Name: sliding friction between moving surfaces
Uploaded: 2023-09-22T11:49:28.000Z
Duration: 1 min 26 s
Channel: JoVE

Considere un camión tratando de mover un automóvil estacionado. A medida que el camión intenta tirar del automóvil, se crea una fricción estática en la superficie de contacto.
Cuando la fuerza aplicada excede la fuerza de fricción estática límite, la fuerza de fricción en la interfaz disminuye a un valor menor, llamado fuerza de fricción cinética. Luego, el automóvil comienza a deslizarse a una velocidad cada vez mayor.
La magnitud de la fuerza de fricción cinética es proporcional a la fuerza normal, siendo la constante de proporcionalidad el coeficiente de fricción cinética.
La ruptura continua de la interfaz es responsable de crear fricción cinética, que resiste el movimiento del automóvil.
A medida que aumenta la velocidad del automóvil, inicialmente, la fricción cinética disminuye lentamente. Sin embargo, a velocidades más altas, muestra una disminución significativa.
El ángulo entre la fuerza de fricción cinética y la fuerza normal resultante es el ángulo de fricción cinética. Siempre es menor o igual que el ángulo de fricción estático máximo.
El coeficiente de fricción cinética depende de la condición de la superficie y de la velocidad relativa entre las dos superficies.

<ol>
	<li>Hibbeler, R.C. (2016). Ingeniería Mecánica: Estática. Decimocuarta edición, Nueva Jersey: Pearson. Págs. 404.</li>
	<li>Meriam, J.L., Kraige, L.G. y Bolten, J.N. (2016). Ingeniería Mecánica: Estática y Dinámica. Octava edición, Singapur: John Wiley & Sons. Págs. 334-336.</li>
</ol>

fricción cinética

Considere un camión tratando de jalar un automóvil estacionario. A medida que el camión ejerce una fuerza sobre el automóvil, se crea fricción estática en el punto de contacto entre las dos superficies. Esta fuerza de fricción se opone al movimiento del automóvil y lo mantiene en reposo. Sin embargo, cuando la fuerza aplicada por el camión supera la fuerza de fricción estática límite, ocurre un fenómeno interesante. La fuerza de fricción en la interfaz se reduce a un valor más bajo, conocido como fuerza de fricción cinética. En este punto, el automóvil comienza a deslizarse y su velocidad aumenta. La fricción cinética, también conocida como fricción dinámica o fricción por deslizamiento, es la fuerza que se opone al movimiento relativo entre dos objetos en contacto mientras se están moviendo. Actúa paralela a la superficie de contacto y en dirección opuesta al movimiento. En el ejemplo del camión y el automóvil, la fricción cinética es la responsable de resistir el movimiento del automóvil a medida que comienza a deslizarse. La magnitud de la fuerza de fricción cinética es directamente proporcional a la fuerza normal que actúa sobre los objetos, con una constante de proporcionalidad que se denota como coeficiente de fricción cinética, el cual es una cantidad adimensional que depende de las propiedades y condiciones de las superficies en contacto. A medida que el automóvil comienza a deslizarse con mayor velocidad, la interfaz entre el camión y el automóvil experimenta un desgaste continuo. Este proceso es responsable de generar fricción cinética, la cual se opone al movimiento del automóvil. Interesantemente, la magnitud de la fricción cinética no se mantiene constante a medida que aumenta la velocidad del automóvil. Inicialmente, la fricción cinética disminuye lentamente, pero experimenta una disminución más significativa a velocidades más altas. El ángulo entre la fuerza de fricción cinética y la fuerza normal resultante se denomina ángulo de fricción cinética. Este ángulo siempre es menor o igual al ángulo máximo de fricción estática. Cabe destacar que el ángulo de fricción cinética depende de los materiales y las condiciones de las superficies en contacto. Varios factores, incluyendo la condición de las superficies en contacto y la velocidad relativa entre ellas, influyen en el coeficiente de fricción cinética. Las superficies más rugosas tienden a tener coeficientes de fricción cinética más altos, mientras que las superficies más lisas presentan valores más bajos. Además, los lubricantes o contaminantes pueden alterar el coeficiente de fricción cinética al cambiar las condiciones de la superficie.

Fricción cinética

Considere un camión que intenta tirar de un automóvil estacionado. A medida que el camión ejerce una fuerza sobre el automóvil, se crea una fricción estática en el punto de contacto ...

Education

Educación

JoVE Core

Mechanical Engineering

Ingeniería Mecánica

Unit 1

Unidad 1

Friction

Fricción

KEY TERMS AND CONCEPTS

TÉRMINOS Y CONCEPTOS CLAVE

Kinetic Friction

sliding friction between moving surfaces

Kinetic friction is the sliding friction that acts when two surfaces move against each other. It opposes relative motion and acts parallel to the contact surface, in the opposite direction of travel. In the truck and car example, the car first stays still because static friction holds it in place.

When the truck’s force becomes greater than the limiting static frictional force, the friction at the contact surface drops to a lower value. The car then begins to slide, and its speed increases. At that point, kinetic friction resists the motion of the sliding car.

The size of the kinetic frictional force depends on the normal force, which is the force pressing the surfaces together. It is proportional to that normal force through the coefficient of kinetic friction. This coefficient is a dimensionless value, and it depends on the materials and the condition of the surfaces in contact.

As the car keeps sliding, the interface between the truck and the car continues to break down. That breakdown helps produce kinetic friction. The force does not stay exactly constant as speed rises. It decreases slowly at first, then drops more at higher velocities.

The angle of kinetic friction is the angle between the kinetic friction force and the resultant normal force. It is always less than or equal to the maximum static friction angle. This angle also depends on the materials and surface conditions. Rougher surfaces usually have higher coefficients of kinetic friction, while smoother surfaces have lower values. Lubricants or contaminants can also change the coefficient by altering the surface conditions.

Sliding Friction Between Moving Surfaces

dry friction

Dry Friction in Crates and Everyday Motion

Dry friction appears when two solid surfaces touch and try to move past each other. Students can see it when they walk, slide a box across a table, or rub their hands together. Even though it is common, the forces behind it are not easy to see. A simple crate on a rough horizontal floor helps explain the idea. When an external force pushes the crate sideways, two main forces act on it. The normal force acts perpendicular to the surface and helps balance the crate’s weight, while the frictional...

static friction

Static Friction at the Point of Slip

Static friction is the force that keeps two surfaces from starting to slide past each other. It acts when there is a tendency for motion, but not yet actual slipping. This force helps explain everyday actions like walking on the ground and driving a car. A towing example shows how static friction changes as force is applied. A truck pulls a car with a rope, and the car stays still at first. The car is in static equilibrium, which means the forces on it are balanced. Gravity and the normal...

kinetic friction

Kinetic friction is the sliding friction that acts when two surfaces move against each other. It opposes relative motion and acts parallel to the contact surface, in the opposite direction of travel. In the truck and car example, the car first stays still because static friction holds it in place. When the truck’s force becomes greater than the limiting static frictional force, the friction at the contact surface drops to a lower value. The car then begins to slide, and its speed increases. At...

characteristics of dry friction

Static and Kinetic Dry Friction

Dry friction is the resistance between two solid surfaces that move against each other without lubrication or any fluid. A common example is a gardener pushing a wheelbarrow across the ground. The wheel and the ground create dry friction that slows the motion. Before the wheelbarrow starts to move, static friction acts at the contact surface. Static friction is the force that opposes motion before slipping begins, and it helps keep the wheelbarrow stable. It is present only when there is no...

types of friction problems

Dry Friction in Crate, Ladder, and Frame Problems

Dry friction problems often focus on crates, ladders, and frames that are close to slipping. Dry friction is the force that resists relative motion, or the tendency for motion, between two surfaces in contact. In many physics and engineering problems, this force helps keep an object still or defines the point where motion is about to begin. One common case has no clear impending motion. A force may be applied to a crate, but the crate stays at rest. The friction force between the floor and the...

friction: problem solving

Friction on a Banked Road

Friction on a banked road affects whether a bus stays steady while it moves at constant speed. In this problem, a bus with a mass of three megagrams travels on a sloped road. The coefficient of static friction between the tires and the road is 0.5. The goal is to find the maximum bank angle where the bus will not slip or tip. To solve the motion part, the forces on the bus must be shown first. These include gravity, the normal force, and friction. The normal force is the push from the road,...

wedges

Wedges and Self-Locking Stability

A wedge is a simple machine that can lift, support, and split heavy objects. It can also change the height of structural or mechanical parts. Because it amplifies force, a wedge makes it easier to move or hold large loads with less effort. One example is lifting a heavy slab. In that case, the wedge turns the applied force into a much larger force that acts almost perpendicular to the original push. That force change helps raise the load without requiring a large input force. To analyze wedge...

frictional forces on screws

Square-Thread Screw Mechanics and Friction

Square-threaded screws use a helical thread to turn force into lifting motion. They are common fasteners, but they are also useful for transmitting power and motion in machines. A jack with a square-threaded screw lifts heavy loads when force is applied at the handle and the screw turns. A screw can be viewed as a cylindrical shaft with an inclined square ridge wrapped around it. The distance between two neighboring threads is called the pitch. The lead is the distance the screw advances in...

upward impending motion

Screw Jack Force and Friction Analysis

A square-threaded screw jack lifts heavy loads by turning handle force into a twisting moment. Its upward motion depends on overcoming static friction between the screw threads and the jack. To study this motion, the thread can be treated as if it were a block on the groove of the jack after the thread is completely unraveled. A free-body diagram helps show the forces acting on this simplified system. The force at the handle creates a horizontal force that pushes the movable thread up the...

self-locking screw

Screw Jack Self-Locking Behavior

A square-threaded screw jack can hold a heavy load because of its self-locking behavior. This feature makes the device more reliable when it is used to lift large weights or apply a strong force. If the screw keeps its position after the turning moment is removed, the jack is self-locking. Self-locking happens because friction changes the way the forces act on the thread. The friction force reverses direction, and the reaction force moves to the other side of the thread’s normal. In this case,...

screw: problem solving

Screw Torque and Self-Locking

Screw torque and self-locking are analyzed by looking at a threaded screw shaft and a plate gear. The shaft has a mean radius and a lead. The plate gear also has a mean radius. The coefficient of static friction between the screw and the gear is part of the setup. The first step is to find the static friction angle, φ. This angle is defined by the coefficient of static friction. Next, the lead angle is calculated from the lead and the mean radius of the shaft. It gives the screw geometry...

frictional forces on flat belts

Flat Belt Tension and Friction

Flat belt tension and friction control how power moves from one pulley to another. Flat belts are used in many industrial systems to transmit power between pulleys. As the belt wraps around the pulleys, the tension changes because of friction between the belt and the pulley surface. When a pulley turns counterclockwise, the belt side moving away from the pulley has the higher tension, called T2. The side moving toward the pulley has the lower tension, called T1. To estimate these tensions, the...

flat belts: problem solving

Flat Belt Forces and Pulley Moment

Flat belts transmit power from one pulley to another, and the forces on the belt help determine the moment on a pulley. In this example, a belt wraps around pulleys A and B, with radii of 30 cm and 10 cm. The belt meets the pulleys at a 20 degree angle from the horizontal, which sets up the force balance in the system. As pulley B rotates clockwise, it drives pulley A. That motion creates tension T2 on one side of the belt and tension T1 on the other side. The belt-to-surface contact angle, β,...

pivot bearings

Axial Load Support in Pivot Bearings

Pivot bearings support axial loads on a rotating shaft. A bearing helps two parts move relative to each other while reducing friction and wear. In this design, the pivot is placed at the end of the shaft to carry the axial thrust. The pivot surface can be flat, conical, or truncated, depending on the application. In a flat pivot bearing, the axial load is spread over the bearing area. The pressure is uniform and can be found by dividing the load by the area. To study the forces more closely,...

collar bearings

Friction Torque in Collar Bearings

Collar bearings support axial loads on rotating shafts, and their friction helps determine the torque needed to start motion. They are used in many machines and may have a single collar or multiple collars, depending on the application and load needs. For a single collar bearing under an axial load, the contact area is the ring-shaped region between the external radius and the internal radius of the collar. If the bearing is assumed to support the load evenly, the uniform normal pressure is...

journal bearings

Friction Moment in Journal Bearings

Journal bearings support rotating shafts and axles while helping keep them stable. They are used in machines such as engines, turbines, and pumps. Their job is to reduce friction, wear, and vibration. A journal bearing works by keeping a thin film of lubricant between the bearing surface and the rotating shaft. This film limits direct contact and lowers frictional force. The video uses a rope winch with dry or only partly lubricated journal bearings to show the idea. As the spool turns...

bearings: problem solving

Double-Collar Bearing Torque Calculations

Double-collar bearing torque calculations show how friction and axial force affect bearing performance. Engineers use these calculations to test whether the bearing can handle the forces and moments it experiences during operation. This helps them choose and design bearings for specific applications and setups. For a double-collar bearing with set dimensions and an axial force applied, the maximum frictional moment can be found with a standard expression. The equation is rearranged, and the...

rolling resistance

Tire Deformation and Rolling Resistance

Tire deformation and rolling resistance explain why a rolling wheel still needs a driving force. When a solid cylinder or tire rolls on a rigid surface, the normal force is perpendicular to the surface at the contact point. But real materials are not perfectly rigid, so the surface pushes back with a spread of normal pressures instead of one single force. A hard cylinder on a softer surface compresses the material under it. As the cylinder moves forward, the material in front of the contact...

rolling resistance: problem solving

Lawn Roller Force Calculation

Rolling resistance is the force that makes a rolling object harder to move across a surface. It is also called rolling friction. It comes from deformation in the object and the surface that touch each other. Internal friction, hysteresis, and other energy losses in the materials also play a role. Because of this force, extra energy is needed to keep a wheel, tire, or ball moving. The video applies this idea to a lawn roller. The roller has a mass of 100 kg, a radius of 25 cm, and a coefficient...

key terms and concepts

Learn how kinetic friction acts during sliding motion, why it changes as surfaces move, and how surface type, normal force, and lubrication affect it.

Sliding Friction Between Moving Surfaces | JoVE K12

JoVE Core Mechanical Engineering offers concise, easy-to-understand animated videos covering key topics such as equilibrium, forces, truss analysis, and structural mechanics. Explore their real-world applications, and witness these concepts in action through scientist-led experiments.

mechanical engineering

Sliding Friction Between Moving Surfaces

Description

Transcript

Tags