빛으로부터 보호합니다.

추운 날씨에는 모르타르 준비에 급속 경화 시멘트가 사용됩니다. 뜨거운 물을 첨가하여 모르타르 온도를 40도에서 ...

masonry-in-cold-and-hot-weather-conditions

Education

교육

JoVE Core

Civil Engineering

토목공학

Unit 1

제1단원

Masonry

석공사

KEY TERMS AND CONCEPTS

주요 용어 및 개념

Masonry in Cold and Hot Weather Conditions

protecting mortar during weather changes

Masonry work changes in cold and hot weather because mortar must stay at the right temperature and moisture level. If mortar freezes before it cures, its strength and watertightness can drop. For proper hydration and curing, mortar should stay between 60°F and 80°F.

When the weather is below 40°F, the water used for mortar must be heated. The water should not exceed 120°F, because very hot water can reduce compressive strength and bond strength. Masonry units and sand should also stay dry and protected from freezing. Heated sand can help keep the mortar near the best temperature.

Cold-weather work also calls for Type III cement, which cures faster. Masons should mix mortar in small batches so it does not cool too much before use. Workstations should be shielded from wind and heated when needed. Newly laid masonry must be protected from freezing for at least one day. Surfaces should also be covered to block rain and snow.

Hot weather creates the opposite problem, because mortar can dry too fast. Masonry units may need to be dampened before use so they do not pull too much water from the mortar. Keeping the units, mortar ingredients, and work area in the shade also helps. At the end of the day, masonry is often given a fog spray and then covered with weather-resistant membranes to protect it from sunlight.

Protecting Mortar During Weather Changes

composite masonry walls

Bonding and Materials in Composite Masonry

Composite masonry walls use two or more wythes, or vertical layers, of masonry to form one unified wall. The wythes may use the same material or different masonry materials. They are joined to work together as a single structure. These wythes can be bonded in several ways. Builders may use mortar-filled collar joints, grouted spaces, or rigid metal ties with reinforcement. Masonry header units can also connect the layers, but this method is rare. Metal ties are often preferred because they...

masonry cavity walls

Masonry Cavity Walls and Moisture Control

Masonry cavity walls use two wythes, or layers, with a hollow space between them. The outer and inner wythes are linked only by corrosion-resistant metal ties. This design helps manage water and improve wall performance. When rainwater passes through the outer wythe, it moves down through the cavity. Flashing catches the water and directs it toward weep holes, where it can leave the wall. The inner wythe often has damp-proofing on the cavity side. This layer also works as an air barrier. The...

masonry loadbearing walls

How Masonry Walls Support Buildings

Masonry load-bearing walls support floors and roofs and carry those loads down to the foundation. They are built from brick, stone, or concrete masonry units. These walls rely on compressive strength, which means they can resist pushes from above very well. Masonry walls may be reinforced or unreinforced, depending on the building needs. They carry dead loads and live loads while using working stresses that stay below the materials' ultimate strength. That safety margin helps the structure...

masonry curtain walls

Masonry Curtain Walls and Support Systems

Masonry curtain walls use brick or stone veneer as an exterior cladding system. The veneer is supported by the building structure, so the wall can be both attractive and functional. Two main construction methods are used for these walls. One method builds the masonry units in place through traditional layering. The other uses prefabricated panels that are assembled on the ground and then lifted into position. In traditional construction, steel shelf angles attached to the spandrel beam carry...

posttensioned masonry walls

How Masonry Walls Gain Extra Strength

Post-tensioned masonry walls gain extra strength from high-strength steel rods or flexible tendons. These tensioning elements are anchored to the foundation and run vertically through the wall. In some walls, they sit inside the cores of the masonry units. In others, they are placed between the masonry wythes, or layers. The wall is built first with the tensioning elements already in place. After the mortar cures fully, the wall is tightened. Steel rods are tensioned by turning nuts against...

cavity drainage and flashings in masonry walls

cavity-drainage-and-flashings-in-masonry-walls

Moisture Control in Masonry Cavity Walls

Masonry cavity walls use a gap between two wythes, or wall layers, to help control moisture. The cavity is usually at least 2 inches wide, and it may contain insulation. Even with insulation, a clear space of at least 1 inch is kept so water can drain away. Some walls also use a continuous drainage mat to reduce the needed space while still moving moisture out. Weep holes are another key part of cavity drainage. These openings sit at the base of the cavity and let collected water escape. They...

thermal insulation in masonry walls

Masonry Wall Insulation Options

Masonry wall insulation can be placed on the outside, inside the wall, or on the interior surface. The best choice depends on the climate, the building design, and whether the wall is being built new or retrofitted. In hot, dry climates, masonry can help smooth indoor temperatures by absorbing heat during the day and releasing it at night. In many other climates, extra insulation is needed to improve thermal resistance. One common exterior method is an Exterior Insulation and Finish System, or...

expansion and contraction in masonry walls

expansion-and-contraction-in-masonry-walls

Masonry Wall Joints for Temperature and Moisture

Masonry walls change size slightly as temperature and moisture change. Builders account for this movement so the wall does not crack or shift out of place. Thermal movement is usually easy to measure and plan for. Moisture movement is harder to predict. New clay masonry units often absorb water and expand over time in normal outdoor conditions. New concrete masonry units behave differently. They usually shrink as they lose extra moisture gained during production. These opposite changes make...

movement joints in buildings

How Buildings Handle Structural Movement

Buildings are designed to handle movement from temperature changes, moisture changes, and structural deflection. If these changes are ignored, they can cause visible damage or even unsafe conditions. Movement joints give building materials room to move without creating distress. Working joints are the simplest type. They are placed during construction and help materials cope with change as the building goes up. Shingled roofs and wood bevel siding are common examples because they can move with...

types of building separation joints

Building Joints for Movement and Stability

Building separation joints help large or complex buildings move in a controlled way. They split a structure into smaller, separate units. This reduces stress when the building shifts under different forces. The joints are grouped into three main types: volume-change joints, settlement joints, and seismic separation joints. Volume-change joints handle expansion and contraction caused by temperature changes and moisture changes. They are placed where the building mass has discontinuities,...

efflorescence in masonry

Stopping White Salt Crystals on Masonry

Efflorescence is the white, fluffy crystal layer that can form on masonry walls. It happens when water-soluble salts in brick, stone, concrete, or mortar are dissolved by water and carried to the surface. When the water evaporates, the salts are left behind as a powdery deposit. New efflorescence is often seen soon after construction. In many cases, it can be cleaned with water and a brush. It may also fade over time as rain leaches salts out of the masonry surface. If efflorescence appears...

mortar joint deterioration in masonry

Repairing Damaged Mortar Joints in Masonry

Mortar joints in masonry can break down when water collects in them and freezes. The repeated freezing and thawing makes the water expand and shrink. That process creates cracks in the joints and can spread damage over time. As the mortar worsens, pieces may spall, or break off from the joint surface. Loose masonry units can follow, and the wall becomes weaker. Damaged joints also let moisture move into the wall, which adds to the problem. Good construction helps protect mortar joints. Using...

masonry in cold and hot weather conditions

Masonry work changes in cold and hot weather because mortar must stay at the right temperature and moisture level. If mortar freezes before it cures, its strength and watertightness can drop. For proper hydration and curing, mortar should stay between 60°F and 80°F. When the weather is below 40°F, the water used for mortar must be heated. The water should not exceed 120°F, because very hot water can reduce compressive strength and bond strength. Masonry units and sand should also stay dry and...

masonry paving

Masonry Paving Materials and Base Layers

Masonry paving uses bricks, stones, and concrete masonry units to create durable walking and driving surfaces. These materials are selected for their shape, color, strength, and resistance to abrasion and weathering. Masonry units can be used in different paving setups depending on the site and the load they must carry. Some paving systems are installed dry on a thin sand layer over a gravel base. Others are set in mortar or asphalt on a concrete slab. For areas with heavy vehicular loads, a...

key terms and concepts

Learn how cold and hot weather affect masonry mortar, from heating materials and using Type III cement to shading, dampening, and fog spraying.

Protecting Mortar During Weather Changes | JoVE K12

JoVE Core Civil Engineering offers a foundational exploration of essential construction materials such as bricks, stones, steel, wood, and concrete, along with fluid mechanics topics like flow over immersed bodies, open channel flow, and dimensional modeling. It also covers key surveying concepts, including leveling, traverse adjustments, curve design, topographic mapping, and geospatial technologies (GPS & GIS). Science-in-action videos showcase laboratory research on materials, fluids, and surveying practices in real-world engineering systems.

civil engineering

Protecting Mortar During Weather Changes

Description

Transcript

Tags