Name: friction on a banked road
Uploaded: 2026-06-24T13:03:27.731Z
Duration: 1 min 17 s
Channel: JoVE

Stellen Sie sich einen Bus mit einer Masse von drei Megagramm vor, dessen Schwerpunkt bei G liegt und sich mit konstanter Geschwindigkeit auf einer Steilstra&#xDF;e bewegt. Der Haftreibungskoeffizient zwischen den Reifen und der Stra&#xDF;e betr&#xE4;gt 0,5.Was ist der maximale Winkel der Steilkurve, in dem der Bus nicht ausrutscht oder kippt?Beim Zeichnen des Freik&#xF6;rperdiagramms werden Gravitations-, Reibungs- und Normalkr&#xE4;fte bezeichnet.Die Reibungskr&#xE4;fte an zwei Kontakten werden ausgedr&#xFC;ckt und das Gewicht des Busses in seine Bestandteile aufgel&#xF6;st.Ber&#xFC;cksichtigen Sie die Bedingung f&#xFC;r kein Ausrutschen. Da der Bus mit konstanter Geschwindigkeit f&#xE4;hrt, erf&#xFC;llt er die Gleichgewichtsbedingungen, und die resultierenden Kr&#xE4;fte, die in beide Richtungen auf ihn einwirken, sind Null.Das L&#xF6;sen der beiden Gleichungen ergibt den maximalen Winkel f&#xFC;r kein Verrutschen.Wenn der Bus zu kippen beginnt, verliert er den Kontakt zum oberen Punkt, und am oberen Punkt wirkt keine Reaktions- oder Reibungskraft.Um ein Kippen zu verhindern, muss das resultierende Moment um den unteren Punkt Null sein. Das L&#xF6;sen der Gleichung ergibt den maximalen Winkel f&#xFC;r kein Kippen.

<ol>
	<li>Hibbeler, R.C. (2016). Technische Mechanik: Statik. Vierzehnte Auflage, New Jersey: Pearson. S. 420.</li>
</ol>

reibung: problemlösung

Reibung ist eine wesentliche Kraft, die die Bewegung von Gegenst&#xE4;nden im t&#xE4;glichen Leben beeinflusst. Je nach Situation kann sie entweder n&#xFC;tzlich oder problematisch sein. Betrachten Sie einen Bus mit einer Masse von drei Megagramm und seinem Massenschwerpunkt an einem bestimmten Punkt, der mit konstanter Geschwindigkeit entlang einer geneigten Stra&#xDF;e f&#xE4;hrt. Der Reibungskoeffizient zwischen den Reifen und der Stra&#xDF;e betr&#xE4;gt 0,5. Finden Sie den maximalen Winkel der geneigten Stra&#xDF;e, bei dem der Bus nicht rutscht oder kippt.Zun&#xE4;chst muss eine visuelle Darstellung der gravitativen, reibenden und normalen Kr&#xE4;fte erstellt werden, die auf den Bus wirken. Diese Kr&#xE4;fte sind entscheidend, um das Gleichgewicht des Busses auf der geneigten Stra&#xDF;e zu verstehen.Als n&#xE4;chstes m&#xFC;ssen die Reibungskr&#xE4;fte an den beiden Kontaktstellen zwischen den Reifen und der Stra&#xDF;e analysiert werden. Dies kann erreicht werden, indem das Gewicht des Busses und seine Wechselwirkung mit dem Winkel der geneigten Stra&#xDF;e ber&#xFC;cksichtigt werden.<img style="height:350px;" src="/files/ftp_upload/14316/14316_PT_Figure_1v2.svg" alt="Figure 1" />Da der Bus mit konstanter Geschwindigkeit f&#xE4;hrt, erf&#xFC;llt er die Gleichgewichtsbedingungen. Das bedeutet, dass die auf den Bus in vertikaler und horizontaler Richtung wirkenden Kr&#xE4;fte ausgeglichen sind und der Bus auf der Stra&#xDF;e stabil bleibt.Durch die Untersuchung dieser Kr&#xE4;fte und ihrer Beziehungen kann man den maximalen Winkel finden, der sicherstellt, dass der Bus stabil bleibt, ohne die Neigung hinunterzurutschen.<img style="height:13px;" src="/files/ftp_upload/14316/14316_PT_Equation_1v2.svg" alt="Equation 1" /><img style="height:13px;" src="/files/ftp_upload/14316/14316_PT_Equation_2v2.svg" alt="Equation 2" />Nun sollte der Kipp-Punkt untersucht werden. Wenn der Bus anf&#xE4;ngt zu kippen, verliert er den Kontakt mit dem oberen Punkt (Kontaktstelle zwischen dem oberen Reifen und der Stra&#xDF;e) und es wirkt keine Reaktions- oder Reibungskraft am oberen Punkt.<img style="height:13px;" src="/files/ftp_upload/14316/14316_PT_Equation_3v2.svg" alt="Equation 3" /><img style="height:13px;" src="/files/ftp_upload/14316/14316_PT_Equation_4v2.svg" alt="Equation 4" />Um ein Kippen zu verhindern, m&#xFC;ssen die auf den Bus wirkenden Kr&#xE4;fte so ausbalanciert werden, dass das resultierende Moment um den unteren Punkt null sein muss. Dies hilft dabei, den maximalen Winkel f&#xFC;r ein Kippen zu bestimmen, um sicherzustellen, dass der Bus stabil bleibt, ohne umzukippen.

Reibung: Problemlösung

Friction is an essential force that influences the motion of objects in daily life. Depending on the situation, it can be either beneficial or ...

https://cloudfront.jove.com/files/ftp_upload/14316/14316_article_thumb_14316.jpg

Education

Lehre

JoVE Core

Mechanical Engineering

Maschinenbau

Unit 1

Einheit 1

Friction

Reibung

KEY TERMS AND CONCEPTS

KERNBEGRIFFE UND KONZEPTE

Friction: Problem Solving

friction on a banked road

Friction on a banked road affects whether a bus stays steady while it moves at constant speed. In this problem, a bus with a mass of three megagrams travels on a sloped road. The coefficient of static friction between the tires and the road is 0.5. The goal is to find the maximum bank angle where the bus will not slip or tip.

To solve the motion part, the forces on the bus must be shown first. These include gravity, the normal force, and friction. The normal force is the push from the road, and static friction is the grip that prevents sliding. The bus is then analyzed at the two tire contact points so the force balance can be checked.

Because the bus moves at a constant speed, it is in equilibrium. That means the vertical and horizontal forces cancel each other. Using the bus weight and the road angle, the maximum angle for no sliding can be determined from these balanced forces.

The tipping condition must also be checked. When tipping starts, the bus loses contact at the upper tire contact point. At that point, no reaction force or frictional force acts there. To avoid toppling, the moment about the lower contact point must be zero. That balance gives the largest safe bank angle without tipping.

Friction on a Banked Road

dry friction

Dry Friction in Crates and Everyday Motion

Dry friction appears when two solid surfaces touch and try to move past each other. Students can see it when they walk, slide a box across a table, or rub their hands together. Even though it is common, the forces behind it are not easy to see. A simple crate on a rough horizontal floor helps explain the idea. When an external force pushes the crate sideways, two main forces act on it. The normal force acts perpendicular to the surface and helps balance the crate’s weight, while the frictional...

static friction

Static Friction at the Point of Slip

Static friction is the force that keeps two surfaces from starting to slide past each other. It acts when there is a tendency for motion, but not yet actual slipping. This force helps explain everyday actions like walking on the ground and driving a car. A towing example shows how static friction changes as force is applied. A truck pulls a car with a rope, and the car stays still at first. The car is in static equilibrium, which means the forces on it are balanced. Gravity and the normal...

kinetic friction

Sliding Friction Between Moving Surfaces

Kinetic friction is the sliding friction that acts when two surfaces move against each other. It opposes relative motion and acts parallel to the contact surface, in the opposite direction of travel. In the truck and car example, the car first stays still because static friction holds it in place. When the truck’s force becomes greater than the limiting static frictional force, the friction at the contact surface drops to a lower value. The car then begins to slide, and its speed increases. At...

characteristics of dry friction

Static and Kinetic Dry Friction

Dry friction is the resistance between two solid surfaces that move against each other without lubrication or any fluid. A common example is a gardener pushing a wheelbarrow across the ground. The wheel and the ground create dry friction that slows the motion. Before the wheelbarrow starts to move, static friction acts at the contact surface. Static friction is the force that opposes motion before slipping begins, and it helps keep the wheelbarrow stable. It is present only when there is no...

types of friction problems

Dry Friction in Crate, Ladder, and Frame Problems

Dry friction problems often focus on crates, ladders, and frames that are close to slipping. Dry friction is the force that resists relative motion, or the tendency for motion, between two surfaces in contact. In many physics and engineering problems, this force helps keep an object still or defines the point where motion is about to begin. One common case has no clear impending motion. A force may be applied to a crate, but the crate stays at rest. The friction force between the floor and the...

friction: problem solving

Friction on a banked road affects whether a bus stays steady while it moves at constant speed. In this problem, a bus with a mass of three megagrams travels on a sloped road. The coefficient of static friction between the tires and the road is 0.5. The goal is to find the maximum bank angle where the bus will not slip or tip. To solve the motion part, the forces on the bus must be shown first. These include gravity, the normal force, and friction. The normal force is the push from the road,...

wedges

Wedges and Self-Locking Stability

A wedge is a simple machine that can lift, support, and split heavy objects. It can also change the height of structural or mechanical parts. Because it amplifies force, a wedge makes it easier to move or hold large loads with less effort. One example is lifting a heavy slab. In that case, the wedge turns the applied force into a much larger force that acts almost perpendicular to the original push. That force change helps raise the load without requiring a large input force. To analyze wedge...

frictional forces on screws

Square-Thread Screw Mechanics and Friction

Square-threaded screws use a helical thread to turn force into lifting motion. They are common fasteners, but they are also useful for transmitting power and motion in machines. A jack with a square-threaded screw lifts heavy loads when force is applied at the handle and the screw turns. A screw can be viewed as a cylindrical shaft with an inclined square ridge wrapped around it. The distance between two neighboring threads is called the pitch. The lead is the distance the screw advances in...

upward impending motion

Screw Jack Force and Friction Analysis

A square-threaded screw jack lifts heavy loads by turning handle force into a twisting moment. Its upward motion depends on overcoming static friction between the screw threads and the jack. To study this motion, the thread can be treated as if it were a block on the groove of the jack after the thread is completely unraveled. A free-body diagram helps show the forces acting on this simplified system. The force at the handle creates a horizontal force that pushes the movable thread up the...

self-locking screw

Screw Jack Self-Locking Behavior

A square-threaded screw jack can hold a heavy load because of its self-locking behavior. This feature makes the device more reliable when it is used to lift large weights or apply a strong force. If the screw keeps its position after the turning moment is removed, the jack is self-locking. Self-locking happens because friction changes the way the forces act on the thread. The friction force reverses direction, and the reaction force moves to the other side of the thread’s normal. In this case,...

screw: problem solving

Screw Torque and Self-Locking

Screw torque and self-locking are analyzed by looking at a threaded screw shaft and a plate gear. The shaft has a mean radius and a lead. The plate gear also has a mean radius. The coefficient of static friction between the screw and the gear is part of the setup. The first step is to find the static friction angle, φ. This angle is defined by the coefficient of static friction. Next, the lead angle is calculated from the lead and the mean radius of the shaft. It gives the screw geometry...

frictional forces on flat belts

Flat Belt Tension and Friction

Flat belt tension and friction control how power moves from one pulley to another. Flat belts are used in many industrial systems to transmit power between pulleys. As the belt wraps around the pulleys, the tension changes because of friction between the belt and the pulley surface. When a pulley turns counterclockwise, the belt side moving away from the pulley has the higher tension, called T2. The side moving toward the pulley has the lower tension, called T1. To estimate these tensions, the...

flat belts: problem solving

Flat Belt Forces and Pulley Moment

Flat belts transmit power from one pulley to another, and the forces on the belt help determine the moment on a pulley. In this example, a belt wraps around pulleys A and B, with radii of 30 cm and 10 cm. The belt meets the pulleys at a 20 degree angle from the horizontal, which sets up the force balance in the system. As pulley B rotates clockwise, it drives pulley A. That motion creates tension T2 on one side of the belt and tension T1 on the other side. The belt-to-surface contact angle, β,...

pivot bearings

Axial Load Support in Pivot Bearings

Pivot bearings support axial loads on a rotating shaft. A bearing helps two parts move relative to each other while reducing friction and wear. In this design, the pivot is placed at the end of the shaft to carry the axial thrust. The pivot surface can be flat, conical, or truncated, depending on the application. In a flat pivot bearing, the axial load is spread over the bearing area. The pressure is uniform and can be found by dividing the load by the area. To study the forces more closely,...

collar bearings

Friction Torque in Collar Bearings

Collar bearings support axial loads on rotating shafts, and their friction helps determine the torque needed to start motion. They are used in many machines and may have a single collar or multiple collars, depending on the application and load needs. For a single collar bearing under an axial load, the contact area is the ring-shaped region between the external radius and the internal radius of the collar. If the bearing is assumed to support the load evenly, the uniform normal pressure is...

journal bearings

Friction Moment in Journal Bearings

Journal bearings support rotating shafts and axles while helping keep them stable. They are used in machines such as engines, turbines, and pumps. Their job is to reduce friction, wear, and vibration. A journal bearing works by keeping a thin film of lubricant between the bearing surface and the rotating shaft. This film limits direct contact and lowers frictional force. The video uses a rope winch with dry or only partly lubricated journal bearings to show the idea. As the spool turns...

bearings: problem solving

Double-Collar Bearing Torque Calculations

Double-collar bearing torque calculations show how friction and axial force affect bearing performance. Engineers use these calculations to test whether the bearing can handle the forces and moments it experiences during operation. This helps them choose and design bearings for specific applications and setups. For a double-collar bearing with set dimensions and an axial force applied, the maximum frictional moment can be found with a standard expression. The equation is rearranged, and the...

rolling resistance

Tire Deformation and Rolling Resistance

Tire deformation and rolling resistance explain why a rolling wheel still needs a driving force. When a solid cylinder or tire rolls on a rigid surface, the normal force is perpendicular to the surface at the contact point. But real materials are not perfectly rigid, so the surface pushes back with a spread of normal pressures instead of one single force. A hard cylinder on a softer surface compresses the material under it. As the cylinder moves forward, the material in front of the contact...

rolling resistance: problem solving

Lawn Roller Force Calculation

Rolling resistance is the force that makes a rolling object harder to move across a surface. It is also called rolling friction. It comes from deformation in the object and the surface that touch each other. Internal friction, hysteresis, and other energy losses in the materials also play a role. Because of this force, extra energy is needed to keep a wheel, tire, or ball moving. The video applies this idea to a lawn roller. The roller has a mass of 100 kg, a radius of 25 cm, and a coefficient...

key terms and concepts

Find the maximum bank angle for a bus on a banked road by balancing gravity, normal force, static friction, and tipping moments.

Friction on a Banked Road | JoVE K12

JoVE Core Mechanical Engineering offers concise, easy-to-understand animated videos covering key topics such as equilibrium, forces, truss analysis, and structural mechanics. Explore their real-world applications, and witness these concepts in action through scientist-led experiments.

mechanical engineering

Friction on a Banked Road

Description

Transcript

Tags