Name: stress components on a cube at a point
Uploaded: 2024-03-07T13:22:33.000Z
Duration: 1 min 23 s
Channel: JoVE

Çoklu yüklemeye maruz kalan bir cismin gerilme bileşenleri, O noktasında merkezlenmiş küçük bir küp dikkate alınarak analiz edilir.
Küp, karşılık gelen eksenlere dik yüzlere etki eden normal ve kesme gerilimi bileşenlerine sahiptir.
Gizli yüzler de görünen yüzlerdekine eşit ve zıt olan bu stresleri yaşarlar. Böylece denge korunur.
Küpün yüzeylerindeki gerilmeler O noktasındakilerden biraz farklı olsa da, küpün kenar uzunluğu sıfıra düştüğünde bu küçük hata ortadan kalkar.
Küpün serbest cisim diyagramı göz önüne alındığında, yüzlere etki eden normal ve kesme kuvvetleri, karşılık gelen gerilim bileşenlerinin her bir yüzün alanı ile çarpılmasıyla belirlenir.
Daha sonra, denge denklemleri uygulanarak, kesme gerilimi bileşenleri arasındaki ilişkiler türetilir, bu da belirli bir noktada gerilim koşulunu tanımlamak için yalnızca altı gerilim bileşeninin gerekli olduğu anlamına gelir.
Ayrıca, kayma gerilimi sadece bir düzlemde meydana gelemez. Bu nedenle, ona dik olan başka bir düzleme eşit bir kesme gerilimi uygulanmalıdır.

stresin bileşenleri

Çoklu yükleme koşulları altında stres analizi karmaşıktır ve normal ve kayma gerilmelerinin kapsamlı bir şekilde anlaşılmasını gerektirir. O noktasında, görünen veya görünmeyen altı yüzün tamamında gerilime maruz kalan küçük bir küp düşünün. Normal gerilim bileşenleri σ_x, σ_y, σ_z x, y ve z eksenlerine dik etki eder. τ_xy ve τ_xz kesme gerilimi bileşenleri bu eksenlere dik yüzeylere uygulanır.


 İlginçtir ki, gizli küp yüzleri de görünür yüzlerdekilere eşit ve zıt bu gerilimleri deneyimleyerek dengeyi sağlar. Küpün kenar uzunluğu sıfıra yaklaştıkça, O'daki gerilimler ile küpün yüzlerindeki gerilimler arasındaki fark ihmal edilebilir hale gelir.


 Küp üzerine etki eden kuvvetlerin incelenmesi, kayma gerilimi bileşenleri arasında önemli ilişkilere yol açar: τ_xy eşittir τ_yx, τ_yz eşittir τ_zy ve τ_zx eşittir τ_xz; bu da bir noktadaki gerilim durumunu dokuz değil yalnızca altı gerilim bileşeninin tanımladığını gösterir.


 Daha da önemlisi, kesme yalnızca tek bir düzlemde meydana gelemez. Birinciye dik olan başka bir düzleme eşit bir kayma gerilimi uygulanmalıdır. Son olarak, yorumlanan gerilim durumu, dikkate alınan elemanın oryantasyonuna bağlı olarak değişebilir, bu da çoklu yükleme koşulları altında gerilim analizinin karmaşıklığını vurgular.

Stresin Bileşenleri

Çoklu yüklemeye maruz kalan bir cismin gerilme bileşenleri, O noktasında merkezlenmiş küçük bir küp dikkate alınarak analiz edilir.
Küp normal ve ...

Education

JoVE Core

Mechanical Engineering

Makine Mühendisliği

Unit 1

Ünite 1

Concept of Stress

Stres Kavramı

KEY TERMS AND CONCEPTS

TEMEL TERİMLER VE KAVRAMLAR

Components of Stress

stress components on a cube at a point

Stress components on a small cube help describe how a body behaves under multiple loading. The cube is centered at point O and has stress acting on all six faces, whether the faces are visible or hidden. Normal stress components σx, σy, and σz act perpendicular to the x, y, and z axes. Shearing stress components also act on the cube faces.

The visible faces carry shear stresses such as τxy and τxz. The hidden faces carry equal and opposite stresses. This balance keeps the cube in equilibrium. As the side length of the cube becomes very small, the difference between the stress at point O and the stress on the cube faces becomes negligible.

Looking at the forces on the cube also shows key links between shear components. The shear stresses satisfy τxy = τyx, τyz = τzy, and τzx = τxz. Because of these relations, only six stress components are needed to define the stress condition at a point, not nine. Shear cannot act in only one plane. An equal shearing stress must also act on a perpendicular plane.

The stress picture can change when the cube is rotated. That means the interpreted stress state depends on the orientation of the element being studied. This makes stress analysis under multiple loading conditions more complex.

Stress Components on a Cube at a Point

normal stress

Normal Stress in Axial Loading

Normal stress acts perpendicular to a material’s cross-sectional area. It appears when a force is applied along the axis of an object, which is called axial loading. Bridge truss members are a practical example of this kind of loading. When a rod carries axial load, internal forces develop across the section. Because these forces act normal to the plane of the section, the stress is called normal stress. Stress here means the average stress over the whole cross-section, not the value at one...

shearing stress

Shear Forces in Bolts and Rivets

Shearing stress is caused by transverse forces acting on an object. These forces create internal forces in the plane where the external forces are applied. The total internal force in that section is called the shear. Average shearing stress is found by dividing the shear by the cross-sectional area. This value is only an average, because shear stress is not spread evenly across the section. It can be zero at the surface and much higher than the average in other areas. Bolts, pins, and rivets...

bearing stress

Bolt-to-Plate Contact Pressure

Bearing stress is the contact pressure between two separate bodies. A common example is a bolt pushed through a plate. The bolt applies a force to the plate, and the plate pushes back with an equal and opposite force. That force is not a single point load. It is made up of many smaller forces spread across the contact surface between the bolt and the plate. Because these microforces are complex, engineers use an average value called bearing stress. Bearing stress is found by dividing the...

applications of stress

Boom and Rod Stress Analysis

Boom and rod stress analysis shows how a pinned support structure carries a load. The boom and the rod are connected by a pin and held in place by brackets and pins. The structure is then separated from its supports so the forces can be studied clearly. A free-body diagram is drawn to identify every force on the boom, the rod, and the load. The reaction forces on both members are found using equilibrium equations. At point P, the reaction causes compression in the boom. At point R, the...

stress on an oblique plane

Axial Load Stress on Inclined Sections

Axial loading creates stress in a material along its central axis. This kind of load can cause compression or elongation, and it produces normal stress. Normal stress acts perpendicular to the material area and can be either tensile or compressive. When the section is not perpendicular to the load, it becomes an oblique plane. On this inclined plane, the stress state includes both normal stress and shearing stress. Shearing stress acts parallel to the area and changes shape without changing...

stress: general loading conditions

Stress Components on a Loaded Body

Stress components on a loaded body can be found by cutting the body through a point with a plane parallel to the xy plane. That section carries the original loads, along with normal forces and shearing forces. The result is a simple way to describe how a structure responds under combined loading. The shearing force in the section can point in different directions within the plane. It is split into two parts that run parallel to the x and y axes. Each part is divided by the area, and as that...

components of stress

Stress components on a small cube help describe how a body behaves under multiple loading. The cube is centered at point O and has stress acting on all six faces, whether the faces are visible or hidden. Normal stress components σx, σy, and σz act perpendicular to the x, y, and z axes. Shearing stress components also act on the cube faces. The visible faces carry shear stresses such as τxy and τxz. The hidden faces carry equal and opposite stresses. This balance keeps the cube in equilibrium.

design consideration

Safety Factors in Structural Design

Safety factors in structural design help engineers choose a material and loading limit that can be used safely. The process begins with a material’s ultimate strength. This value comes from tests that increase force until the material reaches its breaking point or limit. The ultimate load is then divided by the original cross-sectional area to find the ultimate normal stress, or strength. Ultimate shearing stress is another key value used in design. These limits show how much stress a material...

key terms and concepts

Learn how normal and shearing stresses act on a small cube at a point, why only six stress components are needed, and how orientation changes stress analysis.

Stress Components on a Cube at a Point | JoVE K12

JoVE Core Makine Mühendisliği, denge, kuvvetler, kafes kiriş analizi ve yapısal mekanik gibi temel konuları kapsayan kısa, anlaşılması kolay animasyonlu videolar sunar. Gerçek dünyadaki uygulamalarını keşfedin ve bilim insanlarının önderlik ettiği deneylerle bu kavramların uygulanmasına tanık olun.

mechanical engineering

Stress Components on a Cube at a Point

Description

Transcript

Tags