Name: wood structure and uses in building
Uploaded: 2024-09-12T16:16:32.000Z
Duration: 1 min 19 s
Channel: JoVE

Trees, the source of wood, have a trunk enveloped by a shielding layer of dead bark.
Under the dead outer bark is living bark. Next is the cambium, then the thick sapwood, which becomes heartwood as it ages. The pith is at the core of the trunk.
The tree&#39;s age can be determined by counting the concentric bands called growth rings in a tree&#39;s trunk.
Elongated, tubular cells aligned with the trunk&#39;s length define the wood&#39;s grain. Wood can take a greater load in the direction of grains than in the direction perpendicular to the grains.
Wood is procured from trees in the form of long cylindrical logs, which are transported to the mills for cutting.
The logs are usually cut into boards and slabs in the mills and seasoned before use.
Wood, particularly in the form of lumber and timber, is one of the most familiar construction materials.
Doors, windows, flooring, columns, beams, and stair railings are constructed using wood.
Additionally, wood is used to manufacture plywood, particleboard, and hardboard.

introduction to wood

Wood, derived from trees, is a versatile and widely used construction material. Trees feature a trunk surrounded by a protective layer of dead bark. Beneath this outer layer lies the living bark, followed by the cambium, and then the sapwood which transitions into heartwood as it matures. At the center of the trunk is the pith. The age of a tree can be discerned by examining its growth rings, which are concentric bands visible in the trunk&#39;s cross-section.
The structural integrity of the wood is influenced by its grain&#8212;elongated, tubular cells aligned with the trunk&#39;s length, allowing it to bear greater loads along the grain direction compared to perpendicular to the grains.
Wood is available in the form of large cylindrical logs and transported to mills where it is transformed into boards and slabs. Before being used in construction, wood is typically seasoned to reduce moisture content and enhance durability.
Wood is used as lumber or timber in construction and is integral to building various structural elements and fixtures including doors, windows, flooring, roofing, columns, beams, and stair railings. It is also used in making furniture and scaffolding. Beyond solid wood, it serves as a base material for manufacturing plywood, particleboard, and hardboard.

Introduction to Wood

Trees, the source of wood, have a trunk enveloped by a shielding layer of dead bark.
Under the dead outer bark is living bark. Next is the cambium, then ...

Education

JoVE Core

Civil Engineering

Unit 1

Wood

KEY TERMS AND CONCEPTS

wood structure and uses in building

Wood is a construction material made from trees. A tree trunk has several layers. The outside is a protective layer of dead bark. Under that is living bark, then the cambium, then sapwood. As sapwood matures, it becomes heartwood. The pith sits at the center of the trunk.

The age of a tree can be read from its growth rings. These rings are concentric bands seen in a trunk cross-section. Wood strength also depends on grain. Grain refers to elongated, tubular cells that run along the length of the trunk. Wood can carry greater loads along the grain than across it.

Wood is usually cut as large cylindrical logs and sent to mills. There, it is turned into boards and slabs. Before construction use, wood is often seasoned. Seasoning lowers moisture content and helps improve durability.

In building, wood is used as lumber or timber. It is important for doors, windows, flooring, roofing, columns, beams, and stair railings. It is also used to make furniture and scaffolding. Wood is also a base material for plywood, particleboard, and hardboard.

Wood Structure and Uses in Building

Wood is a construction material made from trees. A tree trunk has several layers. The outside is a protective layer of dead bark. Under that is living bark, then the cambium, then sapwood. As sapwood matures, it becomes heartwood. The pith sits at the center of the trunk. The age of a tree can be read from its growth rings. These rings are concentric bands seen in a trunk cross-section. Wood strength also depends on grain. Grain refers to elongated, tubular cells that run along the length of...

softwoods and hardwoods

Wood Grain in Softwoods and Hardwoods

Softwoods and hardwoods come from different kinds of trees, and their leaf structures and cell makeup help explain how they are used. Softwoods come from cone-bearing trees with needle-like leaves. Hardwoods usually come from trees that shed broad leaves seasonally. Softwoods are made mostly of long cells called tracheids and a smaller number of rays, which are radial cells. This simpler structure gives softwoods a rougher grain. Because of this, they are often used in construction for...

lumber

Lumber Cutting Methods

Lumber is made from logs that are harvested, debarked, and processed into long pieces with a rectangular cross-section. The process starts when an automated saw slices a log into slabs. Those slabs then move on a conveyor belt to smaller saws, where they are cut into square-edged pieces of specific widths. Freshly cut lumber usually has rough surfaces. Its dimensions may also vary slightly from one end to the other. The way wood is cut affects both the lumber’s appearance and how it is used. <br...

structural properties and dimensions of lumber

structural-properties-and-dimensions-of-lumber

Wood Strength Tests and Lumber Sizes

Wood strength depends on how its fibers are aligned along the length of the tree. This alignment gives wood much greater tensile strength along the grain than across it, sometimes up to twenty times higher. Wood also tends to perform better under compression than under tension. Fiber length varies by wood type. Hardwoods have fibers about one twenty-fifth of an inch long. Softwoods have longer fibers that range from one-eighth to one-third of an inch. Laboratory tests help measure how wood...

seasoning of wood

Wood Drying for Stronger Construction

Seasoning of wood is the drying process used to lower and stabilize moisture content before wood is used in construction. Fresh wood can swell when it takes in moisture and contract as it dries. Seasoning helps reduce that movement so the wood stays more stable after it is built into a structure. The main goal is to reach equilibrium moisture content. This is the point where the wood’s moisture level matches the moisture in the surrounding environment. When wood is seasoned properly, it is...

wood surfacing

Wood Surfacing for Smooth, Safe Lumber

Wood surfacing smooths lumber, improves its size accuracy, and makes it safer to handle. It is a key finishing step in woodworking and construction. The process also helps correct small distortions that can form as wood dries. Before surfacing, the wood may be sized slightly larger to account for shrinkage during seasoning, which is the drying stage. A plane, a tool with rotating blades, is used to remove material and smooth the surface. The same tool can also round the edges a little, which...

lumber defects

Common Wood Flaws in Lumber

Lumber defects are flaws in wood that can change both its appearance and its strength. These defects come from tree growth and from the way lumber is processed. Knowing the main defects helps explain why some boards are better for construction and manufacturing than others. Some defects begin in the tree itself. Knots form where branches were once attached to the trunk, and knotholes appear when those knots fall out. Decay and insect damage are also natural defects that can weaken wood and...

wood fasteners

Wood Fastener Types and Uses

Wood fasteners connect parts of a wood structure and help keep members in place. The strength of the connection depends mainly on direct bearing between the wood members. Different fasteners are chosen for different jobs and structural needs. Nails are the most common wood fasteners. They are sharp-pointed metal pins that are driven into wood with a hammer or a mechanical nail gun. Nails come in many diameters, head styles, and lengths. Nailing methods also matter. Face nailing places the...

veneer

How Veneer Is Cut and Used

Veneer is a thin sheet of wood that is usually about one-eighth of an inch thick or less. It is made to show the look of wood while using timber more efficiently. Veneer is common in furniture and other finished wood products. One common way to make veneer is rotary cutting. In this method, a log is mounted in a large lathe and spun against a knife edge. As the knife moves deeper into the turning log, it peels off a continuous strip of wood. This creates rotary-cut veneer. Other veneer...

wood products

Engineered Wood Products in Construction

Engineered wood products are made from wood strands, veneers, lumber, and even waste wood shreds. They are used in both structural and nonstructural building applications. These materials are designed to improve strength, durability, and versatility in modern construction. Glue-laminated wood, or glulam, is made by bonding several smaller pieces of dimensional lumber with adhesive. Cross-laminated timber uses solid lumber panels with layers placed so the grain direction alternates. This layer...

wood panel products

Types of Wood Panels in Construction

Wood panels are common construction materials used for flooring, siding, and roofing. They usually come in standard 4-foot by 8-foot sheets. Their thickness can range from one-quarter of an inch to one and one-eighth inches. Plywood is one of the most familiar wood panels. It is made by gluing thin wood veneers, or layers, under pressure. The outer veneer grain runs lengthwise, while the inner layers run widthwise. Plywood also has an odd number of layers, which helps keep the panel...

key terms and concepts

Explore how tree layers, growth rings, grain, and seasoning affect wood. Learn how logs become lumber used in buildings, furniture, and panels.

Wood Structure and Uses in Building | JoVE K12

JoVE Core Civil Engineering offers a foundational exploration of essential construction materials such as bricks, stones, steel, wood, and concrete, along with fluid mechanics topics like flow over immersed bodies, open channel flow, and dimensional modeling. It also covers key surveying concepts, including leveling, traverse adjustments, curve design, topographic mapping, and geospatial technologies (GPS & GIS). Science-in-action videos showcase laboratory research on materials, fluids, and surveying practices in real-world engineering systems.

civil engineering

Wood Structure and Uses in Building

Description

Transcript

Tags