an-vitro-hemodynamic-loop-model-to-investigate-hemocytocompatibility

An In Vitro Hemodynamic Loop Model to Investigate the Hemocytocompatibility and Host Cell Activation of Vascular Medical Devices

In this study, the hemocompatibility of tubes with an inner diameter of 5 mm made of polyvinyl chloride (PVC) and coated with different bioactive ...

Otto-von-Guericke-University

The combination of high strength and toughness, excellent wear resistance and moderate density makes zirconia-toughened alumina (ZTA) a favorable ceramic, and the foam version of it may also exhibit excellent properties. Here, ZTA foams were prepared by the polymer sponge replication method. We developed an immersion infiltration approach with simple equipment and operations to fill the hollow struts in as-prepared ZTA foams, and also adopted a multiple recoating method (up to four cycles) to strengthen them. The solid load of the slurry imposed a significant influence on the properties of the ZTA foams. Immersion infiltration gave ZTA foams an improvement of 1.5 MPa in compressive strength to 2.6 MPa at 87% porosity, only resulting in a moderate reduction of porosity (2-3%). The Weibull modulus of the infiltrated foams was in the range of 6-9. The recoating method generated an increase in compression strength to 3.3-11.4 MPa with the reduced porosity of 58-83%. The recoating cycle dependency of porosity and compression strength is nearly linear. The immersion infiltration strategy is comparable to the industrially-established recoating method and can be applied to other reticulated porous ceramics (RPCs).

Improving the Strength of ZTA Foams with Different Strategies: Immersion Infiltration and Recoating.

The present work describes the combination of the well-established dispersion infiltration of the hollow struts in reticulated porous ceramics (RPCs) and the salt solution infiltration of the remaining strut porosity. This approach is applied on alumina foams, which are loaded subsequently with a dispersion of sub-micrometer alumina particles and a ZrO(NO) solution. The zirconyl nitrate is converted into a ZrO transformation toughening phase during the final sintering step. As a consequence of the complex microstructure evolution during the consecutive infiltration cycles, the reinforcement phase concentrates selectively at the weak spots of RPC structures-namely, the hollow strut cavities and longitudinal cracks along the struts. As a consequence, a severe improvement of the compressive strength is observed: The average compressive strength, normalized to a porosity of 91.6 vol.%, is 1.47 MPa for the AlO/ZrO infiltrated foams, which is an improvement by 40% with respect to alumina-only loaded foams (1.05 MPa) or by 206% compared to uninfiltrated alumina RPCs (0.48 MPa). The compressive strength results are correlated to infiltration parameters and the properties of the infiltration fluids, for example the rheological behavior and the size of the Zr solute species in the respective ZrO(NO) solution.

Refitting of Zirconia Toughening into Open-Cellular Alumina Foams by Infiltration with Zirconyl Nitrate.

Open-cell aluminum foams were manufactured by a sponge replication technique having a total porosity of ~90%. The influence of the thermal processing conditions such as atmosphere and temperature on the cellular structure, phase composition porosity, thermal conductivity, and compressive strength of the foams was studied. It was found that the thermal processing of aluminum foams in Ar at temperatures up to 800 °C led to aluminum foams with a reduced strut porosity, a lower amount of aluminum oxide, a higher thermal conductivity, and a higher compression strength, compared to foams thermally processed in air. These results were explained by the lower amount of aluminum oxide after thermal processing of the foams.

Open-Cell Aluminum Foams by the Sponge Replication Technique.

PZT-silsesquioxane-based 0-3 hybrid materials are prepared by mixing lead zirconate titanate (Pb(Zr,Ti)O; PZT) powder with a [R-SiO] (R = H, CH, CH=CH, CH) silsequioxane preceramic polymer. A PZT load up to 55 vol.% can be reached in the final composite. The piezoelectric and mechanical properties are investigated as a function of the filler content and are compared with theoretical models and reference samples made of the pure preceramic polymer or PZT filler. The piezoelectric response of the composites, as expressed by the relative permittivity and the piezoelectric coefficients d and g, increases with an increasing PZT content. The bending strength of the composites ranges between 15 MPa and 31 MPa without a clear correlation to the filler content. The thermal conductivity increases significantly from 0.14 W∙m∙K for the pure polymer-derived ceramic (PDC) matrix to 0.30 W∙m∙K for a sample containing 55 vol.% PZT filler. From X-ray diffraction experiments (XRD), specific interactions between the filler and matrix are observed; the crystallization of the PDC matrix in the presence of the PZT filler is inhibited; conversely, the PDC matrix results in a pronounced decomposition of the filler compared to the pure PZT material.

Phase Evolution, Filler-Matrix Interactions, and Piezoelectric Properties in Lead Zirconate Titanate (PZT)-Filled Polymer-Derived Ceramics (PDCs).

The present study reports on the microstructural evolution and room temperature plasticity of V(‑Si)‑B alloys with respect to the V solid solution (V)‑VB phase region. To investigate the occurring effects systematically, different binary V‑B and ternary V‑Si‑B alloys were produced by conventional arc melting. Scanning electron microscope (SEM) analyses and X-ray diffraction (XRD) measurements were used to characterize the resulting as-cast microstructures. For the first time, the eutectic composition was systematically traced from the binary V‑B domain to the ternary V‑Si‑B system. The observations discover that the binary eutectic trough (V‑VB) seems to reach into the ternary system up to an alloy composition of V‑5Si‑9B. Room temperature compression tests were carried out in order to study the impact of single-phase and multi-phase microstructures on the strength and plasticity of binary and ternary alloys. The results indicate that the V phase controls the plastic deformability in the V‑VB eutectic microstructure whereas the intermetallic VB acts as a strong hardening phase.

Microstructure and Compression Properties of V‑VB Eutectic Alloys in the V-Si-B System.

Open-celled ceramic composite foams were prepared from NiO and yttria-stabilized zirconia (YSZ) powders by the polymer sponge replication (Schwartzwalder) technique using the respective aqueous dispersions. Mechanically stable NiO-YSZ foams with an average porosity of 93 vol.% were obtained. After chemical reduction of the NiO phase with hydrogen, cellular Ni-YSZ cermet structures were obtained. They are characterized by an electric conductivity up to 19∙10 S∙m which can be adjusted by both, the Ni volume fraction, and the sintering/reduction procedure. The NiO-YSZ ceramic foams, as well as the cellular Ni-YSZ cermets prepared therefrom, were characterized with respect to their microstructure by scanning electron microscopy, confocal Raman microscopy and X-ray diffraction with Rietveld analysis. In addition, the compressive strength, the electric conductivity and the thermal conductivity were determined. The collected data were then correlated to the sample microstructure and porosity and were also applied for modelling of the mechanical and electric properties of the bulk Ni-YSZ strut material.

Article	Year
Improving the Strength of ZTA Foams with Different Strategies: Immersion Infiltration and Recoating. Materials (Basel, Switzerland)\| PubMed ID: 28773093	2017
Refitting of Zirconia Toughening into Open-Cellular Alumina Foams by Infiltration with Zirconyl Nitrate. Materials (Basel, Switzerland)\| PubMed ID: 31212735	2019
Open-Cell Aluminum Foams by the Sponge Replication Technique. Materials (Basel, Switzerland)\| PubMed ID: 31766482	2019
Phase Evolution, Filler-Matrix Interactions, and Piezoelectric Properties in Lead Zirconate Titanate (PZT)-Filled Polymer-Derived Ceramics (PDCs). Materials (Basel, Switzerland)\| PubMed ID: 32224976	2020
Microstructure and Compression Properties of V‑VB Eutectic Alloys in the V-Si-B System. Materials (Basel, Switzerland)\| PubMed ID: 32370030	2020
Cellular Nickel-Yttria/Zirconia (Ni-YSZ) Cermet Foams: Manufacturing, Microstructure and Properties. Materials (Basel, Switzerland)\| PubMed ID: 32466407	2020

Ulf Betke

Biography

JoVE Journal Publications

Other Publications