3d-planning-printing-patient-specific-implants-for-reconstruction

3D Planning and Printing of Patient Specific Implants for Reconstruction of Bony Defects

We are in the midst of the 3D era in most aspects of life, and especially in medicine. The surgical discipline is one of the major players in the medical ...

three-dimensional-reconstruction-of-orbital-fractures

Three-Dimensional Reconstruction of Orbital Fractures

Reconstruction of orbital fractures can be challenging. The limited exposure, involvement of several wall defects, and the variable three-dimensional (3D) ...

Rambam Medical Care Center

The research aimed at investigating potential correlations between craniofacial morphological measurements and mandibular pericondylar fractures, based on a retrospective study of 380 mandible fractures treated in our department, during 2010 to 2017. Predictors included morphological measurements and features. Primary outcome was presence of pericondylar fracture; 133 pericondylar fractures were found, including subcondylar, condylar neck, and condylar head fractures. Condylar neck fractures showed negative correlations with condylar neck width (5.7 mm versus 6.7 mm sagittaly, and 6.1 mm versus 6.8 mm coronally, respectively). Gonial angle (117.3 degrees versus 128.7), and mandibular length 106.2 mm versus 110.4 mm, respectively) showed negative correlation with all pericondylar fractures. Ramus height correlated positively with pericondylar fractures (53.6 mm versus 51.2 mm, respectively). Thus, our results showed condylar neck width was a predictor for condylar neck fractures. In addition, individuals suffering from pericondylar fractures had significantly smaller gonial angles, longer ramus height, and shorter mandibular length. These morphologic features are characteristic of individuals with decreased anterior facial height. Our results corroborated a previous study we had conducted, which suggested that increased anterior vertical growth correlates with angle fractures.

Craniofacial Morphometric Features Associated With Pericondylar Fractures of the Mandible.

Limited bone quality in the posterior maxilla results in low success rates for dental implants. Various bone augmentation methods have been described, yet most require two-step surgical procedures with relatively high rates of resorption and failure. An alternative for these patients is zygomatic implants. Zygomatic implants utilize the basal craniofacial bone.

Extramaxillary Zygomatic Implants: An Alternative Approach for the Reconstruction of the Atrophic Maxilla.

Titanium plats are the gold-standard for fracture fixation. Titanium is considered biocompatible, corrosion resistant with an elasticity-modulus closest to bone. Nonetheless, titanium plates are not always as inherent as hoped. The authors investigated morbidity associated with titanium plates in mandibular fractures. A retrospective study of mandibular fractures treated between 2000 and 2018 using internal-fixation was conducted. Data included age, gender, complications, and location. Predictor-variable was location. Outcome-variable was plate removal. A total of 571 patients were included, 107 resulted in plate removal (18.7%). Body was the most prevalent location of fracture (29.3%). Symphysis/para-sym-physis showed the highest removal rate (24.1%), followed by body and angle (21.3/19.8%). A total of 23.4% of double-plating cases resulted in plate removal, upper-border in 15% and lower-border in 8.8%, all reconstruction-plates. Exposure was the most frequent complication leading to removal. Although titanium plates are the gold standard, almost every fifth patient returns for plate removal. Age-distribution emphasizing 41 to 50 with decrease towards extremities may imply better healing in the young and soft-tissue elasticity and less complaints in the elderly. Significantly more complications in double-plating compared to lower border suggests proximity to the oral-cavity as a risk-factor for removal. Complication rates and patterns are not negligible and perhaps should encourage clinicians to consider using biodegradable-systems for upper-border plates.

Is Open Reduction Internal Fixation Using Titanium Plates in the Mandible as Successful as We Think?

Comminuted fractures of the jaws are complex injuries requiring special attention. In the past, treatment included closed reduction using maxillomandibular fixation. With advancements in technology and fixation systems, open reduction became a prevalent option. These fractures are difficult to reconstruct during the primary treatment phase, thus resulting in higher complication rates. The introduction of three-dimensional (3D) planning and printing brought about superior outcomes, yet these focus on secondary reconstruction due to the need for outsourcing planning and titanium printing.

ArticleTotal : 2	Year
Publication title Cited by 5	2020
Publication title	2025

Article	Year
Craniofacial Morphometric Features Associated With Pericondylar Fractures of the Mandible. The Journal of craniofacial surgery\| PubMed ID: 31490441	2019
Extramaxillary Zygomatic Implants: An Alternative Approach for the Reconstruction of the Atrophic Maxilla. Annals of maxillofacial surgery\| PubMed ID: 32855928	2020
Is Open Reduction Internal Fixation Using Titanium Plates in the Mandible as Successful as We Think? The Journal of craniofacial surgery\| PubMed ID: 34608010	2022
Real-time Reconstruction of Comminuted Mandibular Fractures Using 3D Printing. Plastic and reconstructive surgery. Global open\| PubMed ID: 38510331	2024

Ori Blanc

Biography

JoVE Journal Publications

Other Publications