Name: reducing power loss in three-phase lines
Uploaded: 2024-07-08T13:19:58.000Z
Duration: 1 min 10 s
Channel: JoVE

Zaman alanında temsil edilen ve faz başına eşdeğer bir devreye dönüştürülebilen dengeli bir üç telli Y-Y devresini düşünün.
İlk olarak, hat akımı belirlenir, ardından yükteki faz voltajı belirlenir.
Daha sonra kaynak tarafından iletilen güç, sinüzoidal faz gerilimi ve hat akımının etkin değerleri kullanılarak belirlenir.
Daha sonra, yüke verilen güç, hat akımı ve yük direnci kullanılarak hesaplanır.
Hatta kaybedilen güç, hat akımı ve hat direnci kullanılarak elde edilir.
Daha sonra üç fazlı kaynağın sağladığı toplam güç, üç fazlı yükün aldığı toplam güç ve hatlarda kaybedilen toplam güç belirlenir.
Hatta, hat akımını en aza indirerek azaltılabilen yüksek bir güç yüzdesi kaybolur.
Ancak bu, yük akımını azaltacak ve bu da yüke verilen gücü azaltacaktır.
Yük akımını etkilemeden hat akımını azaltmanın bir yolu, üç fazlı devreye transformatörler eklemektir.

İletim hattındaki kayıp

Kaynak yük bağlantılarının farklı konfigürasyonları yıldız (Y) ve üçgen (Δ) bağlantılarını içerir. Hat ve faz gerilimleri ile akımları arasındaki ilişki konfigürasyona bağlı olarak değişir. Kaynak güç sağladığında teller aracılığıyla yüke iletilir ve bu iletim sırasında gücün bir kısmı teller tarafından emilerek güç kaybına neden olur.
Hat kaybı, dengeli bir üç fazlı devrede güç dağıtım verimliliğini etkiler. Böyle bir devredeki simetri, yalnızca bir fazı dikkate almamıza izin vererek analizi basitleştirir. Faz başına eşdeğer devre, hat kaybı da dahil olmak üzere çeşitli parametrelerin hesaplanmasına yardımcı olur.
Güç Kaybının Hesaplanması:
Yükün her fazına iletilen güç, faz akımının karesi ile faz yük direncinin çarpımıdır.
Hat Kaybı Hesabı:
Her bir tel için hat kaybı, hat akımının büyüklüğünün karesi alınarak ve bunun hattın direnciyle çarpılmasıyla hesaplanır.
Dengeli üç fazlı sistemler için bu hesaplama, toplam güç kaybını bulmak için üçle (her faz için bir tane) çarpılır. Hattın direnci, malzemenin direnci ve hattın uzunluğu ile doğru orantılı, iletkenin kesit alanı ile ters orantılıdır. Bu, hat kaybının iletkenin uzunluğuyla doğru orantılı, iletkenin kesit alanıyla ters orantılı olduğu anlamına gelir. Enerji şirketleri, hat kayıplarını en aza indirmek ve gücü daha yüksek voltajlarda iletmek için daha büyük kesit alanına sahip iletkenler kullanır; bu, aynı miktarda güç için daha düşük akıma olanak tanır. Bunun nedeni, gücün voltaj ve akımın ürünü olması ve belirli bir güç seviyesi için voltajın arttırılması, akımın azalmasına izin vererek hat kayıplarını azaltmasıdır.

İletim Hattındaki Kayıp

Zaman alanında temsil edilen ve faz başına eşdeğer bir devreye dönüştürülebilen dengeli bir üç telli Y-Y devresini düşünün.
İlk olarak, ...

Education

JoVE Core

Electrical Engineering

Elektrik Mühendisliği

Unit 1

Ünite 1

Three-Phase Circuits

Üç Fazlı Devreler

KEY TERMS AND CONCEPTS

TEMEL TERİMLER VE KAVRAMLAR

Line Loss

reducing power loss in three-phase lines

Three-phase power lines can lose energy as electricity travels from the source to the load. This line loss affects how efficiently power reaches the load. In balanced three-phase circuits, the symmetry makes the analysis easier because one phase can represent the whole system.

The source-load connection can use wye, also called star, or delta configurations. These setups change the relationship between line voltage, phase voltage, line current, and phase current. A per-phase equivalent circuit helps calculate the power delivered to the load and the power lost in the lines.

For each phase of the load, the delivered power depends on the square of the phase current and the phase load resistance. The power lost in one wire is found from the square of the line current multiplied by the resistance of that line. For a balanced three-phase system, the total line loss is three times the loss in one phase.

Line resistance depends on the material resistivity, the length of the conductor, and its cross-sectional area. As the line gets longer, resistance and line loss increase. A larger cross-sectional area lowers resistance and helps reduce loss. Power companies use larger conductors and higher transmission voltages to keep current lower for the same power level, which reduces line loss.

Reducing Power Loss in Three-Phase Lines

three-phase circuits

How Three-Phase Power Delivers Electricity

Three-phase power is a major part of AC power distribution, especially where steady and efficient electricity delivery is needed. AC systems are grouped into single-phase, two-phase, and three-phase systems. These categories help describe how power moves from the source to the load. Single-phase circuits are common in homes. They usually use a two-wire system that connects one AC source to loads. These circuits can supply everyday appliances such as lamps, televisions, and microwaves at 120 V...

generation of three-phase voltage

Three-Phase AC Generator Windings

A three-phase AC generator uses rotating magnet windings and a stationary stator to make three-phase voltage. The rotor carries a magnet that spins inside the stator. The stator holds the three-phase winding, and mutual induction creates the voltage. The stator windings are spread evenly around the inside of the stator. They are placed 120 electrical degrees apart. These windings consist of three separate coils, or groups of coils, called phases. The phases can be connected in a Y, or star,...

three-phase voltages

Three-Phase Power Connections

Three-phase power connections use balanced voltages that are equal in magnitude and separated by 120 degrees. A three-phase generator produces these voltages, and the balance helps reduce power loss while keeping energy delivery steady to connected loads. Three-phase sources can be arranged in either wye or delta form. The loads connected to the system can also use wye or delta. This flexibility gives control over how the system is designed and managed. In a wye connection, one end of each...

the y-to-y circuit

Balanced Wye-to-Wye Neutral Current

A balanced wye-to-wye circuit uses three wye-connected sinusoidal voltage sources and three wye-connected loads. A neutral wire links the neutral node of the source to the neutral node of the load. The load impedance is connected across each phase of the load. The source and load can be connected in either a four-wire or a three-wire arrangement. A three-phase system is balanced when each phase has the same load. In that case, the current flow and phase angle are uniform across the system. If...

the y-to-delta circuit

Wye Source and Delta Load Currents

A balanced wye source and delta load form a common three-phase circuit with no neutral line connection. The source is Y-connected, and the load is delta-connected. To analyze the circuit, the first step is to assume a positive phase sequence. These phase voltages are then used to find the line voltages that appear across the delta load impedances. In the wye source, the phase voltages are V an, V bn, and V cn. In the delta load, the line voltages are V ab, V bc, and V ca. These line voltages...

the delta-to-delta circuit

Balanced Delta-Delta Power Circuit

A balanced delta-delta power circuit uses a delta-connected source and a delta-connected load. The two deltas form a closed loop that creates three separate phases. In this setup, the phase voltages are the same as the line voltages. If the source is in positive sequence, the phase voltages can be written directly, and no neutral wire is needed. The delta-connected load current is found by dividing the phase voltage by the impedance of each phase. For line current, Kirchhoff’s Current Law...

the delta-to-y circuit

Delta-Wye Source and Load Connections

A balanced delta-wye circuit connects a delta-connected source to a wye-connected load. In this setup, the phase voltage of the delta source equals the line voltage of the wye load. The source also sets the line currents that flow into the load. For a balanced system, the phase difference between currents makes it possible to find one line current from the other by using the positive sequence of phases. In the wye-connected load, each phase current equals the line current from the delta source.

power in a three-phase circuit

Balanced Three-Phase Power Calculation

Balanced three-phase power calculation depends on the wye and delta connections used in the circuit. A wye, or star, configuration can use three wires or four wires. A delta configuration connects the components in a closed loop. These connection types change how voltages and currents are arranged, but both are used in three-phase systems. In a balanced three-phase system, instantaneous power is the power at one exact moment. Even though the power in each phase changes over time, the total...

power distribution in three-phase and single phase circuits

power-distribution-in-three-phase-and-single-phase-circuits

Single-Phase vs. Three-Phase Power Loss

Single-phase and three-phase circuits distribute electrical power in different ways. Single-phase power is common in homes, while balanced three-phase power is widely used in industrial settings with heavy machinery. Both systems deliver energy, but their current flow and wire needs are not the same. A single-phase circuit usually uses a two-wire system. The current depends on the power absorbed by the load and the line voltage. Because wire loss from resistance follows the square of the...

line loss

Three-phase power lines can lose energy as electricity travels from the source to the load. This line loss affects how efficiently power reaches the load. In balanced three-phase circuits, the symmetry makes the analysis easier because one phase can represent the whole system. The source-load connection can use wye, also called star, or delta configurations. These setups change the relationship between line voltage, phase voltage, line current, and phase current. A per-phase equivalent circuit...

reducing line loss

Cutting Heat Loss in Three-Phase Lines

Three-phase power systems can lose energy as heat in transmission lines because the wires have resistance. This line loss becomes important when electricity travels over a distance. A common solution is to use transformers to change the voltage and current in the system. The setup uses two three-phase transformers. A step-up transformer is placed at the source, and a step-down transformer is placed at the load. Raising the voltage at the source lowers the current in the transmission lines, and...

key terms and concepts

Learn how balanced three-phase circuits, wye and delta connections, and conductor size affect line loss, power delivery, and transmission efficiency.

Reducing Power Loss in Three-Phase Lines | JoVE K12

JoVE Core Elektrik Mühendisliği, devre analizi teknikleriyle birlikte elektrik devrelerinin temel kavramlarını kapsayan, anlaşılması kolay animasyonlu videolar sunar. Operasyonel amplifikatörler ve devre dönüşümü kavramlarını kullanarak birinci dereceden ve ikinci dereceden devreleri içerir. Pratik tasarım örneklerinin ve gerçek dünya uygulamalarının bilim insanlarınca hazırlanan videolar aracılığıyla dahil edilmesi, karmaşık kavramları erişilebilir hale getirerek önemli bir eğitim değeri katmaktadır.

electrical engineering

Reducing Power Loss in Three-Phase Lines

Description

Transcript

Tags