demonstrating-simplicity-situ-temperature-monitoring-mechanochemical

Demonstrating the Simplicity and In Situ Temperature Monitoring of the Mechanochemical Synthesis of Metal Chalcogenides Suitable for Thermoelectrics

Mechanochemical synthesis is an extremely useful strategy to reach thermoelectric materials due to its solvent-free one-step character, as the targeted ...

Technical University of Košice

The article describes the implementation of IoT technology in the teaching of microprocessor technology. The method presented in the article combines the reality and virtualization of the microprocessor technology laboratory. A created IoT monitoring device monitors the students' microcontroller pins and sends the data to the server to which the teacher is connected via the control application. The teacher has the opportunity to monitor the development of tasks and student code of the program, where the functionality of these tasks can be verified. Thanks to the IoT remote laboratory implementation, students' tasks during the lesson were improved. As many as 53% ( = 8) of those students who could improve their results achieved an improvement of one or up to two tasks during class. Before the IoT remote laboratory application, up to 30% ( = 6) of students could not solve any task and only 25% ( = 5) solved two tasks (full number of tasks) during the class. Before implementation, 45% ( = 9) solved one problem. After applying the IoT remote laboratory, these numbers increased significantly and up to 50% ( = 10) of students solved the full number of tasks. In contrast, only 10% ( = 2) of students did not solve any task.

Remote IoT Education Laboratory for Microcontrollers Based on the STM32 Chips.

The paper deals with a brief overview of magnetoelastic sensors and magnetoelastic sensors used in general for sensing bending forces, either directly or sensing bent structures, and defines the current state of the art. Bulk magnetoelastic force sensors are usually manufactured from transformer sheets or amorphous alloys. In praxis, usually, a compressive force is sensed by bulk magnetoelastic sensors; however, in this paper, the sensor is used for the measurement of bending forces, one reason being that the effect of such forces is easily experimentally tested, whereas compressive forces acting on a single sheet make buckling prevention a challenge. The measurement of the material characteristics that served as inputs into a FEM simulation model of the sensor is presented and described. The used material was considered to be mechanically and magnetically isotropic and magnetically nonlinear, even though the real sheet showed anisotropic behavior to some degree. A sinusoidal magnetizing current waveform was used in the experimental part of this paper, which was created by a current source. The effects of various frequencies, amplitudes, and sensor geometries were tested. The experimental part of this paper studies the sensors' RMS voltage changes to different loadings that bend the sheet out of its plane. The output voltage was the induced voltage in the secondary coil and was further analyzed to compute the linearity and sensitivity of the sensor at the specific current characteristic. It was found that for the given material, the most favorable operating conditions are obtained with higher frequency signals and higher excitation current amplitudes. The linearity of the sensor can be improved by placing the holes of the windings at different angles than 90° and by placing them further apart along the sheet's length. The current source was created by a simple op-amp voltage-to-current source controlled by a signal generator, which created a stable waveform. It was found that transformer sheet bending sensors with the dimensions described in this paper are suitable for the measurement of small forces in the range of up to 2 N for the shorter sensors and approximately 0.2 N for the longer sensors.

Driving Signal and Geometry Analysis of a Magnetoelastic Bending Mode Pressductor Type Sensor.

The advantageous applications of magnetic bistable microwires have emerged during long-lasting research. They have a wide range of applications in the scientific sphere or technical practice. They can be used for various applications, including magnetic memories, biomedicine, and sensors. This manuscript is focused on the last-mentioned application of microwires-sensors-discussing various digital signal processing techniques used in practical applications. Thanks to the highly sensitive properties of microwires and their two stable states of magnetization, it is possible to perform precise measurements with less demanding digital processing. The manuscript presents four practical signal-processing methods of microwire response using three different experiments. These experiments are focused on detecting the signal in a simple environment without an external magnetic background, measuring with the external background of a ferromagnetic core, and measuring in harsh conditions with a strong magnetic background. The experiments aim to propose the best method under various conditions, emphasizing the quality and signal processing speed of the microwire signal.

Article	Year
Remote IoT Education Laboratory for Microcontrollers Based on the STM32 Chips. Sensors (Basel, Switzerland)\| PubMed ID: 35214343	2022
Driving Signal and Geometry Analysis of a Magnetoelastic Bending Mode Pressductor Type Sensor. Sensors (Basel, Switzerland)\| PubMed ID: 37896487	2023
Advantages of Bistable Microwires in Digital Signal Processing. Sensors (Basel, Switzerland)\| PubMed ID: 38676040	2024

Patrik Jacko

Biography

JoVE Journal Publications

Other Publications