harvesting-disaggregation-an-overlooked-step-biofilm-methods

Harvesting and Disaggregation: An Overlooked Step in Biofilm Methods Research

Biofilm methods consist of four distinct steps: growing the biofilm in a relevant model, treating the mature biofilm, harvesting the biofilm from the ...

Montana State University

This protocol describes how to grow a Pseudomonas aeruginosa biofilm under low fluid shear close to the air-liquid interface using the drip flow reactor (DFR). The DFR can model environments such as food-processing conveyor belts, catheters, lungs with cystic fibrosis and the oral cavity. The biofilm is established by operating the reactor in batch mode for 6 h. A mature biofilm forms as the reactor operates for an additional 48 h with a continuous flow of nutrients. During continuous flow, the biofilm experiences a low shear as the media drips onto a surface set at a 10 degrees angle. At the end of 54 h, biofilm accumulation is quantified by removing coupons from the reactor channels, rinsing the coupons to remove planktonic cells, scraping the biofilm from the coupon surface, disaggregating the clumps, then diluting and plating for viable cell enumeration. The entire procedure takes 13 h of active time that is distributed over 5 d.

A method for growing a biofilm under low shear at the air-liquid interface using the drip flow biofilm reactor.

The inactivation of  biofilms grown on glass under high shear stress and exposed to a range of dissolved ozone concentrations (2, 5 and 7 ppm) at 10 and 20 min was investigated. The regression equation, log reduction (biofilm) = 0.64 + 0.59×(C - 2) + 0.33×(T - 10), described the dependence of biofilm inactivation on the dissolved ozone concentration (C, ppm) and contact time (T, min). The predicted D-values were 11.1, 5.7 and 2.2 min at 2, 5 and 7 ppm, respectively. Inactivation of biofilms grown on various surfaces was tested at a single dissolved ozone concentration of 5 ppm and a single exposure time of 20 min. Biofilms grown on plastic materials showed inactivation results similar to that of biofilms on glass, while biofilms grown on ceramics were statistically significantly more difficult to inactivate, suggesting the importance of utilizing non-porous materials in industrial and clinical settings.

Inactivation of  biofilms formed under high shear stress on various hydrophilic and hydrophobic surfaces by a continuous flow of ozonated water.

Methods validated by a standard setting organization enable public, industry and regulatory stakeholders to make decisions on the acceptability of products, devices and processes. This is because standard methods are demonstrably reproducible when performed in different laboratories by different researchers, responsive to different products, and rugged when small (usually inadvertent) variations from the standard procedure occur. The Single Tube Method (ASTM E2871) is a standard method that measures the efficacy of antimicrobials against biofilm bacteria that has been shown to be reproducible, responsive and rugged. In support of the reproducibility assessment, a six-laboratory study was performed using three antimicrobials: a sodium hypochlorite, a phenolic and a quaternary/alcohol blend, each tested at low and high efficacy levels. The mean log reduction in viable bacteria in this study ranged from 2.32 to 4.58 and the associated reproducibility standard deviations ranged from 0.89 to 1.67. Independent follow-up testing showed that the method was rugged with respect to deviations in sonication duration and sonication power but slightly sensitive to sonicator reservoir degassing and tube location within the sonicator bath. It was also demonstrated that when a coupon was dropped into a test tube, bacteria can splash out of reach of the applied antimicrobials, resulting in substantial bias when estimating log reductions for the products tested. Bias can also result when testing products that hinder the harvesting of microbes from test surfaces. The culmination of this work provided recommended changes to the early version of the standard method E2871-13 (ASTM, 2013b) including use of splashguards and microscopy checks. These changes have been incorporated into a revised ASTM method E2871-19 (ASTM 2019) that is the basis for the first regulatory method (ATMP-MB-20) to substantiate "kills biofilm" claims for antimicrobials registered and sold in the US.

Development, standardization, and validation of a biofilm efficacy test: The single tube method.

A standard method for growing Pseudomonas aeruginosa biofilm in the Drip Flow Biofilm Reactor was assessed in a 10-laboratory study. The mean log density was 9.29 Log(CFU/cm). The repeatability and reproducibility SDs were equal to 0.22 and 0.24, respectively, providing statistical confidence in data generated by the method.

Drip flow reactor method exhibits excellent reproducibility based on a 10-laboratory collaborative study.

Listeria monocytogenes is one of the most concerning pathogens for the food industry due to its ability to form biofilms, particularly in difficult-to-clean sites of processing facilities. There is a current industry-wide lack of data to refer to when selecting a strategy to control L. monocytogenes biofilms in the food premises. Many strategies have been developed to study biofilm formation of bacteria; however, few have targeted L. monocytogenes biofilms under dynamic conditions. This study addresses the biofilm formation ability of L. monocytogenes on stainless steel and polycarbonate under dynamic conditions using TSBYE or BHI as media culture at 30 °C or 37 °C. Higher cell counts were recovered at 30 °C in TSBYE on polycarbonate while lower counts were obtained at 37 °C in BHI on stainless steel (P < 0.05). Nonetheless, all factors (temperature, media and material) were statistically significant (P < 0.05) and an interaction between temperature and media was observed (P < 0.05). To our knowledge, this work represents an initial framework to develop L. monocytogenes biofilms under different dynamic conditions. The use of CDC Biofilm Reactor is not widely used yet in the food industry and represent a novel approach to help sanitary control strategies implementation.

Article	Year
A method for growing a biofilm under low shear at the air-liquid interface using the drip flow biofilm reactor. Nature protocols\| PubMed ID: 19528953
Inactivation of biofilms formed under high shear stress on various hydrophilic and hydrophobic surfaces by a continuous flow of ozonated water. Biofouling\| PubMed ID: 30311502	2018
Development, standardization, and validation of a biofilm efficacy test: The single tube method. Journal of microbiological methods\| PubMed ID: 31491442
Drip flow reactor method exhibits excellent reproducibility based on a 10-laboratory collaborative study. Journal of microbiological methods\| PubMed ID: 32454049	2020
The use of a CDC biofilm reactor to grow multi-strain Listeria monocytogenes biofilm. Food microbiology\| PubMed ID: 32950174	2020

Diane K. Walker

Biography

JoVE Journal Publications

Other Publications