Name: synchronous machine fault current decay
Uploaded: 2024-11-21T14:54:30.000Z
Duration: 1 min 21 s
Channel: JoVE

A three-phase short circuit test on an unloaded synchronous machine is conducted to study its impact.
The AC fault current&#39;s oscillogram with its DC offset removed, corresponding to one phase of an unloaded synchronous machine, shows a decreasing waveform amplitude from an initial high to a steady-state value.
This is attributed to the magnetic flux caused by short-circuit armature currents, shifting from high-reluctance paths to lower ones, increasing armature inductance. This can be modeled with a time-varying series R-L circuit.
Standard machine theory provides specific reactances used to calculate the instantaneous AC fault current comprising the RMS line-to-neutral prefault terminal voltage.
The RMS sub-transient fault current is determined at time equals zero by the direct axis short-circuit sub-transient time constant, and as time progresses, the RMS AC fault current nears its steady-state value.
Each phase has a different DC offset, peaking when alpha equals zero.
Machine reactances and time constants, provided by manufacturers or obtained from tests, assist in predicting power system behavior during faults, enabling damage control and system stability.

driefasen kortsluiting - onbelaste synchrone machine

Three-Phase Short Circuit&#8212;Unloaded Synchronous Machine

Het uitvoeren van een driefasen kortsluittest op een onbelaste synchrone machine helpt bij het begrijpen van de impact op het systeem. Het oscillogram van de AC-foutstroom, met de DC-offset verwijderd, laat zien dat de amplitude van de golfvorm afneemt van een aanvankelijk hoge waarde naar een steady-state niveau voor één fase van de machine.

Dit gedrag treedt op vanwege de magnetische flux die wordt geproduceerd door de kortsluitankerstromen. Aanvankelijk volgen deze stromen paden met hoge reluctantie, maar verschuiven uiteindelijk naar paden met lagere reluctantie, waardoor de ankerinductantie toeneemt. Deze dynamiek kan worden weergegeven door een tijdsvariërend serieweerstand-inductor (R-L)-circuit.

Volgens de standaard machinetheorie worden specifieke reactanties, zoals sub-transient, transient en steady-state reactanties, gebruikt om de instantane AC-foutstroom te berekenen. Deze berekening is gebaseerd op de RMS lijn-naar-neutraal prefault terminalspanning. De RMS sub-transient foutstroom op het moment van de fout wordt bepaald door de directe as kortsluiting sub-transient reactantie en de bijbehorende tijdconstante. Na verloop van tijd stabiliseert de RMS AC-foutstroom tot zijn steady-state waarde.

Elke fase van de machine ervaart een andere DC-offset, waarbij de piekoffset optreedt wanneer de initiële stroomhoek nul is. De reactanties en tijdconstanten van de machine, geleverd door fabrikanten of afgeleid van tests, zijn cruciaal voor het voorspellen van het gedrag van de machine tijdens storingen. Deze informatie helpt bij het beheren van potentiële schade en het handhaven van de stabiliteit van het systeem tijdens storingen.

Het begrijpen van deze kenmerken is essentieel voor het ontwerpen van robuuste energiesystemen. De gegevens die uit deze tests worden verkregen, stellen ingenieurs in staat te voorspellen hoe het systeem zich zal gedragen onder storingsomstandigheden, wat de ontwikkeling van strategieën om schade te beheersen en de stabiliteit van het systeem te waarborgen, vergemakkelijkt. Deze aanpak zorgt ervoor dat energiesystemen storingen kunnen weerstaan ​​en betrouwbaar blijven werken, waardoor de integriteit en veiligheid van elektrische netwerken behouden blijft.

Driefasen kortsluiting - Onbelaste synchrone machine

A three-phase short circuit test on an unloaded synchronous machine is conducted to study its impact.
The AC fault current&#39;s oscillogram with its DC ...

three-phase-short-circuitunloaded-synchronous-machine

Education

JoVE Core

Electrical Engineering

Elektrotechniek

Unit 1

Symmetrical and Unsymmetrical Faults

Symmetrische en asymmetrische fouten

KEY TERMS AND CONCEPTS

BELANGRIJKE TERMEN EN CONCEPTEN

synchronous machine fault current decay

A three-phase short circuit on an unloaded synchronous machine shows how fault current changes over time. The AC fault current, with the DC offset removed, starts at a high value and then falls to a steady-state level in one phase of the machine.

This change happens because of the magnetic flux created by the short-circuit armature currents. At first, these currents flow through high-reluctance paths. They later shift to lower-reluctance paths, which increases the armature inductance. This behavior can be modeled as a time-varying series resistor-inductor, or R-L, circuit.

Standard machine theory uses sub-transient, transient, and steady-state reactances to calculate the instantaneous AC fault current. The calculation starts from the RMS line-to-neutral prefault terminal voltage. The RMS sub-transient fault current at the moment of the fault depends on the direct axis short-circuit sub-transient reactance and its time constant. As time passes, the RMS AC fault current settles to its steady-state value.

Each phase also has a different DC offset. The peak offset occurs when the initial current angle is zero. The reactances and time constants, which may come from the manufacturer or from tests, help predict machine behavior during faults. This information supports damage control and system stability, which are important for designing strong power systems and keeping electrical networks reliable and safe.

Synchronous Machine Fault Current Decay

series r&#8212;l circuit transients

Fault Current in a Series R-L Circuit

A series resistor-inductor, or R-L, circuit can model a three-phase short circuit when the switch closes at the start of the time period. In this fault condition, all three phases of an unloaded synchronous machine are short-circuited. With no fault impedance and no initial current, the starting voltage depends on the source voltage phase angle. Kirchhoff's Voltage Law, or KVL, is used to analyze the circuit and find the total asymmetrical fault current. This current has two parts. The AC...

three-phase short circuit&#8212;unloaded synchronous machine

A three-phase short circuit on an unloaded synchronous machine shows how fault current changes over time. The AC fault current, with the DC offset removed, starts at a high value and then falls to a steady-state level in one phase of the machine. This change happens because of the magnetic flux created by the short-circuit armature currents. At first, these currents flow through high-reluctance paths. They later shift to lower-reluctance paths, which increases the armature inductance. This...

power system three-phase short circuits

Subtransient Fault Current in Power Systems

Subtransient fault current analysis in a power system uses simplified models for the main equipment. Transformers are represented by their leakage reactances. Transmission lines are modeled with equivalent series reactances, and synchronous machines are treated as constant voltage sources behind their subtransient reactances. Several elements are left out of the calculation because their effect on the immediate fault current is small or they make the model harder without changing the result...

bus impedance matrix

Three-Phase Fault Current Analysis

Three-phase fault current analysis in an N-bus power system uses the positive-sequence network and the bus impedance matrix. It helps estimate subtransient fault currents when a short circuit occurs at one bus. The method uses superposition, which means the problem is split into two circuits that are studied separately. In the first circuit, all machine voltage sources are short-circuited. Only the prefault voltage source at the faulted bus remains. The positive-sequence bus impedance matrix...

circuit breaker and fuse selection

Protective Devices in Power Systems

Circuit breakers and fuses protect electrical systems from fault current and overcurrent. They help stop damage when current rises above safe limits. Both devices are chosen based on the needs of the electrical system. A circuit breaker interrupts fault current by separating its contacts. This creates an arc, which must be extinguished by elongation, cooling, or splitting, depending on the breaker design. Breakers are grouped by operating voltage and by the arc-extinguishing medium, such as...

sequence networks of rotating machines

Generator Sequence Currents and Impedances

Generator sequence currents and impedances explain how a Y-connected synchronous generator behaves under balanced and unbalanced conditions. When the generator is grounded through a neutral impedance, it is set up to produce balanced internal phase voltages with only positive-sequence components. The source voltage therefore appears only in the positive-sequence network, and the line-to-ground voltages at the generator terminals show the sequence components of this setup. Zero-sequence current...

per-unit sequence models

Transformer Sequence Networks in Per Unit

Transformer sequence networks in per unit show how three-phase transformers respond to positive-, negative-, and zero-sequence currents. For an ideal Y-Y transformer grounded through neutral impedances, the per-unit sequence networks act much like those of a single-phase ideal transformer when the current is balanced. Balanced positive-sequence and negative-sequence currents do not create neutral current, so they do not cause voltage drops across the neutral path. Zero-sequence current behaves...

fault types

Power System Faults in Sequence Networks

Power system faults can be analyzed by moving between the phase domain and the sequence domain. This approach helps relate fault currents and voltages for three-phase bus faults and keeps the fault impedance in the model. Fault impedance is zero for a bolted fault, equal to the arc impedance for an arcing fault, and it represents the total fault impedance for a transmission-line insulator flashover. For a single line-to-ground fault from phase A to ground, the phase-domain conditions are...

key terms and concepts

Study how a three-phase short circuit changes fault current in an unloaded synchronous machine, from sub-transient response to steady-state behavior.

Synchronous Machine Fault Current Decay | JoVE K12

JoVE Core Electrical Engineering offers easy-to-understand animated videos that cover fundamental concepts of electric circuits along with circuit analysis techniques. It incorporates first-order and second-order circuits using operational amplifiers and circuit transformation concepts. The inclusion of practical design examples and real-world applications through scientist-in-action videos adds significant educational value, making complex concepts accessible.

electrical engineering

Synchronous Machine Fault Current Decay

Description

Transcript

Tags