printing-fabrication-bulk-heterojunction-solar-cells-situ-morphology

Printing Fabrication of Bulk Heterojunction Solar Cells and <em>In Situ</em> Morphology Characterization

Polymer-based materials hold promise as low-cost, flexible efficient photovoltaic devices. Most laboratory efforts to achieve high performance devices ...

University of Massachusetts, Amherst

This paper describes a facile method for coating Ag nanowires with uniform, ferromagnetic sheaths made of polycrystalline Ni. A typical sample of these core/sheath nanowires had a saturation magnetization around 33 emu g(-1). We also demonstrated the use of this magnetic property to align the nanowires by simply placing a suspension of the nanowires on a substrate in a magnetic field and allowing the solvent to evaporate. The electrical conductivity of these core/sheath nanowires (2 × 10(3) S cm(-1)) was two orders of magnitude lower than that of bulk Ag (6.3 × 10(5) S cm(-1)) and Ni (1.4 × 10(5) S cm(-1)). This is likely caused by the transfer of electrons from the Ag core to the Ni sheath due to the difference in work function between the two metals. The electrons are expected to experience an increased resistance due to spin-dependent scattering caused by the randomized magnetic domains in the polycrystalline, ferromagnetic Ni sheath. Studies on the structural changes to the Ni coating over time under different storage conditions show that storage of the nanowires on a substrate under ambient conditions leads to very little Ni oxidation after 6 months. These Ag/Ni core/sheath nanowires show promise in areas such as electronics, spintronics, and displays.

Facile synthesis of bimetallic Ag/Ni core/sheath nanowires and their magnetic and electrical properties.

This article focuses on the growth and transport properties of organic single-crystalline p-n junction nanoribbons. The development of organic nanoelectronics requires the fabrication of organic nanometer-sized p-n junctions for high-performance devices and integrated circuits. Here we demonstrate the formation of single-crystalline p-n junction nanoribbons of organic semiconductors by selective crystallization of copper hexadecafluorophthalocyanine (F(16)CuPc, n-type) on copper phthalocyanine (CuPc, p-type) single-crystalline nanoribbons. The crystallization of F(16)CuPc onto CuPc requires several parameters, including similar molecular structures, similar lattice constants, and pi-stacking along the nanoribbon axis. Ambipolar transport of the p-n junction nanoribbons was observed in field-effect transistors with balanced carrier mobilities of 0.05 and 0.07 cm(2) V(-1) s(-1) for F(16)CuPc and CuPc, respectively. A basic p-n junction nanoribbon photovoltaic device showed current rectification under AM 1.5 simulated light. The discrete p-n junction nanoribbons may serve as ideal systems for understanding basic charge-transport and photovoltaic behaviors at organic-organic interfaces.

Organic single-crystalline p-n junction nanoribbons.

Direct imaging of the bulk heterojunction (BHJ) thin film morphology in polymer-based solar cells is essential to understand device function and optimize efficiency. The morphology of the BHJ active layer consists of bicontinuous domains of the donor and acceptor materials, having characteristic length scales of several tens of nanometers, that reduces charge recombination, enhances charge separation, and enables electron and hole transport to their respective electrodes. Direct imaging of the morphology from the molecular to macroscopic level, though, is lacking. Though transmission electron tomography provides a 3D, real-space image of the morphology, quantifying the structure is not possible. Here we used high-resolution atomic force microscopy (AFM) in the tapping and nanomechanical modes to investigate the BHJ active layer morphology that, when combined with Ar(+) etching, provided unique insights with unparalleled spatial resolution. PCBM was seen to form a network that interpenetrated into the fibrillar network of the hole-conducting polymer, both being imbedded in a mixture of the two components. The free surface was found to be enriched with polymer crystals having a "face-on" orientation and the morphology at the anode interface was markedly different.

New insights into morphology of high performance BHJ photovoltaics revealed by high resolution AFM.

Organic solar cells based on a typical DPP polymer were systematically optimized by a solvent swelling assisted sequential deposition process. We investigated the influence of solvent swelling on the morphology and structure order of the swollen film and the resultant device performance. Morphological and structural characterization confirmed the realization of ideal bulk heterojunctions using a suitable swelling solvent. A trilayered morphology was also found with the conjugated polymer concentrated bottom layer, PC71BM concentrated top layer, and interpenetrated networks of donor and acceptor in the middle by solvent swelling instead of thermal annealing in the sequential solution processing method. We proposed a simple strategy to optimize the sequential deposition fabricated devices by tuning the concentration of the PC71BM solution instead of thermal annealing. The best device showed a PCE of 7.59% with a Voc of 0.61 V, Jsc of 17.95 mA/cm(2), and FF of 69.6%, which is the highest reported efficiency for devices fabricated by a sequential processing method and among the best results for DPP polymers.

Sequential deposition: optimization of solvent swelling for high-performance polymer solar cells.

The mini-slot-die coater offers a simple, convenient, materials-efficient route to print bulk-heterojunction (BHJ) organic photovoltaics (OPVs) that show efficiencies similar to spin-coating. Grazing-incidence X-ray diffraction (GIXD) and GI small-angle X-ray scattering (GISAXS) methods are used in real time to characterize the active-layer formation during printing. A polymer-aggregation-phase-separation-crystallization mechanism for the evolution of the morphology describes the observations.

Article	Year
Facile synthesis of bimetallic Ag/Ni core/sheath nanowires and their magnetic and electrical properties. Small (Weinheim an der Bergstrasse, Germany)\| PubMed ID: 20677185	2010
Organic single-crystalline p-n junction nanoribbons. Journal of the American Chemical Society\| PubMed ID: 20681577	2010
New insights into morphology of high performance BHJ photovoltaics revealed by high resolution AFM. Nano letters\| PubMed ID: 25184797	2014
Sequential deposition: optimization of solvent swelling for high-performance polymer solar cells. ACS applied materials & interfaces\| PubMed ID: 25482207	2015
Fast printing and in situ morphology observation of organic photovoltaics using slot-die coating. Advanced materials (Deerfield Beach, Fla.)\| PubMed ID: 25503869	2015

Sunzida Ferdous

Biography

JoVE Journal Publications

Other Publications