fabrication-densification-replica-molding-3d-carbon-nanotube

Fabrication, Densification, and Replica Molding of 3D Carbon Nanotube Microstructures

The introduction of new materials and processes to microfabrication has, in large part, enabled many important advances in microsystems, lab-on-a-chip ...

University of Michigan 

We report that nanoparticulate zirconia (ZrO(2)) catalyzes both growth of single-wall and multiwall carbon nanotubes (CNTs) by thermal chemical vapor deposition (CVD) and graphitization of solid amorphous carbon. We observe that silica-, silicon nitride-, and alumina-supported zirconia on silicon nucleates single- and multiwall carbon nanotubes upon exposure to hydrocarbons at moderate temperatures (750 degrees C). High-pressure, time-resolved X-ray photoelectron spectroscopy (XPS) of these substrates during carbon nanotube nucleation and growth shows that the zirconia catalyst neither reduces to a metal nor forms a carbide. Point-localized energy-dispersive X-ray spectroscopy (EDAX) using scanning transmission electron microscopy (STEM) confirms catalyst nanoparticles attached to CNTs are zirconia. We also observe that carbon aerogels prepared through pyrolysis of a Zr(IV)-containing resorcinol-formaldehyde polymer aerogel precursor at 800 degrees C contain fullerenic cage structures absent in undoped carbon aerogels. Zirconia nanoparticles embedded in these carbon aerogels are further observed to act as nucleation sites for multiwall carbon nanotube growth upon exposure to hydrocarbons at CVD growth temperatures. Our study unambiguously demonstrates that a nonmetallic catalyst can catalyze CNT growth by thermal CVD while remaining in an oxidized state and provides new insight into the interactions between nanoparticulate metal oxides and carbon at elevated temperatures.

Nanoscale zirconia as a nonmetallic catalyst for graphitization of carbon and growth of single- and multiwall carbon nanotubes.

The carbon nanotube (CNT) industry is expanding rapidly, yet little is known about the potential environmental impacts of CNT manufacture. Here, we evaluate the effluent composition of a representative multiwalled CNT synthesis by catalytic chemical vapor deposition (CVD) in order to provide data needed to design strategies for mitigating any unacceptable emissions. During thermal pretreatment of the reactant gases (ethene and H(2)), we found over 45 side-products were formed, including methane, volatile organic compounds (VOCs), and polycyclic aromatic hydrocarbons (PAHs). This finding suggests several environmental concerns with the existing process, including potential discharges of the potent greenhouse gas, methane (up to 1.7%), and toxic compounds such as benzene and 1,3-butadiene (up to 36000 ppmv). Extrapolating these laboratory-scale data to future industrial CNT production, we estimate that (1) contributions of atmospheric methane will be negligible compared to other existing sources and (2) VOC and PAH emissions may become important on local scales but will be small when compared to national industrial sources. As a first step toward reducing such unwanted emissions, we used continuous in situ measures of CNT length during growth and sought to identify which thermally generated compounds correlated with CNT growth rate. The results suggested that, in future CNT production approaches, key reaction intermediates could be delivered to the catalyst without thermal treatment. This would eliminate the most energetically expensive component of CVD synthesis (heating reactant gases), while reducing the formation of unintended byproducts.

Early evaluation of potential environmental impacts of carbon nanotube synthesis by chemical vapor deposition.

Thermal treatments of feedstock gases (e.g., C(2)H(4)/H(2)) used during carbon nanotube (CNT) synthesis result in the formation of a complex mixture of volatile organic compounds and polycyclic aromatic hydrocarbons. Some of these are likely important CNT precursors, while others are superfluous and possibly degrade product quality, form amorphous carbon, and/or contribute to growth termination. To simulate the effect of thermal treatment without this chemical complexity, we delivered trace amounts of individual hydrocarbons, along with ethylene and hydrogen, to a cold-wall atmospheric pressure reactor containing a locally heated metal catalyst (Fe on Al(2)O(3)). Using these compound-specific experiments, we demonstrate that many alkynes (e.g., acetylene, methyl acetylene, and vinyl acetylene) accelerate multiwalled CNT formation with this catalyst system. Furthermore, ethylene is required for enhanced CNT growth, suggesting that the alkyne and ethylene may react in concert at the metal catalyst. This presents a distinct CNT formation mechanism where the chemical precursors may be intact during C-C bond formation, such as in polymerization reactions, challenging the widely accepted hypothesis that precursors completely dissociate into C (or C(2)) units before "precipitating" from the metal. Armed with these mechanistic insights, we were able to form high-purity CNTs rapidly with a 15-fold improvement in yield, a 50% reduction in energetic costs, and order of magnitude reduction in unwanted byproduct formation (e.g., toxic and smog-forming chemicals and greenhouse gases).

Multiple alkynes react with ethylene to enhance carbon nanotube synthesis, suggesting a polymerization-like formation mechanism.

We demonstrate carbon nanotube (CNT) composite-based optoacoustic transmitters that generate strong and high frequency ultrasound. The composite consists of CNTs grown on a substrate, which are embedded in elastomeric polymer used as an acoustic transfer medium. Under pulsed laser excitation, the composite generates very strong optoacoustic pressure: 18 times stronger than a Cr film reference and five times stronger than a gold nanoparticle composite with the same polymer. This enhancement persists over a broadband frequency range of up to 120 MHz and is confirmed by calculation. We suggest the CNT-polymer composites as highly efficient optoacoustic transmitters for high resolution ultrasound imaging.

Article	Year
Nano letters\| PubMed ID: 18484777	2008
Nano letters\| PubMed ID: 18837566	2008
The Review of scientific instruments\| PubMed ID: 19256658	2009
Nanoscale zirconia as a nonmetallic catalyst for graphitization of carbon and growth of single- and multiwall carbon nanotubes. Journal of the American Chemical Society\| PubMed ID: 19663436	2009
ACS nano\| PubMed ID: 19691287	2009
Angewandte Chemie (International ed. in English)\| PubMed ID: 19697387	2009
Nano letters\| PubMed ID: 19719143	2009
Early evaluation of potential environmental impacts of carbon nanotube synthesis by chemical vapor deposition. Environmental science & technology\| PubMed ID: 19924971	2009
Physical chemistry chemical physics : PCCP\| PubMed ID: 20407718	2010
Nanoscale\| PubMed ID: 20644774	2010
Advanced materials (Deerfield Beach, Fla.)\| PubMed ID: 20814919	2010
Multiple alkynes react with ethylene to enhance carbon nanotube synthesis, suggesting a polymerization-like formation mechanism. ACS nano\| PubMed ID: 21050015	2010
Carbon nanotube composite optoacoustic transmitters for strong and high frequency ultrasound generation. Applied physics letters\| PubMed ID: 21200445	2010
Physical review. E, Statistical, nonlinear, and soft matter physics\| PubMed ID: 21230285	2010
Lab on a chip\| PubMed ID: 21451817	2011
Langmuir : the ACS journal of surfaces and colloids\| PubMed ID: 21504164	2011
ACS nano\| PubMed ID: 21591620	2011
Journal of applied physics\| PubMed ID: 21709723	2011
ACS nano\| PubMed ID: 21739995	2011
ACS nano\| PubMed ID: 21800907	2011
Nanotechnology\| PubMed ID: 21918300	2011
ACS nano\| PubMed ID: 22023221	2011
Angewandte Chemie (International ed. in English)\| PubMed ID: 22162366	2012
The Review of scientific instruments\| PubMed ID: 22299983	2012
Advanced materials (Deerfield Beach, Fla.)\| PubMed ID: 22396318	2012
ACS nano\| PubMed ID: 22571676	2012
Nanoscale\| PubMed ID: 22644444	2012

A. John Hart

Biography

JoVE Journal Publications

Other Publications