dispersion-nanomaterials-aqueous-media-towards-protocol

Dispersion of Nanomaterials in Aqueous Media: Towards Protocol Optimization

The sonication process is commonly used for de-agglomerating and dispersing nanomaterials in aqueous based media, necessary to improve homogeneity and ...

Fraunhofer Institute for Ceramic Technologies and Systems

Toxicological investigations on nanoparticles require a comprehensive physico-chemical characterization to get useful information about the powder as well as the behavior of the suspended nanoparticles in water and physiological media. Therefore, we characterized the often used TiO(2) P25 and developed procedures to get stable, homogeneous, and well-defined nanoparticle suspensions. A titration of the zeta potential as a function of the pH yielded the conclusion that the TiO(2) suspension is stable at a pH of 4 or lower. In this region the zeta potential is higher than 30 mV, which guarantees a high stability of the suspended particles. Hence, a stable TiO(2) initial suspension was prepared in 0.1 mM HCl having a mean particle size of 170 +/- 5 nm, which was determined by dynamic light scattering. Furthermore, the initial suspension was added to different physiological media (0.9% NaCl solution, phosphate-buffered saline [PBS], Hanks balanced salt solution [HBSS], Dulbecco's modified Eagle's medium [DMEM]) for studying the agglomeration behavior. As a result, the agglomeration kinetics at the same TiO(2) concentration is independent of the used media. Investigations with PBS containing bovine serum albumin (BSA) and DMEM supplemented with 10% FBS revealed that these protein additions inhibit the agglomeration of the particles. Thus, the physiological media contains particles that are stabilized through the steric or electrosteric effect of BSA and of the proteins in FBS, respectively. Consequently, the particles keep their size from the initial suspension. Finally, our procedure demonstrated on TiO(2) P25 results in homogeneously suspended particles in physiological media. This definite status of the particles means an improvement for toxicological testing and understanding.

Physico-chemical characterization in the light of toxicological effects.

One task in risk assessment of engineered nanoparticles is toxicological studies. A suitable interpretation of these investigations demands a comprehensive physical-chemical characterization. Here, we present an approach to gain well-dispersed nanoparticles in physiological media. Therefore, a step-by-step procedure is demonstrated on two different tungsten carbide nanopowders which can be transferred to other powders. The procedure includes a comprehensive powder characterization, followed by a preparation of a non-physiologic, electrostatically stable nanoparticle suspension and finally closes with investigations of the particles' behavior in different physiological media. Our study showed that the particles agglomerate in protein-free media. In this context, dependencies of mass- and surface-based nanoparticle concentrations as well as of different physiological media were analyzed. In the presence of bovine serum albumin (BSA) or serum, the agglomeration process is decelerated or, at the appropriate protein amount, prevented.

Physical-chemical characterization of tungsten carbide nanoparticles as a basis for toxicological investigations.

Injection of nanoscale zero-valent iron (nZVI) has recently gained great interest as emerging technology for in-situ remediation of chlorinated organic compounds from groundwater systems. Zero-valent iron (ZVI) is able to reduce organic compounds and to render it to less harmful substances. The use of nanoscale particles instead of granular or microscale particles can increase dechlorination rates by orders of magnitude due to its high surface area. However, classical nZVI appears to be hampered in its environmental application by its limited mobility. One approach is colloid supported transport of nZVI, where the nZVI gets transported by a mobile colloid. In this study transport properties of activated carbon colloid supported nZVI (c-nZVI; d50=2.4μm) are investigated in column tests using columns of 40cm length, which were filled with porous media. A suspension was pumped through the column under different physicochemical conditions (addition of a polyanionic stabilizer and changes in pH and ionic strength). Highest observed breakthrough was 62% of the injected concentration in glass beads with addition of stabilizer. Addition of mono- and bivalent salt, e.g. more than 0.5mM/L CaCl2, can decrease mobility and changes in pH to values below six can inhibit mobility at all. Measurements of colloid sizes and zeta potentials show changes in the mean particle size by a factor of ten and an increase of zeta potential from -62mV to -80mV during the transport experiment. However, results suggest potential applicability of c-nZVI under field conditions.

Transport of carbon colloid supported nanoscale zero-valent iron in saturated porous media.

The application of nanoscale zero-valent iron (nZVI) for subsurface remediation of groundwater contaminants is a promising new technology, which can be understood as alternative to the permeable reactive barrier technique using granular iron. Dechlorination of organic contaminants by zero-valent iron seems promising. Currently, one limitation to widespread deployment is the fast agglomeration and sedimentation of nZVI in colloidal suspensions, even more so when in soils and sediments, which limits the applicability for the treatment of sources and plumes of contamination. Colloid-supported nZVI shows promising characteristics to overcome these limitations. Mobility of Carbo-Iron Colloids (CIC) - a newly developed composite material based on finely ground activated carbon as a carrier for nZVI - was tested in a field application: In this study, a horizontal dipole flow field was established between two wells separated by 5.3m in a confined, natural aquifer. The injection/extraction rate was 500L/h. Approximately 1.2kg of CIC was suspended with the polyanionic stabilizer carboxymethyl cellulose. The suspension was introduced into the aquifer at the injection well. Breakthrough of CIC was observed visually and based on total particle and iron concentrations detected in samples from the extraction well. Filtration of water samples revealed a particle breakthrough of about 12% of the amount introduced. This demonstrates high mobility of CIC particles and we suggest that nZVI carried on CIC can be used for contaminant plume remediation by in-situ formation of reactive barriers.

A field investigation on transport of carbon-supported nanoscale zero-valent iron (nZVI) in groundwater.

Within the FP7 EU project NanoValid a consortium of six partners jointly investigated the hazard of silver nanoparticles (AgNPs) paying special attention to methodical aspects that are important for providing high-quality ecotoxicity data. Laboratories were supplied with the same original stock dispersion of AgNPs. All partners applied a harmonised procedure for storage and preparation of toxicity test suspensions. Altogether ten different toxicity assays with a range of environmentally relevant test species from different trophic levels were conducted in parallel to AgNP characterisation in the respective test media. The paper presents a comprehensive dataset of toxicity values and AgNP characteristics like hydrodynamic sizes of AgNP agglomerates and the share (%) of Ag(+)-species (the concentration of Ag(+)-species in relation to the total measured concentration of Ag). The studied AgNP preparation (20.4±6.8 nm primary size, mean total Ag concentration 41.14 mg/L, 46-68% of soluble Ag(+)-species in stock, 123.8±12.2 nm mean z-average value in dH2O) showed extreme toxicity to crustaceans Daphnia magna, algae Pseudokirchneriella subcapitata and zebrafish Danio rerio embryos (EC50<0.01 mg total Ag/L), was very toxic in the in vitro assay with rainbow trout Oncorhynchus mykiss gut cells (EC50: 0.01-1 mg total Ag/L); toxic to bacteria Vibrio fischeri, protozoa Tetrahymena thermophila (EC50: 1-10 mg total Ag/L) and harmful to marine crustaceans Artemia franciscana (EC50: 10-100 mg total Ag/L). Along with AgNPs, also the toxicity of AgNO3 was analyzed. The toxicity data revealed the same hazard ranking for AgNPs and AgNO3 (i.e. the EC50 values were in the same order of magnitude) proving the importance of soluble Ag(+)-species analysis for predicting the hazard of AgNPs. The study clearly points to the need for harmonised procedures for the characterisation of NMs. Harmonised procedures should consider: (i) measuring the AgNP properties like hydrodynamic size and metal ions species in each toxicity test medium at a range of concentrations, and (ii) including soluble metal salt control both in toxicity testing as well as in Ag(+)-species measurements. The present study is among the first nanomaterial interlaboratory comparison studies with the aim to improve the hazard identification testing protocols.

An interlaboratory comparison of nanosilver characterisation and hazard identification: Harmonising techniques for high quality data.

During the last decade, nanomaterials (NM) were extensively tested for potential harmful effects towards humans and environmental organisms. However, a sound hazard assessment was so far hampered by uncertainties and a low comparability of test results. The reason for the low comparability is a high variation in the (1) type of NM tested with regard to raw material, size and shape and (2) procedures before and during the toxicity testing. This calls for tailored, nanomaterial-specific protocols. Here, a structured approach is proposed, intended to lead to test protocols not only tailored to specific types of nanomaterials, but also to respective test system for toxicity testing. There are existing standards on single procedures involving nanomaterials, however, not all relevant procedures are covered by standards. Hence, our approach offers a detailed way of weighting several plausible alternatives for e.g. sample preparation, in order to decide on the procedure most meaningful for a specific nanomaterial and toxicity test. A framework of several decision trees (DT) and flow charts to support testing of NM is proposed as a basis for further refinement and in-depth elaboration. DT and flow charts were drafted for (1) general procedure-physicochemical characterisation, (2) choice of test media, (3) decision on test scenario and application of NM to liquid media, (4) application of NM to the gas phase, (5) application of NM to soil and sediments, (6) dose metrics, (S1) definition of a nanomaterial, and (S2) dissolution. The applicability of the proposed approach was surveyed by using experimental data retrieved from studies on nanoscale CuO. This survey demonstrated the DT and flow charts to be a convenient tool to systematically decide upon test procedures and processes, and hence pose an important step towards harmonisation of NM testing.

Towards sensible toxicity testing for nanomaterials: proposal for the specification of test design.

The presence of microplastic (MP) in the aquatic environment is recognized as a global-scale pollution issue. Secondary MP particles result from an ongoing fragmentation process governed by various biotic and abiotic factors. For a reliable risk assessment of these MP particles, knowledge about interactions with biota is needed. However, extensive testing with standard organisms under reproducible laboratory conditions with well-characterized MP suspensions is not available yet. As MP in the environment represents a mixture of particles differing in properties (e.g., size, color, polymer type, surface characteristics), it is likely that only specific particle fractions pose a threat towards organisms. In order to assign hazardous effects to specific particle properties, these characteristics need to be analyzed. As shown by the testing of particles (e.g. nanoparticles), characteristics other than chemical properties are important for the emergence of toxicity in organisms, and parameters such as surface area or size distribution need consideration. Therefore, the use of "well-defined" particles for ecotoxicological testing (i.e., standard particles) facilitates the establishment of causal links between physical-chemical properties of MP particles and toxic effects in organisms. However, the benefits of well-defined particles under laboratory conditions are offset by the disadvantage of the unknown comparability with MP in the environment. Therefore, weathering effects caused by biological, chemical, physical or mechanical processes have to be considered. To date, the characterization of the progression of MP weathering based on powder and suspension characterization methods is in its infancy. The aim of this commentary is to illustrate the prerequisites for testing MP in the laboratory from 3 perspectives: (i) knowledge of particle properties; (ii) behavior of MP in test setups involving ecotoxicological test organisms; and (iii) accordingly, test conditions that may need adjustment. Only under those prerequisites will reliable hazard assessment of MP be feasible. Integr Environ Assess Manag 2017;13:500-504. © 2017 SETAC.

Article	Year
Physico-chemical characterization in the light of toxicological effects. Inhalation toxicology\| PubMed ID: 19558232	2009
Physical-chemical characterization of tungsten carbide nanoparticles as a basis for toxicological investigations. Nanotoxicology\| PubMed ID: 20795896	2010
Transport of carbon colloid supported nanoscale zero-valent iron in saturated porous media. Journal of contaminant hydrology\| PubMed ID: 24914524	2014
A field investigation on transport of carbon-supported nanoscale zero-valent iron (nZVI) in groundwater. Journal of contaminant hydrology\| PubMed ID: 25864966	2015
An interlaboratory comparison of nanosilver characterisation and hazard identification: Harmonising techniques for high quality data. Environment international\| PubMed ID: 26638016	2016
Towards sensible toxicity testing for nanomaterials: proposal for the specification of test design. Science and technology of advanced materials\| PubMed ID: 27877848	2015
From the sea to the laboratory: Characterization of microplastic as prerequisite for the assessment of ecotoxicological impact. Integrated environmental assessment and management\| PubMed ID: 28440940	2017

Annegret Potthoff

Biography

JoVE Journal Publications

Other Publications