pore-scale-imaging-characterization-hydrocarbon-reservoir-rock

Pore-scale Imaging and Characterization of Hydrocarbon Reservoir Rock Wettability at Subsurface Conditions Using X-ray Microtomography

In situ wettability measurements in hydrocarbon reservoir rocks have only been possible recently. The purpose of this work is to present a protocol to ...

Imperial College London

We used X-ray micro-tomography to image the in situ wettability, the distribution of contact angles, at the pore scale in calcite cores from a producing hydrocarbon reservoir at subsurface conditions. The contact angle was measured at hundreds of thousands of points for three samples after twenty pore volumes of brine flooding.We found a wide range of contact angles with values both above and below 90°. The hypothesized cause of wettability alteration by an adsorbed organic layer on surfaces contacted by crude oil after primary drainage was observed with Scanning Electron Microscopy (SEM) and identified using Energy Dispersive X-ray (EDX) analysis. However, not all oil-filled pores were altered towards oil-wet conditions, which suggests that water in surface roughness, or in adjacent micro-porosity, can protect the surface from a strong wettability alteration. The lowest oil recovery was observed for the most oil-wet sample, where the oil remained connected in thin sheet-like layers in the narrower regions of the pore space. The highest recovery was seen for the sample with an average contact angle close to 90°, with an intermediate recovery in a more water-wet system, where the oil was trapped in ganglia in the larger regions of the pore space.

In situ characterization of mixed-wettability in a reservoir rock at subsurface conditions.

Pore-scale two-phase flow modeling is an important technology to study a rock's relative permeability behavior. To investigate if these models are predictive, the calculated pore-scale fluid distributions which determine the relative permeability need to be validated. In this work, we introduce a methodology to quantitatively compare models to experimental fluid distributions in flow experiments visualized with microcomputed tomography. First, we analyzed five repeated drainage-imbibition experiments on a single sample. In these experiments, the exact fluid distributions were not fully repeatable on a pore-by-pore basis, while the global properties of the fluid distribution were. Then two fractional flow experiments were used to validate a quasistatic pore network model. The model correctly predicted the fluid present in more than 75% of pores and throats in drainage and imbibition. To quantify what this means for the relevant global properties of the fluid distribution, we compare the main flow paths and the connectivity across the different pore sizes in the modeled and experimental fluid distributions. These essential topology characteristics matched well for drainage simulations, but not for imbibition. This suggests that the pore-filling rules in the network model we used need to be improved to make reliable predictions of imbibition. The presented analysis illustrates the potential of our methodology to systematically and robustly test two-phase flow models to aid in model development and calibration.

Validation of model predictions of pore-scale fluid distributions during two-phase flow.

A quantitative in situ characterization of the impact of surface roughness on wettability in porous media is currently lacking. We use reservoir condition micrometer-resolution X-ray tomography combined with automated methods for the measurement of contact angle, interfacial curvature, and surface roughness to examine fluid/fluid and fluid/solid interfaces inside a porous material. We study oil and water in the pore space of limestone from a giant producing oilfield, acquiring millions of measurements of curvature and contact angle on three millimeter-sized samples. We identify a distinct wetting state with a broad distribution of contact angle at the submillimeter scale with a mix of water-wet and water-repellent regions. Importantly, this state allows both fluid phases to flow simultaneously over a wide range of saturation. We establish that, in media that are largely water wet, the interfacial curvature does not depend on solid surface roughness, quantified as the local deviation from a plane. However, where there has been a significant wettability alteration, rougher surfaces are associated with lower contact angles and higher interfacial curvature. The variation of both contact angle and interfacial curvature increases with the local degree of roughness. We hypothesize that this mixed wettability may also be seen in biological systems to facilitate the simultaneous flow of water and gases; furthermore, wettability-altering agents could be used in both geological systems and material science to design a mixed-wetting state with optimal process performance.

Article	Year
In situ characterization of mixed-wettability in a reservoir rock at subsurface conditions. Scientific reports\| PubMed ID: 28883407	2017
Validation of model predictions of pore-scale fluid distributions during two-phase flow. Physical review. E\| PubMed ID: 29906889	2018
Wettability in complex porous materials, the mixed-wet state, and its relationship to surface roughness. Proceedings of the National Academy of Sciences of the United States of America\| PubMed ID: 30120127	2018

Ahmed AlRatrout

Biography

JoVE Journal Publications

Other Publications