Name: how three-phase power delivers electricity
Uploaded: 2024-07-08T13:19:57.000Z
Duration: 1 min 22 s
Channel: JoVE

Как правило, системы распределения питания переменного тока классифицируются как однофазные, двухфазные или трехфазные.
Однофазные цепи включают в себя один источник, подключенный к нагрузкам через двухпроводные системы.
Однофазные системы используются в домашних хозяйствах для питания приборов напряжением 120 В и 240 В, таких как лампы, телевизоры или центральные кондиционеры.
Двухфазная трехпроводная система имеет два источника, где напряжение, вырабатываемое вторым, отстает от другого на 90 градусов.
В отличие от этого, трехфазная четырехпроводная система состоит из трех источников с одинаковой амплитудой, частотой и разностью фаз 120 градусов, подключенных к трем нагрузкам.
Трехфазный источник и трехфазная нагрузка могут быть подключены по оси Y или треугольнику.
Эти цепи используются в промышленных приложениях, например, для питания асинхронного двигателя, при необходимости они могут использоваться для обеспечения однофазных входов.
Мгновенная мощность в этих системах имеет гораздо меньшую пульсацию, чем в однофазной системе, что обеспечивает более равномерную передачу мощности и меньшую вибрацию.
Они требуют меньше материала проводника или провода для передачи той же мощности, что делает их более экономичными, чем однофазные.

Трехфазные цепи

Three-Phase Circuits

Системы переменного тока для распределения электроэнергии делятся на три категории: однофазные, двухфазные и трехфазные системы. Однофазная система, распространенная в жилых помещениях, обычно представляет собой двухпроводную систему, подключающую один источник переменного тока к различным нагрузкам. Эти схемы поддерживают стандартную бытовую технику, работающую при напряжении 120 В (В) и 240 В, например лампы, телевизоры и микроволновые печи. Первые генераторы, установленные в 1895 году на гидроэлектростанции Ниагарского водопада, были двухфазными, и спроектировал их Никола Тесла. Двухфазная система питания встречается реже, как правило это трехпроводная система, и она включает в себя два источника напряжения, сдвинутых по фазе друг с другом на 90 градусов.
Трехфазная четырехпроводная система наиболее распространена в промышленности. Эта система состоит из трех источников переменного тока, идентичных по амплитуде и частоте, но имеющих между собой разность фаз в 120 градусов. Нагрузки в такой системе могут быть подключены либо по схеме Y (уай, звезда), либо по схеме Δ (дельта, треугольник).
Преимущество трехфазных цепей заключается в их эффективности и стабильности. Они обеспечивают мощность с меньшей пульсацией, чем однофазные системы, что приводит к более плавной передаче мощности и минимизации вибраций — решающего фактора для промышленного оборудования, такого как асинхронные двигатели. Еще одним преимуществом является уменьшение количества проводникового материала, необходимого для передачи заданного количества энергии, что делает трехфазные системы более экономичными, чем их однофазные аналоги.
Связь между линейными и фазными напряжениями и токами в трехфазных системах, соединенных по оси Y, определяется выражением:
<img alt="Equation 1" src="/files/ftp_upload/15126/15126_Equation_1.svg" style="height: 22px;">
<img alt="Equation 2" src="/files/ftp_upload/15126/15126_Equation_2.svg" style="height: 22px;">
А для Δ-связных систем:
<img alt="Equation 3" src="/files/ftp_upload/15126/15126_Equation_3.svg" style="height: 20px;">
<img alt="Equation 4" src="/files/ftp_upload/15126/15126_Equation_4.svg" style="height: 22px;">
Эти уравнения показывают взаимосвязь между линейными напряжениями и токами в каждой фазе, что важно при расчете общей мощности в трехфазных системах. Общую мощность для соединений Y и Δ можно найти с помощью:
<img alt="Equation 5" src="/files/ftp_upload/15126/15126_Equation_5.svg" style="height: 20px;">
где φ – угол коэффициента мощности, влияющий на эффективность передачи электроэнергии.

Как правило, системы распределения питания переменного тока классифицируются как однофазные, двухфазные или трехфазные.
Однофазные цепи включают в себя один источник ...

Education

JoVE Core

Electrical Engineering

Электротехника

Unit 1

Раздел 1

KEY TERMS AND CONCEPTS

ОСНОВНЫЕ ТЕРМИНЫ И ПОНЯТИЯ

how three-phase power delivers electricity

Three-phase power is a major part of AC power distribution, especially where steady and efficient electricity delivery is needed. AC systems are grouped into single-phase, two-phase, and three-phase systems. These categories help describe how power moves from the source to the load.

Single-phase circuits are common in homes. They usually use a two-wire system that connects one AC source to loads. These circuits can supply everyday appliances such as lamps, televisions, and microwaves at 120 V and 240 V.

Two-phase supply systems are less common. The first generators at the Niagara Falls hydro plant, installed in 1895, used two-phase power and were designed by Nikola Tesla. In a two-phase system, a three-wire setup uses two voltage sources that are 90 degrees out of phase.

Three-phase systems are used most often in industrial settings. A three-phase, four-wire system uses three AC sources with the same amplitude and frequency, and each source is shifted by 120 degrees. Loads in these systems can be connected in a Y, or star, configuration or in a delta (Δ) configuration.

Three-phase circuits are valued for efficiency and stability. They deliver power with less pulsation than single-phase systems, so the flow is smoother and vibrations are reduced. This matters for industrial machines such as induction motors. Three-phase systems also need less conductor material to deliver the same amount of power, which makes them more cost-effective than single-phase systems.

The line and phase values are related differently in Y-connected and Δ-connected systems. These relationships between line-to-line voltage and current and the values in each phase are important when calculating total power. Total power in both Y and Δ connections is found using an equation that includes the power factor angle, φ, which affects power transmission efficiency.

How Three-Phase Power Delivers Electricity

how-three-phase-power-delivers-electricity

three-phase circuits

Three-phase power is a major part of AC power distribution, especially where steady and efficient electricity delivery is needed. AC systems are grouped into single-phase, two-phase, and three-phase systems. These categories help describe how power moves from the source to the load. Single-phase circuits are common in homes. They usually use a two-wire system that connects one AC source to loads. These circuits can supply everyday appliances such as lamps, televisions, and microwaves at 120 V...

generation of three-phase voltage

Three-Phase AC Generator Windings

A three-phase AC generator uses rotating magnet windings and a stationary stator to make three-phase voltage. The rotor carries a magnet that spins inside the stator. The stator holds the three-phase winding, and mutual induction creates the voltage. The stator windings are spread evenly around the inside of the stator. They are placed 120 electrical degrees apart. These windings consist of three separate coils, or groups of coils, called phases. The phases can be connected in a Y, or star,...

three-phase voltages

Three-Phase Power Connections

Three-phase power connections use balanced voltages that are equal in magnitude and separated by 120 degrees. A three-phase generator produces these voltages, and the balance helps reduce power loss while keeping energy delivery steady to connected loads. Three-phase sources can be arranged in either wye or delta form. The loads connected to the system can also use wye or delta. This flexibility gives control over how the system is designed and managed. In a wye connection, one end of each...

the y-to-y circuit

Balanced Wye-to-Wye Neutral Current

A balanced wye-to-wye circuit uses three wye-connected sinusoidal voltage sources and three wye-connected loads. A neutral wire links the neutral node of the source to the neutral node of the load. The load impedance is connected across each phase of the load. The source and load can be connected in either a four-wire or a three-wire arrangement. A three-phase system is balanced when each phase has the same load. In that case, the current flow and phase angle are uniform across the system. If...

the y-to-delta circuit

Wye Source and Delta Load Currents

A balanced wye source and delta load form a common three-phase circuit with no neutral line connection. The source is Y-connected, and the load is delta-connected. To analyze the circuit, the first step is to assume a positive phase sequence. These phase voltages are then used to find the line voltages that appear across the delta load impedances. In the wye source, the phase voltages are V an, V bn, and V cn. In the delta load, the line voltages are V ab, V bc, and V ca. These line voltages...

the delta-to-delta circuit

Balanced Delta-Delta Power Circuit

A balanced delta-delta power circuit uses a delta-connected source and a delta-connected load. The two deltas form a closed loop that creates three separate phases. In this setup, the phase voltages are the same as the line voltages. If the source is in positive sequence, the phase voltages can be written directly, and no neutral wire is needed. The delta-connected load current is found by dividing the phase voltage by the impedance of each phase. For line current, Kirchhoff’s Current Law...

the delta-to-y circuit

Delta-Wye Source and Load Connections

A balanced delta-wye circuit connects a delta-connected source to a wye-connected load. In this setup, the phase voltage of the delta source equals the line voltage of the wye load. The source also sets the line currents that flow into the load. For a balanced system, the phase difference between currents makes it possible to find one line current from the other by using the positive sequence of phases. In the wye-connected load, each phase current equals the line current from the delta source.

power in a three-phase circuit

Balanced Three-Phase Power Calculation

Balanced three-phase power calculation depends on the wye and delta connections used in the circuit. A wye, or star, configuration can use three wires or four wires. A delta configuration connects the components in a closed loop. These connection types change how voltages and currents are arranged, but both are used in three-phase systems. In a balanced three-phase system, instantaneous power is the power at one exact moment. Even though the power in each phase changes over time, the total...

power distribution in three-phase and single phase circuits

power-distribution-in-three-phase-and-single-phase-circuits

Single-Phase vs. Three-Phase Power Loss

Single-phase and three-phase circuits distribute electrical power in different ways. Single-phase power is common in homes, while balanced three-phase power is widely used in industrial settings with heavy machinery. Both systems deliver energy, but their current flow and wire needs are not the same. A single-phase circuit usually uses a two-wire system. The current depends on the power absorbed by the load and the line voltage. Because wire loss from resistance follows the square of the...

line loss

Reducing Power Loss in Three-Phase Lines

Three-phase power lines can lose energy as electricity travels from the source to the load. This line loss affects how efficiently power reaches the load. In balanced three-phase circuits, the symmetry makes the analysis easier because one phase can represent the whole system. The source-load connection can use wye, also called star, or delta configurations. These setups change the relationship between line voltage, phase voltage, line current, and phase current. A per-phase equivalent circuit...

reducing line loss

Cutting Heat Loss in Three-Phase Lines

Three-phase power systems can lose energy as heat in transmission lines because the wires have resistance. This line loss becomes important when electricity travels over a distance. A common solution is to use transformers to change the voltage and current in the system. The setup uses two three-phase transformers. A step-up transformer is placed at the source, and a step-down transformer is placed at the load. Raising the voltage at the source lowers the current in the transmission lines, and...

key terms and concepts

Explore how three-phase AC power works, why industry uses Y and delta connections, and how smoother, more efficient power delivery is calculated.

How Three-Phase Power Delivers Electricity | JoVE K12

JoVE Core Electrical Engineering offers easy-to-understand animated videos that cover fundamental concepts of electric circuits along with circuit analysis techniques. It incorporates first-order and second-order circuits using operational amplifiers and circuit transformation concepts. The inclusion of practical design examples and real-world applications through scientist-in-action videos adds significant educational value, making complex concepts accessible.

electrical engineering

How Three-Phase Power Delivers Electricity

Description

Transcript