Name: wood fastener types and uses
Uploaded: 2024-09-12T16:16:32.000Z
Duration: 1 min 18 s
Channel: JoVE

W konstrukcjach drewnianych łączniki utrzymują elementy na miejscu. Wytrzymałość połączenia zależy głównie od bezpośredniego łożyska pręta.
Różne elementy złączne, takie jak gwoździe, to ostro zakończone metalowe kołki wbijane w drewno młotkiem lub pistoletem mechanicznym.
Istnieje szeroka gama rodzajów gwoździ o różnych średnicach, i długościach.
Gwoździowanie czołowe, gwoździe końcowe i gwoździe u nóg to trzy techniki stosowane do mocowania drewnianych elementów za pomocą gwoździ.
Wkręty, które są łącznikami z gwintami spiralnymi, występują w różnych typach i są instalowane poprzez wykonanie ruchu skręcającego, aby bezpiecznie osadzić je w drewnie.
To działanie powoduje, że gwinty mocno wciągają w materiał, który mocuje.
umieszcza się we wstępnie wywierconych otworach za pomocą klucza, aby obrócić nakrętkę po stronie przeciwnej do łba, a śruba jest dokręcana i zabezpieczana na miejscu.
Płaskie stalowe podkładki pod i nakrętką rozprowadzają siłę na większej powierzchni drewna, zmniejszając zgniatanie włókien.
Łączniki z pierścieniem dzielonym, płytki zębate i metalowe urządzenia ramowe są również stosowane w połączeniach prętów drewnianych, aby służyć do mocowania.

Łączniki drewniane

Wood Fasteners

W konstrukcji drewnianej łączniki są niezbędne do łączenia elementów, a siła połączenia w dużej mierze zależy od bezpośredniej nośności między elementami. Stosowane są różne rodzaje łączników, każdy dostosowany do konkretnych zastosowań i wymagań konstrukcyjnych.

Najczęściej stosowanymi łącznikami są gwoździe, składające się z ostro zakończonych metalowych kołków wbijanych w drewno za pomocą młotka lub mechanicznego pistoletu do gwoździ. Występują w różnych średnicach, główkach i długościach. Techniki wbijania gwoździ obejmują face nailing, end nailing i toe nailing, a każda z metod zapewnia różne kąty i wytrzymałość połączeń elementów drewnianych.

Śruby to inny rodzaj łącznika, charakteryzujący się spiralnymi gwintami, które umożliwiają pewny chwyt po wkręceniu w drewno. Montaż obejmuje ruch skręcający, który wciąga śrubę w drewno, tworząc mocne trzymanie. Śruby są dostępne w różnych typach, każdy przeznaczony do konkretnych zastosowań.

Śruby zapewniają bardziej wytrzymałe połączenie. Są to łączniki gwintowane, które są wkładane do wstępnie wywierconych otworów. Nakrętka służy do zabezpieczenia śruby i jest ona dokręcana kluczem. Płaskie stalowe podkładki umieszczone pod łbem śruby i nakrętką pomagają rozłożyć siłę na większym obszarze, zapobiegając zgniataniu włókien drewna.

Inne elementy złączne, takie jak łączniki pierścieniowe, płytki zębate i metalowe urządzenia ramowe, również odgrywają kluczową rolę w konstrukcji drewnianej, zwiększając trwałość i integralność konstrukcji drewnianych. Te elementy złączne są niezbędne do utrzymania stabilności konstrukcyjnej i zapewnienia długowieczności konstrukcji drewnianych.

W konstrukcjach drewnianych łączniki utrzymują elementy na miejscu. Wytrzymałość połączenia zależy głównie od bezpośredniego łożyska pręta.
Różne elementy złączne, takie jak gwoździe, są ...

Education

JoVE Core

Civil Engineering

Inżynieria lądowa

Unit 1

Jednostka 1

Wood

Drewno

KEY TERMS AND CONCEPTS

KLUCZOWE TERMINY I POJĘCIA

wood fastener types and uses

Wood fasteners connect parts of a wood structure and help keep members in place. The strength of the connection depends mainly on direct bearing between the wood members. Different fasteners are chosen for different jobs and structural needs.

Nails are the most common wood fasteners. They are sharp-pointed metal pins that are driven into wood with a hammer or a mechanical nail gun. Nails come in many diameters, head styles, and lengths.

Nailing methods also matter. Face nailing places the nail through the face of one member. End nailing drives the nail into the end of a board, and toe nailing places it at an angle for a stronger connection between members.

Screws use spiral threads to hold firmly in wood. A screw is twisted into place, and that turning motion pulls it deeper into the wood. Different screw types are made for different uses.

Bolts provide a stronger connection and are used with predrilled holes. A nut secures the bolt, and a wrench tightens the nut. Flat steel washers under the bolt head and nut spread the force over a larger area and help prevent the wood fibers from being crushed.

Other wood connectors also support strong construction. Split-ring connectors, toothed plates, and metal framing devices help improve the durability and integrity of wood structures. These fasteners are important for structural stability and for helping wood constructions last longer.

Wood Fastener Types and Uses

introduction to wood

Wood Structure and Uses in Building

Wood is a construction material made from trees. A tree trunk has several layers. The outside is a protective layer of dead bark. Under that is living bark, then the cambium, then sapwood. As sapwood matures, it becomes heartwood. The pith sits at the center of the trunk. The age of a tree can be read from its growth rings. These rings are concentric bands seen in a trunk cross-section. Wood strength also depends on grain. Grain refers to elongated, tubular cells that run along the length of...

softwoods and hardwoods

Wood Grain in Softwoods and Hardwoods

Softwoods and hardwoods come from different kinds of trees, and their leaf structures and cell makeup help explain how they are used. Softwoods come from cone-bearing trees with needle-like leaves. Hardwoods usually come from trees that shed broad leaves seasonally. Softwoods are made mostly of long cells called tracheids and a smaller number of rays, which are radial cells. This simpler structure gives softwoods a rougher grain. Because of this, they are often used in construction for...

lumber

Lumber Cutting Methods

Lumber is made from logs that are harvested, debarked, and processed into long pieces with a rectangular cross-section. The process starts when an automated saw slices a log into slabs. Those slabs then move on a conveyor belt to smaller saws, where they are cut into square-edged pieces of specific widths. Freshly cut lumber usually has rough surfaces. Its dimensions may also vary slightly from one end to the other. The way wood is cut affects both the lumber’s appearance and how it is used. <br...

structural properties and dimensions of lumber

structural-properties-and-dimensions-of-lumber

Wood Strength Tests and Lumber Sizes

Wood strength depends on how its fibers are aligned along the length of the tree. This alignment gives wood much greater tensile strength along the grain than across it, sometimes up to twenty times higher. Wood also tends to perform better under compression than under tension. Fiber length varies by wood type. Hardwoods have fibers about one twenty-fifth of an inch long. Softwoods have longer fibers that range from one-eighth to one-third of an inch. Laboratory tests help measure how wood...

seasoning of wood

Wood Drying for Stronger Construction

Seasoning of wood is the drying process used to lower and stabilize moisture content before wood is used in construction. Fresh wood can swell when it takes in moisture and contract as it dries. Seasoning helps reduce that movement so the wood stays more stable after it is built into a structure. The main goal is to reach equilibrium moisture content. This is the point where the wood’s moisture level matches the moisture in the surrounding environment. When wood is seasoned properly, it is...

wood surfacing

Wood Surfacing for Smooth, Safe Lumber

Wood surfacing smooths lumber, improves its size accuracy, and makes it safer to handle. It is a key finishing step in woodworking and construction. The process also helps correct small distortions that can form as wood dries. Before surfacing, the wood may be sized slightly larger to account for shrinkage during seasoning, which is the drying stage. A plane, a tool with rotating blades, is used to remove material and smooth the surface. The same tool can also round the edges a little, which...

lumber defects

Common Wood Flaws in Lumber

Lumber defects are flaws in wood that can change both its appearance and its strength. These defects come from tree growth and from the way lumber is processed. Knowing the main defects helps explain why some boards are better for construction and manufacturing than others. Some defects begin in the tree itself. Knots form where branches were once attached to the trunk, and knotholes appear when those knots fall out. Decay and insect damage are also natural defects that can weaken wood and...

wood fasteners

Wood fasteners connect parts of a wood structure and help keep members in place. The strength of the connection depends mainly on direct bearing between the wood members. Different fasteners are chosen for different jobs and structural needs. Nails are the most common wood fasteners. They are sharp-pointed metal pins that are driven into wood with a hammer or a mechanical nail gun. Nails come in many diameters, head styles, and lengths. Nailing methods also matter. Face nailing places the...

veneer

How Veneer Is Cut and Used

Veneer is a thin sheet of wood that is usually about one-eighth of an inch thick or less. It is made to show the look of wood while using timber more efficiently. Veneer is common in furniture and other finished wood products. One common way to make veneer is rotary cutting. In this method, a log is mounted in a large lathe and spun against a knife edge. As the knife moves deeper into the turning log, it peels off a continuous strip of wood. This creates rotary-cut veneer. Other veneer...

wood products

Engineered Wood Products in Construction

Engineered wood products are made from wood strands, veneers, lumber, and even waste wood shreds. They are used in both structural and nonstructural building applications. These materials are designed to improve strength, durability, and versatility in modern construction. Glue-laminated wood, or glulam, is made by bonding several smaller pieces of dimensional lumber with adhesive. Cross-laminated timber uses solid lumber panels with layers placed so the grain direction alternates. This layer...

wood panel products

Types of Wood Panels in Construction

Wood panels are common construction materials used for flooring, siding, and roofing. They usually come in standard 4-foot by 8-foot sheets. Their thickness can range from one-quarter of an inch to one and one-eighth inches. Plywood is one of the most familiar wood panels. It is made by gluing thin wood veneers, or layers, under pressure. The outer veneer grain runs lengthwise, while the inner layers run widthwise. Plywood also has an odd number of layers, which helps keep the panel...

key terms and concepts

Learn how nails, screws, bolts, washers, and other wood connectors hold wood members together and support strong, stable construction.

Wood Fastener Types and Uses | JoVE K12

JoVE Core Civil Engineering provides a foundational exploration of essential construction materials in civil engineering, focusing on bricks, stones, steel, wood, and concrete through easy-to-understand animated videos. This collection covers the properties, manufacturing processes, and practical applications of these materials. Additionally, the accompanied science-in-action videos demonstrate the research experiments performed in laboratories.

civil engineering

Wood Fastener Types and Uses

Description

Transcript

Tags