Name: stress components on a loaded body
Uploaded: 2024-03-07T13:22:33.000Z
Duration: 1 min 15 s
Channel: JoVE

Considere um corpo submetido a múltiplas cargas. Quando dissecado através de um ponto usando um plano paralelo ao plano xy, observa-se que as forças de cisalhamento atuam em uma pequena área ao redor do ponto.
Considere uma parte do corpo submetida às cargas mostradas anteriormente, com a força normal atuando ao longo do eixo z
As forças de cisalhamento não têm uma direção bem definida em um plano seccional, portanto, são resolvidas em duas forças componentes paralelas aos eixos x e y.
A magnitude de cada força é então dividida pela área para obter os componentes de tensão.
O primeiro subscrito nas tensões indica que elas são exercidas na superfície perpendicular ao eixo z. O segundo subscrito em tensões de cisalhamento identifica a direção.
Quando o outro lado do plano vertical é analisado, ele produz os mesmos componentes de tensão, mas em direções opostas.
Ao passar seções através do ponto paralelo aos planos yz e zx, componentes de tensão adicionais podem ser definidos.

estresse: condições gerais de carga

Stress: General Loading Conditions

Para compreender a complexidade das condições do mundo real, onde múltiplas cargas são aplicadas simultaneamente a uma estrutura, pode-se visualizar uma seção passando por um ponto específico dentro de um corpo, alinhado paralelamente ao plano xy. Esta seção está sujeita a várias forças, incluindo cargas originais, forças normais e forças de cisalhamento.


 A força de cisalhamento, possuindo direcionalidade potencial dentro do plano da seção, é simplificada em duas forças componentes que correm paralelamente aos eixos x e y. Cada força é dividida pela área e, à medida que se aproxima de zero, três componentes de tensão distintos (σ_z, τ_zx e τ_zy) são definidos. O subscrito inicial nestes componentes significa que as tensões são exercidas em uma superfície perpendicular ao eixo z, enquanto o segundo subscrito identifica a direção do componente.


 Os sinais destes componentes de tensão indicam tensão (positiva) ou compressão (negativa). Uma análise semelhante na parte direita do corpo resulta em componentes de tensão idênticos, mas em direções opostas. Componentes de tensão adicionais podem ser determinados passando seções através do ponto paralelo aos planos yz e zx. Esta análise ajuda a desvendar a complexa interação de forças e tensões sob condições de carga complexas.

Estresse: Condições Gerais de Carga

Considere um corpo submetido a múltiplas cargas. Quando dissecado através de um ponto usando um plano paralelo ao plano xy, observa-se que o cisalhamento ...

Education

JoVE Core

Mechanical Engineering

Engenharia Mecânica

Unit 1

Unidade 1

Concept of Stress

Conceito de Estresse

KEY TERMS AND CONCEPTS

TERMOS-CHAVE E CONCEITOS

stress components on a loaded body

Stress components on a loaded body can be found by cutting the body through a point with a plane parallel to the xy plane. That section carries the original loads, along with normal forces and shearing forces. The result is a simple way to describe how a structure responds under combined loading.

The shearing force in the section can point in different directions within the plane. It is split into two parts that run parallel to the x and y axes. Each part is divided by the area, and as that area becomes very small, three stress components are defined: σz, τzx, and τzy.

The first subscript in each symbol shows the surface orientation. It means the stress acts on a surface perpendicular to the z-axis. The second subscript shows the direction of the stress component. The sign of each stress component shows whether the material is in tension, which is positive, or compression, which is negative.

If the body is viewed on the right side of the cut, the same stress components appear in opposite directions. Similar stress components can also be found by making sections parallel to the yz and zx planes. This method helps describe the full set of stresses that can act at a point when several loads act at once.

Stress Components on a Loaded Body

normal stress

Normal Stress in Axial Loading

Normal stress acts perpendicular to a material’s cross-sectional area. It appears when a force is applied along the axis of an object, which is called axial loading. Bridge truss members are a practical example of this kind of loading. When a rod carries axial load, internal forces develop across the section. Because these forces act normal to the plane of the section, the stress is called normal stress. Stress here means the average stress over the whole cross-section, not the value at one...

shearing stress

Shear Forces in Bolts and Rivets

Shearing stress is caused by transverse forces acting on an object. These forces create internal forces in the plane where the external forces are applied. The total internal force in that section is called the shear. Average shearing stress is found by dividing the shear by the cross-sectional area. This value is only an average, because shear stress is not spread evenly across the section. It can be zero at the surface and much higher than the average in other areas. Bolts, pins, and rivets...

bearing stress

Bolt-to-Plate Contact Pressure

Bearing stress is the contact pressure between two separate bodies. A common example is a bolt pushed through a plate. The bolt applies a force to the plate, and the plate pushes back with an equal and opposite force. That force is not a single point load. It is made up of many smaller forces spread across the contact surface between the bolt and the plate. Because these microforces are complex, engineers use an average value called bearing stress. Bearing stress is found by dividing the...

applications of stress

Boom and Rod Stress Analysis

Boom and rod stress analysis shows how a pinned support structure carries a load. The boom and the rod are connected by a pin and held in place by brackets and pins. The structure is then separated from its supports so the forces can be studied clearly. A free-body diagram is drawn to identify every force on the boom, the rod, and the load. The reaction forces on both members are found using equilibrium equations. At point P, the reaction causes compression in the boom. At point R, the...

stress on an oblique plane

Axial Load Stress on Inclined Sections

Axial loading creates stress in a material along its central axis. This kind of load can cause compression or elongation, and it produces normal stress. Normal stress acts perpendicular to the material area and can be either tensile or compressive. When the section is not perpendicular to the load, it becomes an oblique plane. On this inclined plane, the stress state includes both normal stress and shearing stress. Shearing stress acts parallel to the area and changes shape without changing...

stress: general loading conditions

Stress components on a loaded body can be found by cutting the body through a point with a plane parallel to the xy plane. That section carries the original loads, along with normal forces and shearing forces. The result is a simple way to describe how a structure responds under combined loading. The shearing force in the section can point in different directions within the plane. It is split into two parts that run parallel to the x and y axes. Each part is divided by the area, and as that...

components of stress

Stress Components on a Cube at a Point

Stress components on a small cube help describe how a body behaves under multiple loading. The cube is centered at point O and has stress acting on all six faces, whether the faces are visible or hidden. Normal stress components σx, σy, and σz act perpendicular to the x, y, and z axes. Shearing stress components also act on the cube faces. The visible faces carry shear stresses such as τxy and τxz. The hidden faces carry equal and opposite stresses. This balance keeps the cube in equilibrium.

design consideration

Safety Factors in Structural Design

Safety factors in structural design help engineers choose a material and loading limit that can be used safely. The process begins with a material’s ultimate strength. This value comes from tests that increase force until the material reaches its breaking point or limit. The ultimate load is then divided by the original cross-sectional area to find the ultimate normal stress, or strength. Ultimate shearing stress is another key value used in design. These limits show how much stress a material...

key terms and concepts

Learn how to find stress components on a loaded body using cuts through a point. See normal and shear stresses on xy, yz, and zx planes.

Stress Components on a Loaded Body | JoVE K12

O JoVE Core Mechanical Engineering oferece vídeos animados concisos e de fácil compreensão que abrangem tópicos-chave como equilíbrio, forças, análise de treliças e mecânica estrutural. Explore suas aplicações no mundo real e observe esses conceitos em ação por meio de experimentos conduzidos por cientistas.

mechanical engineering

Stress Components on a Loaded Body

Description

Transcript

Tags