Name: principal strain directions in 3d
Uploaded: 2024-05-23T12:59:55.000Z
Duration: 1 min 29 s
Channel: JoVE

Üç boyutlu gerinim analizi, elastik, homojen malzemelerdeki deformasyonu değerlendirmek için temel gerilme eksenlerini kullanır.
Küçük bir kübik eleman, bu eksenler etrafında genişletildiğinde, deformasyonu gösteren dikdörtgen bir paralel yüzlüye dönüşür.
Gerinim analizi, bir elemanın n ekseni gibi bir ana eksen etrafında döndürülmesini ve bu eksene dik yüzlerdeki gerinim bileşenlerinin değerlendirilmesini içerir. Bu yöntem, düzlem gerinim dönüşümüne dayanmaktadır.
Mohr çemberi kullanılarak, küp ana eksenler etrafında dönerken gerinim dönüşümü incelenir. Bu yaklaşım, üç dairenin en büyüğünün çapına eşdeğer olan belirli bir noktadaki maksimum kesme gerilmesini tanımlar.
Düzlem gerinimde, n ekseni, Mohr'un daire diyagramının kökeninde sıfır gerinim ile bir ana eksene dönüşür. Bu orijinin zıt taraflarındaki ana suşlar, maksimum ve minimum normal suşları temsil eder.
Düzlem gerilimi yaşayan yapıların ince plakalarında, n ekseni bir asal gerilim eksenine dönüşür.
N ekseni boyunca ana gerinim, düzlem içi gerinimlerle ilişkilidir. M ekseni etrafındaki dönüş, maksimum kesme gerilimini tanımlar.

gerinimin Üç boyutlu analizi

Three-Dimensional Analysis of Strain

Üç boyutlu gerinim analizi, özellikle elastik ve homojen malzemelerde malzemelerin gerilim altında nasıl deforme olduğunu anlamak için çok önemlidir. Bu yöntem, karmaşık gerilim durumlarını daha anlaşılır formlara basitleştirmek için temel gerilim eksenlerini kullanır. Malzeme içindeki küçük bir kübik eleman, gerilime maruz kaldığında bu eksenler boyunca genişler veya büzülür ve dikdörtgen bir paralel yüzeye dönüşür. Bu dönüşüm, malzemenin deformasyonunu etkili bir şekilde göstermektedir. Asal gerilim eksenleri dik olup, gerilimin malzeme içinde kaymaya neden olmadığı yönleri temsil eder.

Mohr dairesi gerinim analizinde önemli bir araçtır. Bir noktadaki gerilim durumlarının grafiksel bir temsilini sağlar ve eleman n ekseni gibi bir asal eksen etrafında döndüğünde gerinim bileşenlerini değerlendirir. Bu analiz, n ekseninin başlangıcındaki gerinimlerin sıfır olduğu düzlem gerinim dönüşümlerine odaklanır ve Mohr dairesinin karşıt taraflarında gösterilen maksimum ve minimum gerinimlerin belirlenmesini basitleştirir.

Düzlem gerilim altındaki ince plakalar gibi senaryolarda, n ekseni asal gerilim ekseni haline gelir. Burada, n ekseni boyunca asal gerinim, malzemenin düzlem içi gerinimleri ile doğrudan ilişkilidir. M ekseni gibi başka bir asal eksen etrafındaki dönüş, yük altındaki malzeme davranışını tahmin etmek ve yapısal tasarımların güvenliğini ve güvenilirliğini sağlamak için çok önemli olan maksimum kesme geriliminin konumlarını ve büyüklüklerini belirlemeye yardımcı olur.

Gerinimin Üç Boyutlu Analizi

Üç boyutlu gerinim analizi, elastik, homojen malzemelerdeki deformasyonu değerlendirmek için temel gerilme eksenlerini kullanır.
Küçük bir kübik element, ne zaman ...

Education

JoVE Core

Mechanical Engineering

Makine Mühendisliği

Unit 1

Ünite 1

Transformations of Stress and Strain

Gerilme ve Şekil Değiştirme Dönüşümleri

KEY TERMS AND CONCEPTS

TEMEL TERİMLER VE KAVRAMLAR

principal strain directions in 3d

Three-dimensional strain analysis shows how a material changes shape when it is loaded. It is especially useful for elastic, homogeneous materials. A small cubic element inside the material can expand or contract along principal stress axes. That change turns the cube into a rectangular parallelepiped, which makes the deformation easier to picture.

The principal stress axes are orthogonal, or at right angles to each other. Along these directions, the stress does not create shear inside the material. This simplifies a complex stress state into a form that is easier to analyze and compare.

Mohr's circle is a key graph used in strain analysis. It shows the stress state at a point and helps evaluate strain components as the element rotates about a principal axis, such as the n-axis. In plane strain transformations, the strain at the origin of the n-axis is zero. This makes it easier to find the maximum and minimum strains, which appear on opposite sides of Mohr's circle.

For thin plates under plane stress, the n-axis becomes a principal stress axis. In that case, the principal strain along the n-axis is directly related to the in-plane strains of the material. Rotation about another principal axis, such as the m-axis, helps locate the maximum shearing strain and its magnitude. These results are important for predicting how materials behave under load and for supporting safe, reliable structural design.

Principal Strain Directions in 3D

transformation of plane stress

Plane Stress Changes with Rotation

Plane stress changes with rotation in a material element. The analysis looks at a prismatic element inside a cube under plane stress. As the element turns, the normal stress and shearing stress on its faces change in both size and direction. These changes are described with trigonometric functions of the rotation angle. The forces on the rotated faces are compared with the forces on the original faces that are perpendicular to each principal axis. The equilibrium equations use only the forces...

principal stresses

Stress Circle for Principal and Shear Stress

The stress circle shows how normal stress and shearing stress change with angle on a transformed plane. Its center, C, lies on the vertical axis and represents the average normal stress. The radius shows the amount of stress variation as the plane rotates. Points A and B, where the circle crosses the horizontal axis, mark the maximum and minimum normal stresses. At these points, shearing stress is zero. These points define the principal stress planes, where only normal stress, called principal...

principal stresses: problem solving

Finding Principal Planes and Stress Limits

Principal planes and principal stresses are found by analyzing two planes that meet at right angles under shearing, tensile, and compressive stresses. The goal is to use the given stress values to describe how the material is loaded and to locate the planes where the stress state changes. To find the principal planes, use the formula that relates the plane angle to twice the shearing stress divided by the difference between tensile and compressive stresses. After substituting the known stress...

mohr&#39;s circle for plane stress

Reading Stress Components with Mohr's Circle

Mohr's circle is a graphical way to read the stress state at a point in a material under plane stress. It turns normal stress and shearing stress into a two-dimensional picture. This makes stress transformation easier to analyze. The method uses Cartesian coordinates. The horizontal axis shows normal stress, written as σ, and the vertical axis shows shearing stress, written as τ. Two points, A and B, are plotted from the stresses on the element. Point A is at (σx, -τxy), and point B is at (σx,...

general state of stress

Stress Tensor and Principal Stresses

The stress tensor describes the internal forces inside a material. It is used when a material is under external force or deformation. At a point such as O, the tensor can show the stress components on any plane through that point. A tetrahedral element helps show how these forces act. One face, XYZ, is perpendicular to the line OA. The other faces line up with the coordinate axes, and point O is the origin. The stress on the tetrahedron is split into normal and shear components on each face. <br...

yield criteria for ductile materials under plane stress

yield-criteria-for-ductile-materials-under-plane-stress

Tresca and Von Mises Yield Criteria

Ductile materials can yield when they are loaded beyond a safe stress level. Engineers use yield criteria to check whether structural elements and machine parts can handle the expected load without permanent deformation. The yield point is first found with a tensile test, which measures how the material responds to uniaxial stress. A tensile test is not enough when a part faces biaxial or plane stress conditions. In those cases, more advanced criteria are needed to predict failure. One common...

transformation of plane strain

Plane Strain Under Rotated Axes

Plane strain changes when the coordinate axes are rotated. This matters for long bars and similar elongated structures that are loaded uniformly on their sides. In these members, one dimension is much larger than the others, so deformation is mainly studied in a single plane. At a point such as O, the key strain components lie along the x and y axes. The strain along the z-axis is negligible in plane strain. Together, the x and y strain components describe the deformation state in the xy-plane.

mohr&#39;s circle for plane strain

Principal and Shear Strains on Mohr’s Circle

Mohr’s circle for plane strain shows how normal strain and shear strain change on a graph. The horizontal axis is normal strain, written as ε, and the vertical axis is shear strain, written as γ. It uses two plotted points, X and Y, to represent the strain state. Point X has coordinates (εx, -γXY), and point Y has coordinates (εY, γXY). The center of the circle, O, gives the average normal strain. The radius comes from the relationship between normal strain and shear strain, so the circle...

three-dimensional analysis of strain

Three-dimensional strain analysis shows how a material changes shape when it is loaded. It is especially useful for elastic, homogeneous materials. A small cubic element inside the material can expand or contract along principal stress axes. That change turns the cube into a rectangular parallelepiped, which makes the deformation easier to picture. The principal stress axes are orthogonal, or at right angles to each other. Along these directions, the stress does not create shear inside the...

measurements of strain

How Strain Gauges Measure Deformation

Strain describes how a material deforms when a force is applied. Normal strain compares the change in length with the original length. Engineers use this measure to track stretching or compression in materials. For higher accuracy, they often use electrical strain gauges. A strain gauge has a conductive wire on a paper backing that sticks to the surface of the material. It works through the piezoresistive effect, which means the wire’s electrical resistance changes when the material is bent,...

key terms and concepts

Learn how principal stress axes, Mohr's circle, and plane stress help show 3D strain, including maximum, minimum, and shearing strain in materials.

Principal Strain Directions in 3D | JoVE K12

JoVE Core Makine Mühendisliği, denge, kuvvetler, kafes kiriş analizi ve yapısal mekanik gibi temel konuları kapsayan kısa, anlaşılması kolay animasyonlu videolar sunar. Gerçek dünyadaki uygulamalarını keşfedin ve bilim insanlarının önderlik ettiği deneylerle bu kavramların uygulanmasına tanık olun.

mechanical engineering

Principal Strain Directions in 3D

Description

Transcript

Tags