Name: touch-tone filter design example
Uploaded: 2024-07-08T13:20:03.000Z
Duration: 1 min 23 s
Channel: JoVE

K12 Standards

Next Generation Science Standards

High School

Physical Science

waves-and-their-applications-in-technologies-for-information-transfer

Waves and Their Applications in Technologies for Information Transfer

HS-PS4-2

Design Example

Инженер проектирует схему для акустической системы с требуемой частотой кроссовера 2 кГц, учитывая сопротивление динамика в 8 Ом.
Схема схемы соединяет кроссоверную сеть с усилителем звука, связывая ее с низкочастотными и высокочастотными динамиками.
Низкочастотный динамик – низкочастотный динамик – воспроизводит сигналы более низких частот, в то время как высокочастотный динамик – высокочастотный – воспроизводит сигналы более высоких частот.
Эквивалентная принципиальная схема включает в себя RC-фильтр верхних частот и RL-фильтр нижних частот, при этом усилитель представлен источником напряжения.
Частотная характеристика кроссоверной сети определяется с помощью передаточных функций для фильтров высоких и нижних частот.
Частота кроссовера фильтра верхних частот обратно пропорциональна произведению сопротивления и емкости.
И наоборот, частота кроссовера фильтра нижних частот прямо пропорциональна отношению сопротивления к индуктивности.
Известные значения частоты кроссовера и сопротивления динамика используются для расчета значений емкости и индуктивности.
Эта конструкция направляет частоты выше 2 кГц на высокочастотный динамик и частоты ниже 2 кГц на низкочастотный динамик.

Частотная характеристика

Инновация кнопочной телефонной связи произвела революцию в телекоммуникационной отрасли, заменив традиционный дисковый набор двухтональной многочастотной (DTMF) системой сигнализации. В этой системе используется клавиатура матричного типа с кнопками, расположенными в четырех рядах и трех столбцах, что создает 12 различных сигналов, каждый из которых назначен на пару частот. Каждое нажатие кнопки приводит к одновременной генерации двух синусоидальных тонов – одного из низкочастотной группы (от 697 до 941 Гц) и одного из высокочастотной группы (от 1209 до 1477 Гц).
Эта двухтональная система представляет собой прогресс в разработке пользовательского интерфейса и сложное применение технологии обработки сигналов. Фильтрация сигналов, как показано на примере тонального телефонного аппарата, использует комбинацию фильтров нижних частот (LP) и верхних частот (HP), за которыми следуют полосовые фильтры для распознавания отдельных тонов в пределах сгруппированных частот. Полосовые фильтры играют ключевую роль в обнаружении сигнала, пропуская только узкую полосу частот, эффективно изолируя тоны, производимые клавиатурой.}
В конструкции этих фильтров используется прецизионная электроника, и ее можно проиллюстрировать построением последовательной схемы RLC, которая работает как полосовой фильтр. Это резонансный контур, состоящий из резистора (R), катушки индуктивности (L) и конденсатора (C), который позволяет ему проходить избирательный диапазон частот, блокируя другие.
Система тонального набора служит примером практического применения конструкции электронного фильтра в реальных системах, демонстрируя критический характер выбора частоты и четкости сигнала в коммуникационных технологиях. Благодаря тщательно продуманной конструкции полосовых фильтров RLC телефоны с тональным набором могут надежно интерпретировать вводимые пользователем данные, тем самым сохраняя целостность информации, передаваемой по обширным сетям, соединяющим вызовы по всему миру.

Инженер проектирует схему для акустической системы с требуемой частотой кроссовера 2 кГц, учитывая сопротивление динамика в 8 Ом.
Тем...

Education

JoVE Core

Electrical Engineering

Электротехника

Unit 1

Раздел 1

Frequency Response

KEY TERMS AND CONCEPTS

ОСНОВНЫЕ ТЕРМИНЫ И ПОНЯТИЯ

touch-tone filter design example

Touch-tone telephony uses dual-tone multi-frequency (DTMF) signaling and a filter design example to show how keypad tones are separated. It replaced the old rotary dial with a matrix-style keypad arranged in four rows and three columns. Each of the 12 buttons produces a unique signal pair.

Every key press creates two sinusoidal tones at the same time. One tone comes from a low-frequency group between 697 and 941 Hz. The other comes from a high-frequency group between 1209 and 1477 Hz. This dual-tone method is a practical example of user interface design and signal processing in telecommunications.

The system also shows how filters can isolate signals. A combination of low-pass (LP) and high-pass (HP) filters helps separate the tone ranges. Bandpass filters then detect individual tones inside those grouped frequencies. A bandpass filter passes only a narrow range of frequencies, so it can isolate the keypad tones.

The filter itself can be built as a series RLC circuit. This resonant circuit uses a resistor (R), inductor (L), and capacitor (C) to pass a selective range of frequencies while blocking others. In touch-tone telephones, this kind of electronic filter design helps the system read user input clearly and keep communication signals accurate across phone networks.

Touch-Tone Filter Design Example

network function of a circuit

How Transfer Functions Shape Circuit Response

Transfer functions show how a circuit responds as signal frequency changes. They describe the link between input and output in frequency response analysis. This makes them useful for studying how circuits behave in electronics and engineering. A transfer function is a mathematical tool that relates phasor output to phasor input. It can be written as voltage gain, current gain, transfer impedance, or transfer admittance. The poles and zeros are the most important parts of the function. Zeros...

frequency response of a circuit

Inductive Circuit Frequency Response

Inductive circuit frequency response shows how a circuit with an inductor reacts to different frequencies. The analysis starts in the time domain and then moves into the frequency domain. In that step, the inductor is replaced by an impedance, and the circuit is written with phasors, which are sinusoidal signals shown with magnitude and phase. The transfer function describes how the output changes compared with the input at each frequency. A key parameter is the time constant, which is the...

gain

Circuit Gain and Phase Shift

Circuit gain and phase shift describe how a linear circuit changes a sinusoidal input voltage or current. These properties matter in circuits with reactive elements, because the response depends on the input frequency. As the frequency changes, the gain and phase shift also change. Gain compares the size of the output sinusoid to the size of the input sinusoid. If Vin is the input and Vout is the output, the gain K is the ratio of the output amplitude to the input amplitude. A gain greater...

bode plots

Reading Frequency Response on Bode Plots

Bode plots show how a circuit or system responds across frequency. They use a logarithmic frequency scale on the x-axis and gain in decibels on the y-axis. This format makes it easier to display a wide range of frequencies and to see how circuit parts affect behavior over that range. A network function gives the ratio of output to input for a system. Its complex form provides both magnitude and phase angle. The logarithmic gain on a Bode plot comes from the magnitude, calculated by multiplying...

transfer function and bode plots-i

Transfer Function Gain and Origin Effects

Transfer function gain and poles or zeros at the origin shape a system's Bode plot. The transfer function is often written in standard form after the polynomial coefficients are normalized. In that form, the constant gain, zeros, poles, and quadratic terms all appear clearly. The poles and zeros mark critical frequencies where the output magnitude and phase change noticeably. The constant gain K creates a fixed magnitude and phase term. Its magnitude is 20 log 10 K in decibels, and its phase...

transfer function and bode plots-ii

Bode Plot Slope and Phase Changes

Bode plots show how a transfer function changes with frequency. The standard form includes constant gain, poles and zeros at the origin, simple poles and zeros, and quadratic poles and zeros. Each part shapes the system response in a different way. A simple zero sets the magnitude trend first. The Bode magnitude plot stays flat at low frequencies, near 0 dB, and then rises at 20 dB per decade after the corner or break frequency, ω1. That corner frequency is where the straight-line...

bode plots construction

Reading Frequency Response with Bode Plots

Bode plots show the frequency response of a system with a magnitude plot and a phase plot. Both plots use a logarithmic frequency axis. In control system analysis, this makes it easier to see how a transfer function changes with frequency. To build a Bode plot, start with the transfer function H(ω). After normalization, the function includes constant gain, zeros, and poles. Each term affects the plot in a different way. A constant gain of 10 gives a starting magnitude of 20 dB, since 20...

series resonance

Series Resonance in RLC Circuits

Series resonance in an RLC circuit happens when the inductive reactance and capacitive reactance are equal. An RLC circuit contains a resistor, an inductor, and a capacitor. The impedance of the circuit is the ratio of the supply voltage to the circuit current. At resonance, the imaginary part of the impedance becomes zero. The frequency at which this occurs is called the resonant frequency. It depends on the inductance (L) and capacitance (C) of the circuit. Mathematically, the resonant...

characteristics of series resonant circuit

characteristics-of-series-resonant-circuit

Series Resonance and RLC Filter Behavior

Series resonance in an RLC circuit happens when the inductor, capacitor, and resistor are connected in series. At the resonant frequency, the inductive reactance and capacitive reactance are equal in size but opposite in sign, so they cancel each other. As a result, the circuit impedance becomes very small and is mainly set by the resistance. The resonant frequency of a series RLC circuit can be calculated from its inductance and capacitance. At this frequency, the current reaches its maximum...

parallel resonance

Parallel RLC Tuning at Resonance

A parallel RLC circuit uses a resistor, inductor, and capacitor connected to the same nodes. Because they share the same voltage, the circuit is analyzed with admittance, which describes how easily current can flow. In a parallel RLC circuit, admittance helps show how the circuit responds as the frequency changes. Resonance happens when the net reactance is zero. At that point, the capacitive and inductive effects cancel each other out. The resonant frequency is found from this condition. At...

frequency response of op amp circuits

Op Amp Gain and Bode Plot Basics

Operational amplifiers are used for signal conditioning, filtering, and mathematical tasks such as addition, subtraction, integration, and differentiation. Their frequency response shows how amplifier gain changes as the input frequency changes. This makes the gain of an op-amp a key idea in circuit design. At low frequencies, an op-amp can hold a constant gain called the dc gain, A0. As frequency rises, the gain starts to drop after the corner frequency, or break frequency, ω1. In other...

passive filters

Audio Frequency Control with Passive Filters

Passive filters shape the frequency spectrum of electrical signals. They use only passive parts such as resistors, inductors, and capacitors. Because they do not need an external power source, they can let selected frequency ranges pass or block others in many applications. Low-pass filters pass signals below the cutoff frequency, ωc, and reduce signals above it. In audio systems, they can send bass frequencies to woofers or subwoofers. For an RC low-pass filter, the transfer function H(s)...

active filters

Active Filter Design and Frequency Response

Active filters use op-amps, resistors, and capacitors to shape a signal's frequency response. They remove unwanted frequency components while keeping the parts of the signal that are needed. The design depends on the choice of resistor and capacitor values, which set the cutoff points and help define the overall response. A first-order low-pass active filter passes signals below a cutoff frequency and reduces signals above it. Its transfer function includes the low-frequency gain, also called...

scaling

Circuit Component Scaling for Filters

Circuit component scaling helps turn simple circuit values into practical ones for filter design and circuit analysis. Engineers often start with standard values like 1 ohm, 1 henry, or 1 farad because they make examples and problems easier to work through. Later, those values can be scaled to more realistic levels. This method is useful in filters, resonant circuits, and many other circuit analysis problems. It reduces calculation complexity while keeping the circuit behavior easy to study.

design example

Touch-tone telephony uses dual-tone multi-frequency (DTMF) signaling and a filter design example to show how keypad tones are separated. It replaced the old rotary dial with a matrix-style keypad arranged in four rows and three columns. Each of the 12 buttons produces a unique signal pair. Every key press creates two sinusoidal tones at the same time. One tone comes from a low-frequency group between 697 and 941 Hz. The other comes from a high-frequency group between 1209 and 1477 Hz. This...

key terms and concepts

Explore how touch-tone phones use DTMF signaling, LP and HP filters, and a series RLC bandpass circuit to detect keypad tones clearly.

Touch-Tone Filter Design Example | JoVE K12

JoVE Core Electrical Engineering offers easy-to-understand animated videos that cover fundamental concepts of electric circuits along with circuit analysis techniques. It incorporates first-order and second-order circuits using operational amplifiers and circuit transformation concepts. The inclusion of practical design examples and real-world applications through scientist-in-action videos adds significant educational value, making complex concepts accessible.

electrical engineering

HS-PS4-5

Travelling Waves

A wave is a disturbance that propagates from its source, repeating itself periodically, and is typically associated with simple harmonic motion. ...

Wave Parameters

The simplest mechanical waves are associated with simple harmonic motion and repeat themselves for several cycles. These simple harmonic waves can be ...

Equations of Wave Motion

Mathematically, the motion of a wave can be studied using a wavefunction. Consider a string oscillating up and down in simple harmonic motion, having a ...

Graphing the Wave Function

Consider the wave equation for a sinusoidal wave moving in the positive x-direction. The wave equation is a function of both position and time. From the ...

/files/media/science-education/science-education-thumbs/14721.jpg

Velocity and Acceleration of a Wave

A wave propagates through a medium with a constant speed, known as a wave velocity. It is different from the speed of the particles of the medium, which ...

Speed of a Transverse Wave

The speed of a wave depends on the characteristics of the medium. For example, in the case of a guitar, the strings vibrate to produce the sound. The ...

/files/media/science-education/science-education-thumbs/14722.jpg

Kinetic and Potential Energy of a Wave

All forms of waves carry energy; this is directly visualized in nature. For instance, the waves of earthquakes are so intense that they can shake huge ...

Energy and Power of a Wave

The total energy associated with a wavelength is the sum of the potential energy and the kinetic energy. The average rate of energy transfer associated ...

Propagation of Waves

When a wave propagates from one medium to another, part of it may get reflected in the first medium, and part of it may get transmitted to the second ...

Sound Waves

Sound waves can be thought of as fluctuations in the pressure of a medium through which they propagate. Since the pressure also makes the medium&#39;s ...

Sound as Pressure Waves

Sound waves, which are longitudinal waves, can be modeled as the displacement amplitude varying as a function of the spatial and temporal coordinates. As ...

/files/media/science-education/science-education-thumbs/14724.jpg

Speed of Sound in Solids and Liquids

Most solids and liquids are incompressible&#8212;their densities remain constant throughout. In the presence of an external force, the molecules tend to ...

Speed of Sound in Gases

The speed of sound in a gaseous medium depends on various factors. Since gases constitute molecules that are free to move, they are highly compressible. ...

Doppler Effect - I

The Doppler effect and Doppler shift were named after the Austrian physicist and mathematician Christian Johann Doppler in 1842, who conducted experiments ...

Doppler Effect - II

The Doppler effect has several practical, real-world applications. For instance, meteorologists use Doppler radars to interpret weather events based on ...

Shock Waves

While deriving the Doppler formula for the observed frequency of a sound wave, it is assumed that the speed of sound in the medium is greater than the ...

Echo

The human ear cannot distinguish between two sources of sound if they happen to reach within a specific time interval, typically 0.1 seconds apart. More ...

/files/media/science-education/science-education-thumbs/14729.jpg

Electromagnetic Waves

James Clerk Maxwell formulated a single theory combining all the electric and magnetic effects scientists knew during that time, calling the phenomena his ...

Generating Electromagnetic Radiations

The German physicist Heinrich Hertz (1857&#8211;1894) was the first to generate and detect certain types of electromagnetic waves in the laboratory. ...

Electromagnetic Wave Equation

Maxwell&#39;s equations for electromagnetic fields are related to source charges, either static or moving. These fields act on a test charge, whose ...

propagation-speed-of-electromagnetic-waves

Propagation Speed of Electromagnetic Waves

Electromagnetic waves are consistent with Ampere&#39;s law. Assuming there is no conduction current Ampere&#39;s law is given as:


Consider a plane ...

Electromagnetic Waves in Matter

Electromagnetic waves can travel in the vacuum as well as in matter. For example light, which is an electromagnetic wave, can travel through air, water, ...

Energy Carried By Electromagnetic Waves

Anyone who has used a microwave oven knows there is energy in electromagnetic waves. Sometimes, this energy is obvious, such as in the summer sun&#39;s ...

The Wave Nature of Light

The nature of light has been a subject of inquiry since antiquity. In the seventeenth century, Isaac Newton performed experiments with lenses and prisms ...

Use mathematical representations to support a claim regarding relationships among the frequency, wavelength, and speed of waves traveling in various media. [Clarification Statement: Examples of data could include electromagnetic radiation traveling in a vacuum and glass, sound waves traveling through air and water, and seismic waves traveling through the earth.] [Assessment Boundary: Assessment is limited to algebraic relationships and describing those relationships qualitatively.]

HS-PS4-1

The Electromagnetic Spectrum

Electromagnetic waves are categorized according to their wavelengths and frequencies, giving the electromagnetic spectrum. These waves are classified as ...

Classification of Signals

Signals are categorized as Continuous-time or discrete-time, Periodic or aperiodic, Analog or digital, and Causal or noncausal.
A continuous-time signal ...

Discrete Fourier Transform

Consider a vibration sensor that continuously captures data in the form of a continuous time-dependent signal.
However, in reality, the sensor can only ...

Discrete-Time Fourier Series

The Discrete-Time Fourier Series is a counterpart to the Fourier-series expansion of continuous-time periodic signals.
Calculating the expansion ...

Sampling Theorem

Consider the continuous-time signal x(t), and a train of impulses where Ts,&#xA0; is the sampling interval, and fs, is the sampling frequency.
Multiplying ...

Properties of Fourier Transform I

In radio broadcasting, Fourier Transform properties are applied in simultaneous multi-channel transmission, adjusting audio clip speeds, live broadcast ...

Signal and System

Signals are sets of data or information.
One-dimensional signals include single-variable functions, such as the variations in air pressure over time in ...

Methods of Documentation VII: EMR

Electronic Medical Records (EMRs) primarily center around electronically documenting patients&#39; health information within a single healthcare ...

Fast Fourier Transform

The Fast Fourier Transform, FFT, is a computational algorithm for calculating the Discrete Fourier Transform by breaking the calculations into smaller, ...

reconstruction-of-signal-using-interpolation

Reconstruction of Signal using Interpolation

Consider a continuous signal and its sampled counterpart with a sampling period T.
Applying a zero-order hold to the sampled signal results in a piecewise ...

Downsampling

Consider a sampled sequence with zero values between sampling instants. Replace it by taking every N-th value of the sampled sequence.
The original and ...

An engineer designs a circuit for a speaker system with a 2 kHz crossover frequency requirement, considering the speaker&#39;s resistance of 8 ohms.
The ...

Upsampling

Consider a decimated signal with a reduced frequency range due to its lower sampling rate.
Insert zeros between each sample to upsample, that introduces ...

Properties of DTFT I

Consider two discrete-time signals, each with their respective Discrete-Time Fourier Transforms DTFTs.
The signals are first multiplied by constants a and ...

Relation of DFT to z-Transform

The Discrete Fourier Transform (DFT) analyzes the frequency content of discrete-time signals.
It maps the N-sampled discrete time-domain sequence to its ...

Feedback control systems

Feedback control systems are categorized as linear or nonlinear, time-varying or time-invariant, and classified by signal types as continuous or ...

Properties of the z-Transform I

Certain properties provide a solid foundation for analyzing discrete-time systems using the Z-transform.
Considering two discrete-time signals, the ...

Magnetic Resonance Imaging

Magnetic resonance imaging (MRI) is a noninvasive medical imaging technique based on a phenomenon of nuclear physics discovered in the 1930s, in which ...

Evaluate questions about the advantages of using digital transmission and storage of information. [Clarification Statement: Examples of advantages could include that digital information is stable because it can be stored reliably in computer memory, transferred easily, and copied and shared rapidly. Disadvantages could include issues of easy deletion, security, and theft.]

Interference and Superposition of Waves

When two waves of the same nature occur in the same region simultaneously, they result in interference. Interference of waves implies that the net effect ...

Sound Waves: Interference

Sound waves can be modeled either as longitudinal waves, wherein the molecules of the medium oscillate around an equilibrium position, or as pressure ...

Interference: Path Lengths

Consider two sources of sound, that may or may not be in phase, emitting waves at a single frequency, and consider the frequencies to be the same.
Two ...

/files/media/science-education/science-education-thumbs/14727.jpg

concept-of-resonance-and-its-characteristics

Concept of Resonance and its Characteristics

If a driven oscillator needs to resonate at a specific frequency, then very light damping is required. An example of light damping includes playing piano ...

/files/media/science-education/science-education-thumbs/12772.jpg

Sound Waves: Resonance

Resonance is produced depending on the boundary conditions imposed on a wave. Resonance can be produced in a string under tension with symmetrical ...

Reflection of Waves

When a wave travels from one medium to another, it gets reflected at the boundary of the second medium. A common example of this is when a person yells at ...

Standing Waves

Sometimes waves do not seem to move; rather, they just vibrate in place. Unmoving waves can be seen on the surface of a glass of milk kept in a ...

/files/media/science-education/science-education-thumbs/12783.jpg

Modes of Standing Waves - I

A close look at earthquakes provides evidence for the conditions appropriate for resonance, standing waves, and constructive and destructive interference. ...

/files/media/science-education/science-education-thumbs/12784.jpg

Modes of Standing Waves: II

The starting point for expressing the modes of standing waves is understanding the boundary conditions that the waves must follow. The boundary conditions ...

/files/media/science-education/science-education-thumbs/14723.jpg

Beats

The study of music provides many examples of the superposition of waves and the constructive and destructive interference that occurs. Very few examples ...

/files/media/science-education/science-education-thumbs/14728.jpg

Interference and Diffraction

Source: Yong P. Chen, PhD, Department of Physics &#38; Astronomy, College of Science, Purdue University, West Lafayette, IN
Interference and diffraction ...

Reflection and Refraction

Source: Derek Wilson,&#160;Asantha Cooray, PhD, Department of Physics &#38; Astronomy, School of Physical Sciences, University of California, Irvine, CA
...

Electromagnetic Fields

Electric fields generated by static charges, often referred to as electrostatic fields, are characteristically different from electric fields created by ...

Photoelectric Effect

Source: Yong P. Chen, PhD, Department of Physics &#38;&#38; Astronomy, College of Science, Purdue University, West Lafayette, IN
Photoelectric effect ...

Evaluate the claims, evidence, and reasoning behind the idea that electromagnetic radiation can be described either by a wave model or a particle model, and that for some situations one model is more useful than the other. [Clarification Statement: Emphasis is on how the experimental evidence supports the claim and how a theory is generally modified in light of new evidence. Examples of a phenomenon could include resonance, interference, diffraction, and photoelectric effect.] [Assessment Boundary: Assessment does not include using quantum theory.]

HS-PS4-3

Touch-Tone Filter Design Example

Description

Transcript

Tags

More videos by Standards