Name: reading frequency response on bode plots
Uploaded: 2024-07-08T13:20:02.000Z
Duration: 1 min 26 s
Channel: JoVE

Рассмотрим блок электрокардиограммы, в котором используется фильтр нижних частот со сложной сетевой функцией, представленной его величиной и фазовым углом.
Логарифмическое усиление в децибелах вычисляется путем умножения десятичного логарифма величины сетевой функции на 20.
Диаграммы Боде представляют собой полулогарифмические графики, отображающие логарифмическое усиление в децибелах и фазовый угол в градусах по частотам.
На более низких частотах логарифмическое усиление и фазовый угол стремятся к нулю.
В результате на графике Боде образуются горизонтальные линии, известные как низкочастотные асимптоты.
На более высоких частотах расчеты коэффициента усиления и фазового угла отражают их зависимость от частоты.
Они изображаются в виде прямых линий с отрицательным наклоном и известны как высокочастотные асимптоты.
Низко- и высокочастотные асимптоты пересекаются в одном углу, известном также как угловая частота.
На этой частоте асимптотическая амплитуда отклоняется почти на -3 децибела от точного значения, а фазовый угол составляет примерно -45 градусов.
Асимптотические графики Боде являются хорошими приближениями к фактическим графикам Боде.

Графики Боде

Графики Боде — это графические инструменты, в которых используются логарифмические шкалы частоты по оси X и усиления в децибелах по оси Y. Этот логарифмический метод позволяет компактно отображать широкий диапазон частот, что позволяет анализировать влияние компонентов на поведение схемы в широком частотном спектре.
Сетевая функция представляет собой отношение выхода системы к ее входу, при этом величина и фазовый угол получаются из сложной сетевой функции. Логарифмическое усиление в децибелах определяется путем умножения десятичного логарифма величины сетевой функции на 20. Прирост на графике Боде выражается логарифмически. Единицей логарифмического усиления является децибел, также известный как усиление в дБ. Децибелы (дБ) определяют количественное усиление, где 1 дБ — это одна десятая часть Белла, в честь Александра Грэма Белла.
Графики Боде, представляющие собой полулогарифмические графики, показывают логарифмический коэффициент усиления в децибелах и фазовый угол в градусах в диапазоне частот. Эти графики облегчают понимание частотной характеристики системы.
На более низких частотах и ​​логарифмический коэффициент усиления, и фазовый угол приближаются к нулю, образуя горизонтальные линии на графике Боде, известные как низкочастотные асимптоты. Эти линии указывают на минимальное влияние фильтра на сигналы на этих частотах. По мере увеличения частоты расчеты усиления и фазового угла отражают их частотную зависимость. На графике Боде эти зависимости выглядят как прямые линии с отрицательным наклоном, называемые высокочастотными асимптотами. Эти линии демонстрируют, как фильтр ослабляет высокочастотные сигналы. Низкочастотная и высокочастотная асимптоты пересекаются на угловой частоте. Здесь асимптотическая величина отклоняется примерно на -3 децибела от точного значения, что указывает на значительное изменение отклика фильтра. Кроме того, фазовый угол на угловой частоте составляет примерно -45 градусов.
Асимптотические графики Боде обеспечивают разумную аппроксимацию реальных графиков Боде, позволяя упростить анализ при сохранении приемлемой точности.

Рассмотрим блок электрокардиограммы, в котором используется фильтр нижних частот со сложной сетевой функцией, представленной его величиной и фазовым углом.
Тем...

Education

JoVE Core

Electrical Engineering

Электротехника

Unit 1

Раздел 1

Frequency Response

Частотная характеристика

KEY TERMS AND CONCEPTS

ОСНОВНЫЕ ТЕРМИНЫ И ПОНЯТИЯ

Bode Plots

reading frequency response on bode plots

Bode plots show how a circuit or system responds across frequency. They use a logarithmic frequency scale on the x-axis and gain in decibels on the y-axis. This format makes it easier to display a wide range of frequencies and to see how circuit parts affect behavior over that range.

A network function gives the ratio of output to input for a system. Its complex form provides both magnitude and phase angle. The logarithmic gain on a Bode plot comes from the magnitude, calculated by multiplying the base-ten logarithm of that magnitude by 20. The gain is measured in decibels, or dB. A decibel is one-tenth of a bel, and the unit honors Alexander Graham Bell.

Because Bode plots are semilogarithmic graphs, they show gain in dB and phase angle in degrees over frequency. This makes the frequency response of a system easier to study. At low frequencies, both gain and phase angle approach zero. These flat regions are called low-frequency asymptotes, and they show that the filter has little effect on the signal there.

As frequency rises, the gain and phase angle change with frequency. On the plot, this appears as straight lines with negative slopes called high-frequency asymptotes. These lines show that the filter attenuates higher-frequency signals. The low- and high-frequency asymptotes meet at the corner frequency. At that point, the asymptotic magnitude is about -3 decibels from the exact value, and the phase angle is about -45 degrees. Asymptotic Bode plots give a reasonable approximation of the actual plot and make analysis simpler while keeping useful accuracy.

Reading Frequency Response on Bode Plots

analyzing-filter-response-with-bode-plots

network function of a circuit

How Transfer Functions Shape Circuit Response

Transfer functions show how a circuit responds as signal frequency changes. They describe the link between input and output in frequency response analysis. This makes them useful for studying how circuits behave in electronics and engineering. A transfer function is a mathematical tool that relates phasor output to phasor input. It can be written as voltage gain, current gain, transfer impedance, or transfer admittance. The poles and zeros are the most important parts of the function. Zeros...

frequency response of a circuit

Inductive Circuit Frequency Response

Inductive circuit frequency response shows how a circuit with an inductor reacts to different frequencies. The analysis starts in the time domain and then moves into the frequency domain. In that step, the inductor is replaced by an impedance, and the circuit is written with phasors, which are sinusoidal signals shown with magnitude and phase. The transfer function describes how the output changes compared with the input at each frequency. A key parameter is the time constant, which is the...

gain

Circuit Gain and Phase Shift

Circuit gain and phase shift describe how a linear circuit changes a sinusoidal input voltage or current. These properties matter in circuits with reactive elements, because the response depends on the input frequency. As the frequency changes, the gain and phase shift also change. Gain compares the size of the output sinusoid to the size of the input sinusoid. If Vin is the input and Vout is the output, the gain K is the ratio of the output amplitude to the input amplitude. A gain greater...

bode plots

Bode plots show how a circuit or system responds across frequency. They use a logarithmic frequency scale on the x-axis and gain in decibels on the y-axis. This format makes it easier to display a wide range of frequencies and to see how circuit parts affect behavior over that range. A network function gives the ratio of output to input for a system. Its complex form provides both magnitude and phase angle. The logarithmic gain on a Bode plot comes from the magnitude, calculated by multiplying...

transfer function and bode plots-i

Transfer Function Gain and Origin Effects

Transfer function gain and poles or zeros at the origin shape a system's Bode plot. The transfer function is often written in standard form after the polynomial coefficients are normalized. In that form, the constant gain, zeros, poles, and quadratic terms all appear clearly. The poles and zeros mark critical frequencies where the output magnitude and phase change noticeably. The constant gain K creates a fixed magnitude and phase term. Its magnitude is 20 log 10 K in decibels, and its phase...

transfer function and bode plots-ii

Bode Plot Slope and Phase Changes

Bode plots show how a transfer function changes with frequency. The standard form includes constant gain, poles and zeros at the origin, simple poles and zeros, and quadratic poles and zeros. Each part shapes the system response in a different way. A simple zero sets the magnitude trend first. The Bode magnitude plot stays flat at low frequencies, near 0 dB, and then rises at 20 dB per decade after the corner or break frequency, ω1. That corner frequency is where the straight-line...

bode plots construction

Reading Frequency Response with Bode Plots

Bode plots show the frequency response of a system with a magnitude plot and a phase plot. Both plots use a logarithmic frequency axis. In control system analysis, this makes it easier to see how a transfer function changes with frequency. To build a Bode plot, start with the transfer function H(ω). After normalization, the function includes constant gain, zeros, and poles. Each term affects the plot in a different way. A constant gain of 10 gives a starting magnitude of 20 dB, since 20...

series resonance

Series Resonance in RLC Circuits

Series resonance in an RLC circuit happens when the inductive reactance and capacitive reactance are equal. An RLC circuit contains a resistor, an inductor, and a capacitor. The impedance of the circuit is the ratio of the supply voltage to the circuit current. At resonance, the imaginary part of the impedance becomes zero. The frequency at which this occurs is called the resonant frequency. It depends on the inductance (L) and capacitance (C) of the circuit. Mathematically, the resonant...

characteristics of series resonant circuit

characteristics-of-series-resonant-circuit

Series Resonance and RLC Filter Behavior

Series resonance in an RLC circuit happens when the inductor, capacitor, and resistor are connected in series. At the resonant frequency, the inductive reactance and capacitive reactance are equal in size but opposite in sign, so they cancel each other. As a result, the circuit impedance becomes very small and is mainly set by the resistance. The resonant frequency of a series RLC circuit can be calculated from its inductance and capacitance. At this frequency, the current reaches its maximum...

parallel resonance

Parallel RLC Tuning at Resonance

A parallel RLC circuit uses a resistor, inductor, and capacitor connected to the same nodes. Because they share the same voltage, the circuit is analyzed with admittance, which describes how easily current can flow. In a parallel RLC circuit, admittance helps show how the circuit responds as the frequency changes. Resonance happens when the net reactance is zero. At that point, the capacitive and inductive effects cancel each other out. The resonant frequency is found from this condition. At...

frequency response of op amp circuits

Op Amp Gain and Bode Plot Basics

Operational amplifiers are used for signal conditioning, filtering, and mathematical tasks such as addition, subtraction, integration, and differentiation. Their frequency response shows how amplifier gain changes as the input frequency changes. This makes the gain of an op-amp a key idea in circuit design. At low frequencies, an op-amp can hold a constant gain called the dc gain, A0. As frequency rises, the gain starts to drop after the corner frequency, or break frequency, ω1. In other...

passive filters

Audio Frequency Control with Passive Filters

Passive filters shape the frequency spectrum of electrical signals. They use only passive parts such as resistors, inductors, and capacitors. Because they do not need an external power source, they can let selected frequency ranges pass or block others in many applications. Low-pass filters pass signals below the cutoff frequency, ωc, and reduce signals above it. In audio systems, they can send bass frequencies to woofers or subwoofers. For an RC low-pass filter, the transfer function H(s)...

active filters

Active Filter Design and Frequency Response

Active filters use op-amps, resistors, and capacitors to shape a signal's frequency response. They remove unwanted frequency components while keeping the parts of the signal that are needed. The design depends on the choice of resistor and capacitor values, which set the cutoff points and help define the overall response. A first-order low-pass active filter passes signals below a cutoff frequency and reduces signals above it. Its transfer function includes the low-frequency gain, also called...

scaling

Circuit Component Scaling for Filters

Circuit component scaling helps turn simple circuit values into practical ones for filter design and circuit analysis. Engineers often start with standard values like 1 ohm, 1 henry, or 1 farad because they make examples and problems easier to work through. Later, those values can be scaled to more realistic levels. This method is useful in filters, resonant circuits, and many other circuit analysis problems. It reduces calculation complexity while keeping the circuit behavior easy to study.

design example

Touch-Tone Filter Design Example

Touch-tone telephony uses dual-tone multi-frequency (DTMF) signaling and a filter design example to show how keypad tones are separated. It replaced the old rotary dial with a matrix-style keypad arranged in four rows and three columns. Each of the 12 buttons produces a unique signal pair. Every key press creates two sinusoidal tones at the same time. One tone comes from a low-frequency group between 697 and 941 Hz. The other comes from a high-frequency group between 1209 and 1477 Hz. This...

key terms and concepts

Learn how Bode plots use decibels, phase angle, and asymptotes to show frequency response, including corner frequency and filter behavior.

Reading Frequency Response on Bode Plots | JoVE K12

JoVE Core Electrical Engineering offers easy-to-understand animated videos that cover fundamental concepts of electric circuits along with circuit analysis techniques. It incorporates first-order and second-order circuits using operational amplifiers and circuit transformation concepts. The inclusion of practical design examples and real-world applications through scientist-in-action videos adds significant educational value, making complex concepts accessible.

electrical engineering

Reading Frequency Response on Bode Plots

Description

Transcript