Name: shear strain in a circular shaft
Uploaded: 2024-05-23T12:59:40.000Z
Duration: 1 min 10 s
Channel: JoVE

Eine einzigartige Eigenschaft von Kreiswellen ist, dass unter Torsion jeder Querschnitt flach und unverzerrt bleibt und sich wie eine feste starre Platte dreht.
Um die Verteilung der Schubspannung zu bestimmen, betrachten wir einen zylindrischen Querschnitt innerhalb einer kreisförmigen Welle der Länge L und des Radius R, der an einem Ende befestigt ist. Der Radius des zylindrischen Querschnitts ist r.
Betrachten Sie nun das kleine quadratische Element, das aus zwei benachbarten Kreisen und geraden Linien auf der Oberfläche des zylindrischen Abschnitts besteht, bevor eine Last aufgebracht wird.
Wenn die Torsionskraft auf die Welle aufgebracht wird, verformt sich das quadratische Element zu einer Raute. Da die beiden Seiten der Raute fest sind, ist die Schubdehnung gleich dem Winkel zwischen den Linien AB und A'B.
Mit Hilfe einer kleinen Winkelnäherung und einer geeigneten Geometrie kann gezeigt werden, dass die Schubdehnung an einem gegebenen Punkt einer Welle in Torsion proportional zum Verdrehwinkel und dem Abstand r von der Achse der Welle ist. Sie ist an der Oberfläche der Welle maximal.

verformung in einer kreisförmigen welle

Eines der charakteristischen Merkmale kreisförmiger Wellen ist ihre Fähigkeit, ihre Querschnittsintegrität unter Torsion beizubehalten. Mit anderen Worten: Jeder Querschnitt existiert weiterhin als flache, unveränderte Einheit und dreht sich einfach wie eine feste, starre Platte. Um die Verteilung der Scherspannung innerhalb einer solchen Welle zu verstehen, betrachten Sie einen zylindrischen Abschnitt innerhalb dieser kreisförmigen Welle. Dieser Abschnitt hat eine Länge von L und einen Radius von R, wobei ein Ende fest ist. Der Radius des zylindrischen Abschnitts wird mit r bezeichnet.

Bevor eine Last aufgebracht wird, betrachten Sie ein kleines quadratisches Element auf der Oberfläche des zylindrischen Abschnitts. Dieses Element wird durch zwei benachbarte Kreise und Geraden gebildet. Dieses quadratische Element verwandelt sich in eine Raute, wenn eine Torsionsbelastung auf die Welle ausgeübt wird. Vorausgesetzt, dass die beiden Seiten der Raute verankert sind, entspricht die Scherbelastung dem Winkel zwischen der vertikalen Linie AB, die an den Wänden des Zylinderabschnitts gezeichnet ist, und der geneigten Linie A'B, die entlang einer Seite der Raute gezogen ist. Durch Anwendung einer Kleinwinkelnäherung und geeigneter Geometrie lässt sich zeigen, dass die Scherbelastung an jedem bestimmten Punkt einer Welle, die einer Torsion ausgesetzt ist, direkt proportional zum Verdrehungswinkel und dem Abstand r von der Wellenachse ist. Diese Dehnung erreicht ihr Maximum an der Wellenoberfläche.

Verformung in einer kreisförmigen Welle

Eine einzigartige Eigenschaft von Kreiswellen ist, dass unter Torsion jeder Querschnitt flach und unverzerrt bleibt und sich wie eine feste starre Platte dreht.
An...

Education

Lehre

JoVE Core

Mechanical Engineering

Maschinenbau

Unit 1

Einheit 1

Torsion

KEY TERMS AND CONCEPTS

WICHTIGE BEGRIFFE UND KONZEPTE

Deformation in a Circular Shaft

shear strain in a circular shaft

Shear strain in a circular shaft describes how the shaft’s surface changes shape under torsion. A circular shaft keeps each cross-section flat and undistorted as it twists. Each section behaves like a rigid slab that rotates in place.

To study the strain inside the shaft, consider a cylindrical section with length L and radius R. One end of this section is fixed. The radius at a point inside the section is labeled r.

Before the load is applied, a small square element lies on the surface of the cylinder. It is formed by two neighboring circles and straight lines. When torsion is applied, that square element changes into a rhombus.

Because two sides of the rhombus stay anchored, the shearing strain can be measured by the angle between line AB on the cylinder wall and the inclined line A'B along one side of the rhombus. Using small-angle approximation and basic geometry, the shear strain at a point in the shaft is proportional to the angle of twist and to the distance r from the shaft’s axis. The strain is greatest at the outer surface.

Shear Strain in a Circular Shaft

stresses in a shaft

Torque and Shear in a Twisted Shaft

A shaft under torque develops internal shear forces as it twists. In this setup, equal and opposite torques act on the shaft PQ. To study the effect, a section is cut perpendicular to the shaft axis at an arbitrary point R. The free-body diagram of the QR segment shows the shearing forces applied by the PR portion. These forces act as the shaft resists twisting. Using equilibrium on the QR segment links the internal shear forces in the cut section to the internal torque. Here, r is the...

deformation in a circular shaft

Shear strain in a circular shaft describes how the shaft’s surface changes shape under torsion. A circular shaft keeps each cross-section flat and undistorted as it twists. Each section behaves like a rigid slab that rotates in place. To study the strain inside the shaft, consider a cylindrical section with length L and radius R. One end of this section is fixed. The radius at a point inside the section is labeled r. Before the load is applied, a small square element lies on the surface of...

circular shaft - stresses in linear range

Torsion Formula for Circular Shafts

Torsion in a circular shaft is analyzed when the applied torque stays within Hooke's law. In this linear range, the shaft does not undergo permanent deformation. The discussion uses shearing strain, shearing stress, and the modulus of rigidity to build the stress equation. The derivation also requires the moments of the small forces on a cross-section to equal the applied torque. When the shearing stress expression is rewritten, an integral term appears. This term represents the polar moment...

angle of twist - elastic range

Elastic Twist in a Circular Shaft

Elastic twist in a circular shaft describes how a cylindrical shaft rotates when torque is applied. The shaft has a length L and a uniform radius r. A torque at the free end creates shearing strain, which is greatest at points farther from the shaft axis. When the shaft stays within the elastic range, the shearing strain can be written in terms of the applied torque, radial distance, polar moment of inertia, and modulus of rigidity. The polar moment of inertia is a geometric measure of how the...

angle of twist: problem solving

Shaft Torsion Between Pulleys B and C

Shaft torsion between pulleys B and C is found by analyzing how torque twists an aluminum shaft. An electric motor applies 700 N·m of torque and produces stable rotation. The shaft carries pulleys B and C, which experience torques of 300 N·m and 400 N·m. The calculation starts with a section cut between pulleys B and C. A free-body diagram is used to study the cut cross-section. Because pulley B has an anticlockwise torque, the torque at the cut must balance it in the opposite direction. The...

design of transmission shafts

Sizing a Transmission Shaft by Torque

A transmission shaft is sized from the power it must carry and the speed it rotates at. These two design limits guide the choice of shaft material and cross-sectional size. The goal is to keep the maximum shearing stress within the elastic limit while still transmitting the needed power. Power is directly linked to torque, which is the twisting force applied to the shaft. By rearranging the power relation, the torque can be found from the required power and the shaft speed. That torque value...

stress concentrations in circular shafts

Why Shafts Develop Local Stress Peaks

Circular shafts can develop local stress peaks when torque is applied through real machine parts. The elastic torsion formula works best for a circular shaft with a uniform cross-section and rigid plates fixed to its ends. In practice, torque is often passed through flange couplings or gears, and these parts use keys in keyways to connect to the shaft. That loading method changes the stress pattern near the point where torque enters the shaft. The stress distribution no longer matches the...

plastic deformation in circular shafts

Torsional Failure and Plastic Strain in Shafts

Plastic deformation in circular shafts happens when torsional force pushes the material past its yield strength. At that point, the shaft does not return to its original shape. Instead, it keeps a permanent strain. To measure this change, the stress pattern inside the shaft must be understood. The maximum shearing stress is calculated first. Then a shearing-stress-strain diagram can be drawn to find the maximum shearing strain. Shearing strain changes linearly with the distance from the shaft...

circular shafts - elastoplastic materials

Torsion Limits in Circular Shafts

Circular shafts under torsion show a clear change from elastic behavior to plastic deformation as torque increases. In the elastic limit, stress rises in direct proportion to the distance from the shaft’s center. The outer material carries the highest stress first, and the shaft can still return to its original shape. At a critical stress level, the shaft begins to yield. This marks the maximum torque the shaft can carry without permanent deformation. Beyond this point, a plastic region forms...

residual stresses in circular shafts

Residual Stress After Shaft Torsion

Residual stress can remain in a circular shaft after torque causes plastic deformation. This happens in elastoplastic materials, which show both elastic and plastic behavior. The plastic change can come from high shearing stress or large strain. Residual stress is the internal stress that stays in the material after the external force is removed. In a shaft under torque, the angle of twist does not return fully to its original value. That lasting change shows that residual stress is still...

torsion of noncircular members

Torsion in Square and Rectangular Bars

Torsion in square and rectangular bars shows how shape changes the way a material twists. Circular shafts keep their cross-sections nearly unchanged because they are axis-symmetric. That symmetry helps the stress spread evenly, so the shaft can resist torsion without distorting. Square bars behave differently because they do not have the same axial symmetry. When twisted, their cross-sections distort, although the diagonals and the lines connecting the midpoints stay as exceptions. This means...

thin-walled hollow shafts

Shear Flow in Thin-Walled Shafts

Shear flow in a thin-walled hollow shaft describes how torsional force is carried through the wall. When a small segment of width dx is isolated, it is still in equilibrium, but it experiences torsional shearing forces at its ends. These forces come from the longitudinal shearing stress on the segment's minor surface multiplied by that surface area. The result is a uniform shear flow through the structure. To study the wall more closely, a small section with length ds is considered. The force...

key terms and concepts

Learn how torsion changes a circular shaft’s shape, why cross-sections stay flat, and why shear strain increases with distance from the axis.

Shear Strain in a Circular Shaft | JoVE K12

JoVE Core Mechanical Engineering offers concise, easy-to-understand animated videos covering key topics such as equilibrium, forces, truss analysis, and structural mechanics. Explore their real-world applications, and witness these concepts in action through scientist-led experiments.

mechanical engineering

Shear Strain in a Circular Shaft

Description

Transcript

Tags