transport-of-surface-modified-carbon-nanotubes-through-a-soil-column

Transport of Surface-modified Carbon Nanotubes through a Soil Column

Carbon nanotubes (CNTs) are widely manufactured nanoparticles, which are being utilized in a number of consumer products, such as sporting goods, ...

Uppsala University

The effect of particle concentration, size distribution (polydispersity) and magnetic attractive forces (Fe(0) content) on agglomeration and transport of poly(styrene sulfonate) (PSS) modified NZVI was studied in water-saturated sand (d(p) = 300 microm) columns. Particle concentrations ranged from 0.03 to 6 g/L in 5 mM NaCl/5 mM NaHCO3 at a pore water velocity of 3.2 x 10(-4) m/s. Three NZVI dispersions with different intrinsic particle size distributions obtained from sequential sedimentation are compared. The influence of magnetic attraction (Fe(0) content) on NZVI agglomeration and deposition in porous media is assessed by comparing the deposition behavior of PSS-modified NZVI (magnetic) having different Fe(0) contents with PSS-modified hematite (nonmagnetic) with the same surface modifier. At low particle concentration (30 mg/L) all particles were mobile in sand columns regardless of size or magnetic attractive forces. At high concentration (1 to 6 g/L), deposition of the relatively monodisperse dispersion containing PSS-modified NZVI (hydrodynamic radius (R(H)) = 24 nm) with the lowest Fe(0) content (4 wt%) is low (attachment efficiency (alpha) = 2.5 x 10(-3)), insensitive to particle concentration, and similar to PSS-modified hematite. At 1 to 6 g/L, the attachment efficiency of polydisperse dispersions containing both primary particles and sintered aggregates (R(H) from 15 to 260 nm) of PSS-modified NZVI with a range of Fe(0) content (10-60%) is greater (alpha = 1.2 x 10(-2) to 7.2 x 10(-2) and is sensitive to particle size distribution. The greater attachment for larger, more polydisperse Fe(0) nanoparticles with higher Fe(0) content is a result of their agglomeration during transport in porous media because the magnetic attractive force between particles increases with the sixth power of particle/agglomerate radius. A filtration model that considers agglomeration in porous media and subsequent deposition explains the observed transport of polydisperse PSS-modified NZVI at high concentration.

Particle size distribution, concentration, and magnetic attraction affect transport of polymer-modified Fe(0) nanoparticles in sand columns.

Controlled emplacement of polyelectrolyte-modified nanoscale zerovalent iron (NZVI) particles at high particle concentration (1-10 g/L) is needed for effective in situ subsurface remediation using NZVI. Deep bed filtration theory cannot be used to estimate the transport and deposition of concentrated polyelectrolyte-modified NZVI dispersions (>0.03 g/L) because particles agglomerate during transport which violates a fundamental assumption of the theory. Here we develop two empirical correlations for estimating the deposition and transport of concentrated polyelectrolyte-modified NZVI dispersions in saturated porous media when NZVI agglomeration in porous media is assumed to reach steady state quickly. The first correlation determines the apparent stable agglomerate size formed during NZVI transport in porous media for a fixed hydrogeochemical condition. The second correlation estimates the attachment efficiency (sticking coefficient) of the stable agglomerates. Both correlations are described using dimensionless numbers derived from parameters affecting deposition and agglomeration in porous media. The exponents for the dimensionless numbers are determined from statistical analysis of breakthrough data for polyelectrolyte-modified NZVI dispersions collected in laboratory scale column experiments for a range of ionic strength (1, 10, and 50mM Na(+) and 0.25, 1, and 1.25 mM Ca(2+)), approach velocity (0.8 to 55 × 10(-4)m/s), average collector sizes (d(50)=99 μm, 300 μm, and 880 μm), and polyelectrolyte surface modifier properties. Attachment efficiency depended on approach velocity and was inversely related to collector size, which is contrary to that predicted from classic filtration models. High ionic strength, the presence of divalent cations, lower extended adsorbed polyelectrolyte layer thickness, decreased approach velocity, and a larger collector size promoted NZVI agglomeration and deposition and thus limited its mobility in porous media. These effects are captured quantitatively in the two correlations developed. The application and limitations of using the correlations for preliminary design of in situ NZVI emplacement strategies is discussed.

Empirical correlations to estimate agglomerate size and deposition during injection of a polyelectrolyte-modified Fe0 nanoparticle at high particle concentration in saturated sand.

Polymer-modified nanoscale zerovalent iron (NZVI) particles are delivered into porous media for in situ remediation of nonaqueous phase liquid (NAPL) source zones. A systematic and quantitative evaluation of NAPL targeting by polymer-modified NZVI in two-dimensional (2-D) porous media under field-relevant conditions has not been reported. This work evaluated the importance of NZVI particle concentration, NAPL saturation, and injection strategy on the ability of polymer-modified NZVI (MRNIP2) to target the NAPL/water interface in situ in a 2-D porous media model. Dodecane was used as a NAPL model compound for this first demonstration of source zone targeting in 2-D. A driving force for NAPL targeting, the surface activity of MRNIP2 at the NAPL/water interface was verified ex situ by its ability to emulsify NAPL in water. MRNIP2 at low particle concentration (0.5 g/L) did not accumulate in or near entrapped NAPL, however, MRNIP2 at moderate and high particle concentrations (3 and 15 g/L) did accumulate preferentially at entrapped NAPL, i.e., it was capable of in situ targeting. The amount of MRNIP2 that targets a NAPL source depends on NAPL saturation (S(n)), presumably because the saturation controls the available NAPL/water interfacial area and the flow field through the NAPL source. At effective S(n) close or equal to 100%, MRNIP2 bypassed NAPL and accumulated only at the periphery of the entrapped NAPL region. At lower S(n), flow also carries MRNIP2 to NAPL/water interfaces internal to the entrapped NAPL region. However, the mass of accumulated MRNIP2 per unit available NAPL/water interfacial area is relatively constant (∼0.8 g/m(2) for MRNIP2 = 3 g/L) from S(n) = 13 to ∼100%, suggesting that NAPL targeting is mostly controlled by MRNIP2 sorption onto the NAPL/water interface.

Polymer-modified Fe0 nanoparticles target entrapped NAPL in two dimensional porous media: effect of particle concentration, NAPL saturation, and injection strategy.

Understanding of the entrapment and dissolution behavior of dense non-aqueous phase liquids (DNAPLs) in single fractures is important for modeling contaminant flux generation from fractured sites. Here a systematic numerical study is presented to investigate the effect of fracture aperture statistics on DNAPL migration, entrapment and dissolution within individual, variable-aperture fractures. Both fractures with open and closed bottom boundaries were considered. For the simulation a continuum-based two-phase model was used with a capillary pressure function which calculates the entry pressure based on the local aperture. Prior to application the model was compared against the invasion percolation approach and found more suitable for the present study, in particular as it allows a more versatile presentation of boundary conditions. The results showed that increasing aperture standard deviation and/or decreasing correlation length lead to larger amounts of entrapped DNAPL (due to the fact that larger standard deviation produces more distinct contrast between small and large aperture regions and the fact that longer correlation length provides more possible channels through the fracture) as well as larger maximum and average sizes of DNAPL blobs, and subsequently lead to longer times for complete dissolution. To understand the relationship between the solute flux and the remaining mass, a simplified source depletion function which links the outflow concentration to the DNAPL saturation was found adequate to describe the dissolution process for the case where the bottom boundary is open for DNAPL migration and thus the DNAPL does not accumulate to form a pool. The parameters in this function were not very sensitive to variations in correlation length but were sensitive to aperture standard deviation. The same average entrapped DNAPL saturation produced considerably smaller solute concentrations in cases with larger aperture variability due to the larger average size of DNAPL blobs (i.e., smaller contact area for DNAPL dissolution). Boundary conditions had a significant impact on DNAPL entrapment and dissolution. A closed boundary at the bottom led to DNAPL pooling (i.e., large continuous blobs) which causes significant tailing in the dissolution breakthrough curve due to water bypassing.

Effects of single-fracture aperture statistics on entrapment, dissolution and source depletion behavior of dense non-aqueous phase liquids.

Understanding the dissolution behavior of dense non-aqueous phase liquids (DNAPLs) in rock fractures under different entrapment conditions is important for remediation activities and any related predictive modeling. This study investigates DNAPL dissolution in variable aperture fractures under two important entrapment configurations, namely, entrapped residual blobs from gravity fingering and pooling in a dead-end fracture. We performed a physical dissolution experiment of residual DNAPL blobs in a vertical analog fracture using light transmission techniques. A high-resolution mechanistic (physically-based) numerical model has been developed which is shown to excellently reproduce the experimentally observed DNAPL dissolution. We subsequently applied the model to simulate dissolution of the residual blobs under different water flushing velocities. The simulated relationship between the Sherwood number Sh and Peclet number Pe could be well fitted with a simple power-law function (Sh=1.43Pe⁰·⁴³). To investigate mass transfer from dead-end pools, another type of trapping in rock fractures, entrapment and dissolution of DNAPL in a vertical dead-end fracture was simulated. As the entrapped pool dissolves, the depth of the interface between the DNAPL and the flowing water increases linearly with decreasing DNAPL saturation. The interfacial area remains more or less constant as DNAPL saturation decreases, unlike in the case of residual DNAPL blobs. The decreasing depth of the contact interface changes the flow field and causes decreasing water flow velocity above the top of the DNAPL pool, suggesting the dependence of the mass transfer rate on the depth of the interface, or alternatively, the remaining mass percentage in the fracture. Simulation results show that the resultant Sherwood number Sh is significantly smaller than in the case of residual blobs for any given Peclet number, indicating slower mass transfer. The results also show that the Sh can be well fitted with a power-law function of Pe and remaining mass percentage. The obtained relationships of dimensionless groups concerning the mass transfer characteristics at the level of individual fractures can be further used in predictive modeling of dissolution at a larger (fracture network) scale.

Article	Year
Particle size distribution, concentration, and magnetic attraction affect transport of polymer-modified Fe(0) nanoparticles in sand columns. Environmental science & technology\| PubMed ID: 19673310	2009
Empirical correlations to estimate agglomerate size and deposition during injection of a polyelectrolyte-modified Fe0 nanoparticle at high particle concentration in saturated sand. Journal of contaminant hydrology\| PubMed ID: 20926157	2010
Polymer-modified Fe0 nanoparticles target entrapped NAPL in two dimensional porous media: effect of particle concentration, NAPL saturation, and injection strategy. Environmental science & technology\| PubMed ID: 21678951	2011
Effects of single-fracture aperture statistics on entrapment, dissolution and source depletion behavior of dense non-aqueous phase liquids. Journal of contaminant hydrology\| PubMed ID: 22481125	2012
Dissolution of dense non-aqueous phase liquids in vertical fractures: effect of finger residuals and dead-end pools. Journal of contaminant hydrology\| PubMed ID: 23608741	2013

Fritjof Fagerlund

Biography

JoVE Journal Publications

Other Publications