Name: preparing samples by state and form
Uploaded: 2024-12-05T18:31:54.000Z
Duration: 1 min 21 s
Channel: JoVE

サンプル調製は、正確な分析結果を得るための重要なステップです。これは、抽出、精製、濃縮の3つの主要な目的で構成されています。
まず、抽出では、サンプルマトリックスから目的の分析種を含む混合物を分離します。次に、干渉物質が存在する場合は、それらを除去して純粋なサンプルを取得します。第三に、抽出された分析物が低濃度の場合、正確に検出できるレベルまで濃縮されます。
サンプルの一般的な形態は、固体、液体、および気体です。直接分析するには大きすぎる固体の塊は、粉砕、破砕、粉砕などの物理的方法で粉末化されます。
この混合物をふるい分けてブレンドすると、均質な微粉末が得られ、これを乾燥させて適切な溶媒に溶解し、分析対象物を溶液に抽出します。 
固体とは異なり、液体懸濁液は分析前にろ過または遠心分離され、不純な固体粒子が除去されます。
固体吸着剤がガス状分析種を選択的に吸着するため、ガスのサンプル調製は必要ありません。

分析のためのサンプル準備: 概要

サンプル準備は、分析プロセスに不可欠なステップです。サンプルを正確に分析できるように準備する作業です。目標は、分析を妨げる可能性のある成分を除去しながら、測定したい物質である分析物をサンプルから抽出することです。サンプル準備の手法は、サンプルの物理的状態によって異なります。

バルクまたは大きな固体サンプルは通常、粉砕、破砕、または製粉技術を使用してサイズを小さくし、サンプルの表面積を増やして、より効率的な分析を提供します。粉砕後、サンプルはふるいにかけられ、均一な組成になるように混合されます。次に、粉末サンプルを適切な溶媒に溶解して、固体マトリックスから分析物を抽出します。溶媒の選択は、分析物の性質とサンプル成分の溶解特性によって異なります。

浮遊固体粒子または沈殿物を含む液体サンプルは、通常、ろ過または遠心分離にかけられ、液体から固体不純物が分離されます。濾過では液体をフィルターに通しますが、遠心分離では遠心力（回転力）を利用して固体を液相から分離します。分析物が微量に存在する場合、液体サンプルは濃縮工程の前処理を受け、分析物の濃度を高めて検出を向上させます。

ガスサンプルは分析機器に直接導入できるため、ガス状分析物の分析ではサンプル準備は通常不要です。

サンプル調製は、分析プロセスにおいて重要なステップです。これには、正確に分析できるようにサンプルを準備することが含まれます。目標は...

Education

JoVE Core

Analytical Chemistry

分析化学

Unit 1

ユニット1

Method Development and Sampling Techniques

分析法の開発およびサンプリング技術

method-development-and-sampling-techniques

KEY TERMS AND CONCEPTS

主要用語と概念

Sample Preparation for Analysis: Overview

preparing samples by state and form

Sample preparation depends on the state and form of the sample before analysis. It helps make the sample ready for accurate measurement. The main goal is to extract the analyte, which is the substance being measured, and remove parts that could interfere with the analysis.

Solid samples often need the most handling. Large solids are usually ground, crushed, or milled to make them smaller and increase surface area. The sample is then sieved and mixed so it has a uniform composition. After that, the powdered material is dissolved in a suitable solvent to pull the analyte out of the solid matrix. The best solvent depends on the analyte and on how well the sample components dissolve.

Liquid samples may also need treatment before analysis. If they contain suspended solids or precipitates, they are usually filtered or centrifuged to remove the unwanted particles. Filtration works by passing the liquid through a filter. Centrifugation uses spinning force to separate the solid material from the liquid phase.

When the analyte is present in trace amounts, liquid samples may need a concentration step. This increases the analyte level so it is easier to detect. Sample preparation is usually not needed for gaseous analytes because the gas sample can be introduced directly into the analytical instrument.

Preparing Samples by State and Form

development of analytical methods

Analytical Methods: Technique to Protocol

Analytical methods follow a clear path from technique to protocol. In analytical chemistry, a technique is the scientific principle used to explain a chemical measurement. A method applies that technique to a sample of interest. The next steps are procedure and protocol. A procedure gives the directions for carrying out the analysis with an analytical method. A protocol is the detailed set of guidelines for that procedure, and it should be followed closely to get the desired results. <br...

quality control

Quality Control Charts and Lab Records

Quality control charts, proficiency testing, and lab records are key parts of quality control in a laboratory. These steps help keep a system under statistical control. They also help track data, show trends, and spot variations that may affect the accuracy of an analysis. One common tool is a quality control chart. This chart plots one or more analytical characteristics over time. The measured values are taken at different times during the analysis and compared with the known value of...

quality assurance

Quality Checks in Analytical Testing

Quality assurance in analytical testing brings together the checks that help a system perform properly. It includes quality control, quality assessment, and internal corrective measures. These parts work in a cycle to support reliable results. Quality control happens before and during the analysis. Quality assessment takes place during and after the investigation. Internal corrective measures are then based on the results of post-analysis quality assessment, or they may be applied before a new...

data validation

How Analytical Methods Are Checked

Method validation checks whether an analytical chemistry method gives reliable results. It is especially important when the same method is used with different sample matrices or when the procedure is changed. Validation helps show that the method still meets acceptable standards in each case. Several key checks are used in method validation. Specificity means the method can measure the target analyte without interference from other substances. Linearity means the result changes in direct...

qualitative analysis

Classical and Instrumental Sample ID

Qualitative analysis identifies the elements, ions, or compounds in an unknown sample. It is the first step in the hierarchy of analytical goals. That makes it the starting point for scientific study before quantitative analysis or other forms of analysis. Two main approaches are used in qualitative analysis: classical methods and instrumental methods. Classical methods depend on the visible or sensory result of a chemical reaction, such as a color change, a precipitate, or even a smell. These...

quantitative analysis

Measuring Analyte Concentration

Quantitative analysis measures the amount of a specific substance, called the analyte, in a sample. If the sample composition is unknown, qualitative analysis comes first. That step identifies the components so the correct substances can be measured during the quantitative phase. This method depends on two key measurements. Scientists measure the sample quantity and also a property that is proportional to the amount of analyte. Together, these measurements help determine the analyte...

instrument calibration

Calibrating Lab Instruments for Accurate Results

Calibration helps lab instruments produce accurate and consistent results. It is important in manufacturing, healthcare, testing laboratories, and scientific research. Each instrument needs a calibration process that matches its design and function. This process improves data accuracy and helps results stay reliable. An analytical balance measures mass and needs regular calibration to stay precise. It is calibrated by comparing its readings with known standard weights. These weights act as...

glassware calibration

Calibrating Lab Glassware for Accurate Volume

Calibrating lab glassware helps students measure liquids accurately in the analytical laboratory. It reduces volume errors and supports consistent results across measurements. This matters when using volumetric flasks, pipettes, burettes, and other tools that depend on precise volume readings. Volumetric flasks are used to prepare aqueous solutions with a precise final volume. They have a calibration line on the neck. To calibrate one, fill it with distilled water until the meniscus, the...

standard solutions

Preparing Standard Solutions in the Lab

Standard solutions are prepared to have a precisely known concentration or composition. In analytical chemistry, this accuracy is important because it supports reliable results. A primary standard is a highly pure, stable substance with a high molar mass. It is fully soluble in water, which is the most commonly used solvent in analytical chemistry. A primary standard solution can be used to standardize a secondary standard. Secondary standards have known concentrations, but they are usually...

blank solutions

Blank Solutions in Analytical Testing

Blank solutions are used in analytical testing to show the background signal before a sample is measured. A blank solution does not contain the analyte, which is the substance of interest being tested or measured. It is usually made with the same reagents and procedure as the sample solution, but without the analyte. The main purpose of a blank solution is to control for background interference and contamination. Reagents, solvents, or lab equipment can sometimes create a detectable signal on...

sampling methods: overview

How Sampling Shapes Lab Results

Sampling shapes lab results by determining how a smaller sample represents a larger population. In analytical chemistry, testing an entire population is often impractical or impossible, so samples are collected to make inferences about the whole group. The sampling method is the process used to choose individuals or items for that sample. Common sampling methods include random, judgemental, systematic, stratified, and cluster sampling. Each method can affect the quality of the data in a...

sampling methods: sample types

Sampling Materials in Solid, Liquid, Gas

Sampling materials are grouped as solid, liquid, or gas. The type of sample helps decide the right collection method. Solid samples can include sediments from water bodies, soil, metals, and biological tissues. Sediment sampling from water bodies can be done in two common ways. Grab sampling uses a device to collect a discrete sample from the bottom with minimal disturbance. These samples may not show the full area because conditions can vary from place to place. Piston coring collects a...

sampling plans

Choosing Samples for Reliable Results

Sampling is a key step in analytical chemistry. It helps researchers collect data that represents a larger population. The main sampling methods in this topic are random, judgmental, systematic, stratified, and cluster sampling. Random sampling gives each member of the population an equal chance of being chosen. Researchers often use a random number generator or a lottery-style method. For example, a polymer sheet can be divided into 1 cm x 1 cm sections, and 10 sections can be selected at...

sample preparation for analysis: overview

Sample preparation depends on the state and form of the sample before analysis. It helps make the sample ready for accurate measurement. The main goal is to extract the analyte, which is the substance being measured, and remove parts that could interfere with the analysis. Solid samples often need the most handling. Large solids are usually ground, crushed, or milled to make them smaller and increase surface area. The sample is then sieved and mixed so it has a uniform composition. After that,...

sample preparation for analysis: advanced techniques

sample-preparation-for-analysis-advanced-techniques

Preparing Complex Samples for Analysis

Preparing complex samples for analysis often requires special digestion and fusion methods. Samples with inorganic or organic material can be hard to dissolve or break down. Common sample preparation methods include acid digestion, fusion, dry ashing, and wet digestion. These steps help turn difficult samples into forms that can be tested reliably and again with similar results. Acid digestion is often used for inorganic materials that do not dissolve in water. It is useful for soil and...

sample handling

Sample Transport and Storage Basics

Sample transport and storage help keep specimens intact before testing. Moving a sample from the collection point to the laboratory requires careful handling. The sample should be sealed well and clearly labeled. These steps help prevent cross-contamination and support reliable results. Temperature control is also important during transport. Some samples travel in insulated containers, cool packs, or refrigerated vehicles so they stay within the needed temperature range. After the samples...

contaminants and errors

Sampling Errors in Sample Preparation

Sampling errors in sample preparation can affect the accuracy of laboratory results. Two common problems are concentration bias from poor sample splitting and contamination from reducing particle size by grinding or homogenization. Recognizing these errors helps make analysis more reliable. The number of samples also matters when a target population follows a normal distribution. In that case, the sample size ns can be found with a formula that uses the t-value for the chosen confidence level,...

key terms and concepts

Learn how sample preparation changes for solids, liquids, and gases, including grinding, filtering, centrifuging, and concentration steps for accurate analysis.

Preparing Samples by State and Form | JoVE K12

JoVE Core 分析化学 は、複雑な化学原理をアニメーションで視覚化することで、SI 単位から NMR 分光法を含むトピックをよりわかりやすくします。実験を撮影した実写動画では、これらの概念が世界中の研究所でどのように応用されているかを取り上げています。

analytical chemistry

Preparing Samples by State and Form

Description

Transcript

Tags