Name: measuring elements by atomic fluorescence
Uploaded: 2024-12-05T18:32:16.000Z
Duration: 1 min 29 s
Channel: JoVE

في التحليل الطيفي الفلوري الذري ، أو AFS ، يتم تشعيع العينات المتناثرة بواسطة الإشعاع الكهرومغناطيسي لإحداث تحولات إلكترونية ، ويتم قياس الإشعاع الفلوري المنبعث.
تحتوي أداة AFS على مصدر ضوء عالي الكثافة ، ورذاذ ، ومحدد طول موجي ، وكاشف. تشمل مصادر الإثارة المحتملة مصابيح الكاثود المجوفة النبضية ، ومصابيح التفريغ الكهربائي ، ومصابيح قوس الزينون أو الزئبق ، والليزر.
كما هو الحال في AAS ، يتم تفتيت المادة التحليلية ثم إثارتها بواسطة مصدر الضوء. تطلق الذرات المثارة الطاقة عن طريق التألق بأطوال موجية تمثل أنواعا ذرية معينة للعودة إلى حالات الطاقة المنخفضة.
نظرا لأن الذرات تتألق عند طولها الموجي الأمثل للامتصاص ، فإن شعاع المصدر يكون بزاوية قائمة للكاشف - عادة ما يكون أنبوب مضاعف ضوئي.
تتناسب شدة التألق مع تركيز العنصر المستهدف. كما أنه يتناسب مع شدة التشعيع ، مما يجعل المصادر عالية الكثافة والحد الأدنى من الإشعاع المتداخل ضرورية.
ومع ذلك، فإن AFS فعال بشكل خاص في تحديد العناصر المكونة للهيدريد المتطاير والزئبق.
علاوة على ذلك ، يمكن تجنب التداخلات الكيميائية والطيفية من الانحلال عن طريق إضافة عوامل إطلاق أو حماية إلى المصفوفة.

التحليل الطيفي بالفلورسنت الذري

Atomic Fluorescence Spectroscopy

<div style="direction:rtl">
 التحليل الطيفي بالفلورسنت الذري (AFS) هو تقنية تحليلية تعتمد على الانتقالات الإلكترونية للذرات في اللهب أو الفرن أو البلازما التي يتم إثارتها بواسطة الإشعاع الكهرومغناطيسي (EM). عندما تمتص هذه الذرات الطاقة، تصبح مثارة وبالتالي تطلق الطاقة أثناء عودتها إلى حالتها الأصلية. يتم رصد هذا الضوء المنبعث، أو "الفلورسنت"، بزاوية قائمة على الشعاع الساقط. تحدث كل من عمليتي الامتصاص والانبعاث عند أطوال موجية مميزة، وهي سمة للأنواع الذرية المحددة الموجودة. يعد التحليل الطيفي بالفلورسنت الذري مفيدًا بشكل خاص لتحديد الزئبق (Hg) والعناصر الأخرى التي تشكل الهيدريدات المتطايرة، مثل الزرنيخ (As) والسيلينيوم (Se).
 تتضمن الأجهزة المطلوبة لقياسات الفلورسنت الذري مصدر ضوء عالي الكثافة، وجهاز تذرية، ومحدد طول موجي، وكاشف. في حين أن المصدر المتصل سيكون مرغوبًا فيه، إلا أنه نادرًا ما يستخدم بسبب خرج الطاقة المنخفض. بدلاً من ذلك، تُستخدم مصابيح الكاثود المجوفة النبضية، ومصابيح التفريغ بدون أقطاب، ومصابيح قوس الزينون أو الزئبق، والليزر كمصادر ضوء محتملة.
 تتناسب شدة إشارة الفلورسنت مع تركيز العنصر المستهدف وشدة الإشعاع، مما يجعل المصادر عالية الكثافة والإشعاع المتداخل الأدنى ضروريًا. يمكن إدخال مواد كيميائية مختلفة، مثل عوامل التحرير والحماية، في المصفوفة لتقليل التداخلات الكيميائية والطيفية التي تنشأ أثناء التذرية.
</div>

التحليل الطيفي الفلوري الذري (AFS) هو تقنية تحليلية تتضمن التحولات الإلكترونية للذرات في اللهب أو الفرن أو البلازما ...

Education

JoVE Core

Analytical Chemistry

الكيمياء التحليلية

Unit 1

الوحدة الأولى

Atomic Spectroscopy

المطيافية الذرية

KEY TERMS AND CONCEPTS

المصطلحات والمفاهيم الأساسية

measuring elements by atomic fluorescence

Atomic fluorescence spectroscopy measures elements by detecting the light atoms give off after they are excited by electromagnetic radiation. The atoms are first placed in a flame, furnace, or plasma. They absorb energy, become excited, and then release that energy as they return to their original state. The emitted light is called fluorescence.

The fluorescence is observed at a right angle to the incoming beam. This setup helps separate the emitted light from the light used to excite the atoms. The absorption and emission steps occur at distinct wavelengths. Those wavelengths are characteristic of the atomic species present.

Atomic fluorescence spectroscopy is especially useful for measuring mercury (Hg). It also works well for elements that form volatile hydrides, including arsenic (As) and selenium (Se). The instrument uses a high-intensity light source, an atomizer, a wavelength selector, and a detector.

A continuum source would be useful, but it is rarely used because its power output is low. Instead, pulsed hollow-cathode lamps, electrodeless-discharge lamps, xenon or mercury arc lamps, and lasers can serve as light sources. The fluorescence signal increases with the target element's concentration and the irradiation intensity. For that reason, strong light sources and low interfering radiation are important.

Chemical and spectral interferences can appear during atomization. To reduce them, releasing agents and protective agents can be added to the matrix. These chemicals help improve the measurement when the sample contains substances that might interfere with the signal.

Measuring Elements by Atomic Fluorescence

measuring-elements-by-atomic-fluorescence

atomic spectroscopy: absorption, emission, and fluorescence

atomic-spectroscopy-absorption-emission-and-fluorescence

Element Analysis with Atomic Light Spectra

Atomic spectroscopy is used to identify and measure elements by their light signals. It supports both qualitative analysis, which tells what is present, and quantitative analysis, which tells how much is present. The optical methods in this group are atomic absorption spectroscopy, atomic emission spectroscopy, and atomic fluorescence spectroscopy. These methods begin with atomization. In this step, a solid, liquid, or solution sample is changed into gas-phase atoms and ions. Once the sample...

atomic spectroscopy: effects of temperature

atomic-spectroscopy-effects-of-temperature

How Heat Changes Atomic Spectra

Heat changes atomic spectra by affecting atomization, excitation, ionization, and line shape. In atomic spectroscopy, atomization means converting a sample into gas-phase atoms and ions. The flame temperature needed for this step changes how efficiently the method works and shifts the balance between excited and ground-state atoms. At thermal equilibrium, the relative numbers of excited and ground-state atoms can be estimated with the Maxwell-Boltzmann distribution. A small temperature rise...

atomic absorption spectroscopy: overview

Atomic Absorption Spectroscopy for Trace Metals

Atomic absorption spectroscopy (AAS) measures trace metals by tracking how atoms absorb electromagnetic radiation (EMR). The absorbed light makes atoms move to a higher-energy orbit. In AAS, the key step is atomization, which converts the sample into gas-phase atoms. A flame or a furnace is typically used for this step. Inside the flame, some atoms become thermally excited. Most stay in the ground state, which is the lowest-energy state. These ground-state gas-phase atoms absorb EMR only when...

atomic absorption spectroscopy: instrumentation

atomic-absorption-spectroscopy-instrumentation

Atomic Absorption Spectroscopy: Key Parts

Atomic absorption spectrophotometry uses a set of key parts to measure light absorbed by atoms. The main components are a radiation source, an atomizer, a monochromator, and a detector. Each part has a specific job in the instrument. The radiation source is usually a hollow-cathode lamp, or HCL, or an electrodeless-discharge lamp, or EDL. Both produce a narrow emission line at the needed wavelength. Some instruments instead use continuum sources with high-resolution monochromators to narrow...

atomic absorption spectroscopy: radiation and light sources

atomic-absorption-spectroscopy-radiation-and-light-sources

Choosing Light Sources for AAS Measurements

Atomic absorption spectroscopy (AAS) uses a light source that emits a very narrow range of wavelengths. This is needed because the source must match the absorption behavior of the analyte atom. The choice of source also depends on giving a precise, intense emission at the right wavelength for accurate detection. Two common line sources in AAS are hollow-cathode lamps (HCLs) and electrodeless-discharge lamps (EDLs). These lamps are selected based on the element being analyzed and the level of...

atomic absorption spectroscopy: atomization methods

atomic-absorption-spectroscopy-atomization-methods

Atomic Absorption Spectroscopy: Sample Atomization

Atomic absorption spectroscopy uses sample atomization to turn a liquid specimen into free atoms for analysis. The two main approaches are flame atomization and electrothermal atomization. Both methods prepare the sample so its atoms can be measured by the instrument. Flame atomization uses a nebulizer and spray chamber to mix the sample with a fuel-oxidant mixture. This creates a fine aerosol mist that enters the burner. The fuel and oxidant are usually close to a stoichiometric ratio, but a...

atomic absorption spectroscopy: interference

atomic-absorption-spectroscopy-interference

Correcting Errors in Atomic Absorption Spectroscopy

Atomic absorption spectroscopy interference can create systematic error by making the analytical signal or the background look stronger or weaker than it should be. In atomic absorption measurements, these errors are usually grouped as spectral interference, chemical interference, and physical interference. Spectral interference happens when signals from other elements or molecules overlap with the analyte signal, the substance being measured. This overlap can falsely raise or hide the analyte...

atomic absorption spectroscopy: lab

AAS Sample Prep and Calibration

Atomic absorption spectroscopy (AAS) depends on careful sample preparation and calibration. Samples must be turned into clear solutions before measurement. That often means extra treatment to dissolve materials such as soils, animal tissues, and minerals. Common sample prep methods include hot mineral acids, wet ashing, combustion in closed containers, high-temperature ashing, and fusion with reagents. These steps help make the sample suitable for AAS analysis. Solutions that contain organic...

atomic emission spectroscopy: overview

Atomic Emission Spectroscopy for Element Analysis

Atomic emission spectroscopy is used to identify the elements in a sample by measuring the light they emit. Atoms are first excited to higher energy levels by thermal energy from hot sources such as plasma, arcs, or sparks. When they fall back to lower energy levels, they give off light at specific wavelengths. Each element produces its own set of lines, so the emission spectrum can show both what is present and how much is there. AES instruments are similar to atomic absorption spectrometers,...

atomic emission spectroscopy: instrumentation

atomic-emission-spectroscopy-instrumentation

AES Sample Handling and Detection

Atomic emission spectrometry (AES) uses sample handling, atomization, and detection parts to measure emitted light from atoms and ions. The sample must first be changed into a gas-phase form so it can produce a measurable signal. AES uses two main atomizer types. Continuous atomizers, such as flames and plasmas, feed the sample in a steady stream. Discrete atomizers add one sample at a time with syringes or autosamplers. The electrothermal atomizer is the most common discrete type. Many...

atomic emission spectroscopy: interference

atomic-emission-spectroscopy-interference

Reducing Interference in AES Signals

Atomic emission spectroscopy (AES) can produce interfering signals when atoms and molecules in a flame or plasma emit overlapping light. High-temperature atomizers excite many species at once, including oxides, hydroxides, and flame combustion products. These extra emissions can make the analyte signal harder to read. Spectral interference happens when emission lines or bands overlap. One way to reduce it is to improve instrument resolution. Another is to choose a different emission line for...

inductively coupled plasma atomic emission spectroscopy: principle

inductively-coupled-plasma-atomic-emission-spectroscopy-principle

ICP-AES Torch and Sample Analysis

Inductively coupled plasma atomic emission spectroscopy uses a plasma torch to analyze elements in a sample. This method is also called inductively coupled plasma optical emission spectroscopy, or ICP-OES. It is widely used because the plasma creates a strong environment for elemental analysis. The ICP source, or torch, contains three concentric quartz tubes. Argon gas flows through the tubes. A spark from a Tesla coil starts the ionization of argon and creates a high-temperature plasma. The...

inductively coupled plasma atomic emission spectroscopy: instrumentation

inductively-coupled-plasma-atomic-emission-spectroscopy

ICP-AES Instrument Types and Detection

Inductively coupled plasma atomic emission spectroscopy, or ICP-AES, uses an inductively coupled plasma to detect and analyze elements in a sample. The method measures the light given off by atoms, which helps identify and compare different elements. It is a common approach in atomic emission spectroscopy. ICP-AES instruments are built in three main forms: sequential, simultaneous multichannel, and Fourier transform instruments. Fourier transform designs are less commonly used, but they are...

atomic emission spectroscopy: lab

Plasma Sources in Atomic Emission Spectroscopy

Atomic emission spectroscopy uses plasma sources to identify elements by their light. The method creates abundant spectra with characteristic emission lines. Inductively coupled plasma, or ICP, is especially useful because it gives strong quantitative data. It works well under stable conditions, with low noise, low background, and few interferences. Newer air-operated microwave sources are also being studied. These sources may be more cost-effective than conventional ICP systems. Atomic...

atomic fluorescence spectroscopy

Atomic fluorescence spectroscopy measures elements by detecting the light atoms give off after they are excited by electromagnetic radiation. The atoms are first placed in a flame, furnace, or plasma. They absorb energy, become excited, and then release that energy as they return to their original state. The emitted light is called fluorescence. The fluorescence is observed at a right angle to the incoming beam. This setup helps separate the emitted light from the light used to excite the...

flame photometry: overview

Flame Emission Spectrometry Basics

Flame emission spectrometry uses a flame to excite elements in a sample so their light can be measured. It is also called flame photometry. The method can be used for both qualitative and quantitative analysis of elements. The idea became established in the early 1860s when Kirchhoff and Bunsen showed that specific elements give off characteristic radiation in a flame. The first instrument for this purpose measured sodium in plant ash with a Bunsen flame. A major problem was how to add the...

flame photometry: lab

Flame Photometry and Metal Detection

Flame photometry is a method for detecting metals by measuring the light they emit in a flame. A solution such as potassium chloride is aspirated into the flame. The solvent evaporates first. The remaining salt becomes dehydrated and then dissociates into free gaseous atoms in the ground state. Some of these atoms absorb energy from the flame and move to an excited state. When they return to the ground state, they emit photons at characteristic wavelengths. These emissions are very narrow...

key terms and concepts

Measure mercury, arsenic, and selenium with atomic fluorescence spectroscopy. Learn how excited atoms emit fluorescence and how instruments detect it.

Measuring Elements by Atomic Fluorescence | JoVE K12

analytical chemistry

JoVE Core Analytical Chemistry simplifies complex chemical principles by breaking them down into clear, engaging animations, making topics from SI Units to NMR spectroscopy more accessible and straightforward. Additionally, the scientist-in-action videos highlight the application of these concepts in real-world research conducted in laboratories globally.

Measuring Elements by Atomic Fluorescence

Description

Transcript