Name: stopping white salt crystals on masonry
Uploaded: 2024-09-12T16:16:29.000Z
Duration: 1 min 25 s
Channel: JoVE

Efflorescence appears as a crystalline powder patch, often white in color, on brick, stone, or concrete masonry surfaces.
When water infiltrates the masonry surface, water-soluble alkaline salts present in the masonry units or mortar dissolve in water.
Eventually, this water migrates to the surface and evaporates, leaving behind deposits of salts on the masonry surface.
Efflorescence that occurs soon after the completion of construction can be cleaned off using water and a brush.
Although efflorescence might reappear again, natural agents like rain can wash away the salt deposits, and with time, efflorescence reduces as the salts gradually leach out of the masonry.
Efflorescence appearing on the masonry walls of a building after several years indicates that water has recently started to penetrate the wall.
Rectifying the source of leakage will control further occurrences of efflorescence.
To prevent efflorescence, masonry units and mortar free of water-soluble salts are used, and water intrusion into the masonry walls is minimized.
The walls can be sheltered by providing proper roof drainage or applying waterproof barriers that prevent the entry of external moisture yet permit the outward migration of water vapor.

efflorescence in masonry

Efflorescence in masonry walls appears as a fluffy crystalline powder, often white, resulting from water-soluble salts within the masonry or mortar. When water penetrates the masonry, it dissolves these salts and brings them to the surface, where they are deposited upon evaporation of water.
While initial efflorescence is common post-construction and can be cleaned with water and a brush, in certain instances, efflorescence can reappear and gradually diminish over time as salts are leached out from the masonry surfaces when exposed to natural agents such as rain. However, efflorescence appearing on masonry surfaces in the later years of completion of construction indicates new water leaks. In such cases, the source of the water leak must be identified and repaired.
Efflorescence can be prevented by using masonry units tested for the absence of soluble salts and employing clean mortar ingredients. Minimizing the water intrusion into the masonry surfaces also reduces efflorescence. This is done by ensuring adequate roof drainage and providing sheltering roof overhangs wherever feasible. Also, applying coatings on the wall that prevent moisture ingress without impeding the outward movement of water vapor prevents efflorescence. In some cases, cavity wall construction may be preferable to solid wall construction, providing an additional barrier against moisture intrusion.

Efflorescence in Masonry

Efflorescence appears as a crystalline powder patch, often white in color, on brick, stone, or concrete masonry surfaces.
When water infiltrates the ...

Education

JoVE Core

Civil Engineering

Unit 1

Masonry

KEY TERMS AND CONCEPTS

stopping white salt crystals on masonry

Efflorescence is the white, fluffy crystal layer that can form on masonry walls. It happens when water-soluble salts in brick, stone, concrete, or mortar are dissolved by water and carried to the surface. When the water evaporates, the salts are left behind as a powdery deposit.

New efflorescence is often seen soon after construction. In many cases, it can be cleaned with water and a brush. It may also fade over time as rain leaches salts out of the masonry surface. If efflorescence appears years after a building is finished, it often points to a new water leak that should be found and repaired.

Efflorescence can be reduced by choosing masonry units that have been tested for low soluble salts and by using clean mortar ingredients. Limiting water intrusion also helps. Good roof drainage, roof overhangs where possible, and wall coatings that block moisture but still let water vapor escape can all lower the risk. In some buildings, cavity wall construction gives extra protection against moisture compared with solid wall construction.

Stopping White Salt Crystals on Masonry

composite masonry walls

Bonding and Materials in Composite Masonry

Composite masonry walls use two or more wythes, or vertical layers, of masonry to form one unified wall. The wythes may use the same material or different masonry materials. They are joined to work together as a single structure. These wythes can be bonded in several ways. Builders may use mortar-filled collar joints, grouted spaces, or rigid metal ties with reinforcement. Masonry header units can also connect the layers, but this method is rare. Metal ties are often preferred because they...

masonry cavity walls

Masonry Cavity Walls and Moisture Control

Masonry cavity walls use two wythes, or layers, with a hollow space between them. The outer and inner wythes are linked only by corrosion-resistant metal ties. This design helps manage water and improve wall performance. When rainwater passes through the outer wythe, it moves down through the cavity. Flashing catches the water and directs it toward weep holes, where it can leave the wall. The inner wythe often has damp-proofing on the cavity side. This layer also works as an air barrier. The...

masonry loadbearing walls

How Masonry Walls Support Buildings

Masonry load-bearing walls support floors and roofs and carry those loads down to the foundation. They are built from brick, stone, or concrete masonry units. These walls rely on compressive strength, which means they can resist pushes from above very well. Masonry walls may be reinforced or unreinforced, depending on the building needs. They carry dead loads and live loads while using working stresses that stay below the materials' ultimate strength. That safety margin helps the structure...

masonry curtain walls

Masonry Curtain Walls and Support Systems

Masonry curtain walls use brick or stone veneer as an exterior cladding system. The veneer is supported by the building structure, so the wall can be both attractive and functional. Two main construction methods are used for these walls. One method builds the masonry units in place through traditional layering. The other uses prefabricated panels that are assembled on the ground and then lifted into position. In traditional construction, steel shelf angles attached to the spandrel beam carry...

posttensioned masonry walls

How Masonry Walls Gain Extra Strength

Post-tensioned masonry walls gain extra strength from high-strength steel rods or flexible tendons. These tensioning elements are anchored to the foundation and run vertically through the wall. In some walls, they sit inside the cores of the masonry units. In others, they are placed between the masonry wythes, or layers. The wall is built first with the tensioning elements already in place. After the mortar cures fully, the wall is tightened. Steel rods are tensioned by turning nuts against...

cavity drainage and flashings in masonry walls

cavity-drainage-and-flashings-in-masonry-walls

Moisture Control in Masonry Cavity Walls

Masonry cavity walls use a gap between two wythes, or wall layers, to help control moisture. The cavity is usually at least 2 inches wide, and it may contain insulation. Even with insulation, a clear space of at least 1 inch is kept so water can drain away. Some walls also use a continuous drainage mat to reduce the needed space while still moving moisture out. Weep holes are another key part of cavity drainage. These openings sit at the base of the cavity and let collected water escape. They...

thermal insulation in masonry walls

Masonry Wall Insulation Options

Masonry wall insulation can be placed on the outside, inside the wall, or on the interior surface. The best choice depends on the climate, the building design, and whether the wall is being built new or retrofitted. In hot, dry climates, masonry can help smooth indoor temperatures by absorbing heat during the day and releasing it at night. In many other climates, extra insulation is needed to improve thermal resistance. One common exterior method is an Exterior Insulation and Finish System, or...

expansion and contraction in masonry walls

expansion-and-contraction-in-masonry-walls

Masonry Wall Joints for Temperature and Moisture

Masonry walls change size slightly as temperature and moisture change. Builders account for this movement so the wall does not crack or shift out of place. Thermal movement is usually easy to measure and plan for. Moisture movement is harder to predict. New clay masonry units often absorb water and expand over time in normal outdoor conditions. New concrete masonry units behave differently. They usually shrink as they lose extra moisture gained during production. These opposite changes make...

movement joints in buildings

How Buildings Handle Structural Movement

Buildings are designed to handle movement from temperature changes, moisture changes, and structural deflection. If these changes are ignored, they can cause visible damage or even unsafe conditions. Movement joints give building materials room to move without creating distress. Working joints are the simplest type. They are placed during construction and help materials cope with change as the building goes up. Shingled roofs and wood bevel siding are common examples because they can move with...

types of building separation joints

Building Joints for Movement and Stability

Building separation joints help large or complex buildings move in a controlled way. They split a structure into smaller, separate units. This reduces stress when the building shifts under different forces. The joints are grouped into three main types: volume-change joints, settlement joints, and seismic separation joints. Volume-change joints handle expansion and contraction caused by temperature changes and moisture changes. They are placed where the building mass has discontinuities,...

Efflorescence is the white, fluffy crystal layer that can form on masonry walls. It happens when water-soluble salts in brick, stone, concrete, or mortar are dissolved by water and carried to the surface. When the water evaporates, the salts are left behind as a powdery deposit. New efflorescence is often seen soon after construction. In many cases, it can be cleaned with water and a brush. It may also fade over time as rain leaches salts out of the masonry surface. If efflorescence appears...

mortar joint deterioration in masonry

Repairing Damaged Mortar Joints in Masonry

Mortar joints in masonry can break down when water collects in them and freezes. The repeated freezing and thawing makes the water expand and shrink. That process creates cracks in the joints and can spread damage over time. As the mortar worsens, pieces may spall, or break off from the joint surface. Loose masonry units can follow, and the wall becomes weaker. Damaged joints also let moisture move into the wall, which adds to the problem. Good construction helps protect mortar joints. Using...

masonry in cold and hot weather conditions

masonry-in-cold-and-hot-weather-conditions

Protecting Mortar During Weather Changes

Masonry work changes in cold and hot weather because mortar must stay at the right temperature and moisture level. If mortar freezes before it cures, its strength and watertightness can drop. For proper hydration and curing, mortar should stay between 60°F and 80°F. When the weather is below 40°F, the water used for mortar must be heated. The water should not exceed 120°F, because very hot water can reduce compressive strength and bond strength. Masonry units and sand should also stay dry and...

masonry paving

Masonry Paving Materials and Base Layers

Masonry paving uses bricks, stones, and concrete masonry units to create durable walking and driving surfaces. These materials are selected for their shape, color, strength, and resistance to abrasion and weathering. Masonry units can be used in different paving setups depending on the site and the load they must carry. Some paving systems are installed dry on a thin sand layer over a gravel base. Others are set in mortar or asphalt on a concrete slab. For areas with heavy vehicular loads, a...

key terms and concepts

Learn why white salt crystals form on masonry walls, how to clean early efflorescence, and how to prevent it with better drainage and moisture control.

Stopping White Salt Crystals on Masonry | JoVE K12

JoVE Core Civil Engineering offers a foundational exploration of essential construction materials such as bricks, stones, steel, wood, and concrete, along with fluid mechanics topics like flow over immersed bodies, open channel flow, and dimensional modeling. It also covers key surveying concepts, including leveling, traverse adjustments, curve design, topographic mapping, and geospatial technologies (GPS & GIS). Science-in-action videos showcase laboratory research on materials, fluids, and surveying practices in real-world engineering systems.

civil engineering

Stopping White Salt Crystals on Masonry

Description

Transcript

Tags