11.9
Rectificador de onda completa
Un rectificador de onda completa es un dispositivo que convierte corriente alterna (CA) en corriente continua (CC) y es más eficiente que su contrapar…
Considere un circuito rectificador de onda completa que comprende un transformador con derivación central, dos diodos en una configuración con derivación central y una resistencia de carga.
El devanado secundario del transformador suministra dos voltajes de entrada iguales con polaridades opuestas a través de las dos mitades del devanado secundario.
Durante los semiciclos positivos de la señal de entrada, cuando el voltaje excede o es igual a la caída de voltaje directo del diodo, el diodo D1 conduce mientras que D2 tiene polarización inversa. La forma de onda de salida se asemeja a la de un rectificador de media onda.
Por el contrario, durante el semiciclo negativo, cuando el voltaje de entrada es menor que la caída de voltaje directo del diodo, el diodo D1 se corta mientras D2 conduce. Una vez más, la forma de onda de salida refleja la de un rectificador de media onda.
La corriente a través de la resistencia fluye constantemente en la misma dirección, lo que da como resultado una salida unipolar.
La mayor eficiencia de rectificación de un rectificador de onda completa permite su uso en fuentes de alimentación, cargadores de baterías, amplificadores de audio y procesamiento de señales.
El voltaje inverso máximo es el doble del voltaje de entrada máximo menos la caída de voltaje directo del diodo, que es aproximadamente el doble que el caso del rectificador de media onda.
View the full transcript and gain access to JoVE Core videos
Q1: How does a full-wave rectifier convert AC to DC?
A full-wave rectifier converts alternating current to direct current by using a center-tapped transformer and two diodes that conduct on alternate half-cycles. During the positive half-cycle, diode D1 becomes forward-biased and conducts while D2 is reverse-biased. During the negative half-cycle, D1 is reverse-biased and D2 conducts, flipping the negative voltage to positive. This ensures unidirectional current through the load resistor, producing a unipolar DC output.
Q2: What is the role of the center-tapped transformer in a full-wave rectifier?
The center-tapped transformer is the pivotal element of full-wave rectification. Its secondary winding is divided to provide two equal voltages of opposite polarities across the two halves. This dual-voltage configuration allows each diode to conduct during alternate half-cycles of the AC input, enabling the circuit to utilize the full cycle of the AC waveform rather than just half of it.
Q3: Why is a full-wave rectifier more efficient than a half-wave rectifier?
A full-wave rectifier has higher rectification efficiency because it utilizes both the positive and negative half-cycles of the AC input signal, whereas a half-wave rectifier uses only one half-cycle. Additionally, the full-wave rectifier produces lower ripple voltage at double the ripple frequency, yielding smoother DC output with less filtering requirement compared to a half-wave rectifier.
Q4: What is peak inverse voltage in a full-wave rectifier?
Peak inverse voltage (PIV) is the maximum reverse voltage a diode must withstand in the circuit. In a full-wave rectifier, the PIV equals twice the maximum input AC voltage minus the diodes' forward voltage drop. This PIV is approximately double that encountered in a half-wave rectifier, requiring diodes that can sustain higher reverse voltages to ensure safe operation.
Q5: What are the main applications of full-wave rectifiers?
Full-wave rectifiers are extensively used in power supply units, battery chargers, audio amplifiers, and signal-processing applications. Their increased rectification efficiency and smoother DC output make them ideal for these applications where stable, continuous direct current is required. The reduced ripple voltage and higher ripple frequency minimize the need for additional filtering components.
Q6: How does the output waveform differ between the two diodes in a full-wave rectifier?
Each diode in a full-wave rectifier produces an output waveform resembling that of a half-wave rectifier during its respective conduction period. When D1 conducts during positive half-cycles, it generates a positive output. When D2 conducts during negative half-cycles, it flips the negative voltage to positive. Combined, these alternating outputs create a continuous unipolar waveform with current flowing consistently in the same direction through the load resistor.
Q7: What determines when each diode conducts in a full-wave rectifier?
Diode conduction is determined by the input signal polarity and the diode's forward voltage drop threshold. During positive half-cycles, when voltage exceeds the diode's forward voltage drop, D1 conducts while D2 is reverse-biased. During negative half-cycles, when input voltage is lower than the forward voltage drop, D1 is cut off while D2 conducts. This alternating conduction pattern ensures full-wave rectification of the AC signal.